Edge-core ECS4150-28T L2+-L3 Lite Gigabit Ethernet (PoE) Switch User Manual
- June 16, 2024
- Edge-core
Table of Contents
Edge-core ECS4150-28T L2+-L3 Lite Gigabit
**Ethernet (PoE) Switch User Manual**
Package Contents
- L2+/L3 Lite Gigabit Ethernet (PoE) Switch
- Rack mounting kit—2 brackets and 6 or 8 screws
- Power cord
- Console cable—RJ-45 to DE-9
- Four adhesive rubber feet (28-port switches only)
- Grounding wire
- Four or six port dust covers
- Documentation—Quick Start Guide (this document) and Safety and Regulatory Information
Overview
- System LEDs
- 24 x 10/100/1000M RJ-45 ports
- 4 x 1/10G SFP+ ports
- Management port, Console port, and USB port
- 24 x 10/100/1000M RJ-45 PoE ports
- 48 x 10/100/1000M RJ-45 ports
- 6 x 1/10/25G SFP28 ports
- 40 x 10/100/1000M RJ-45 PoE+ (IEEE 802.3at) ports
- 8 x 10/100/1000M RJ-45 PoE++ (IEEE 802.3bt) ports
- PoE LED and Mode button
- Ground screw
- AC power socket
System/Port LEDs & Buttons
- PWR : Green (OK)
- SYS : Green (OK), Blinking Green (booting)
- PoE : Green (OK)
- Mode Button: Port LED PoE status on/off
- RJ-45 1G Ports: Green/Blinking (link/activity)
- SFP+/SFP28 Ports : Green/Blinking (link/activity)
Warning : For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty.
Note : The drawings in this document are for illustration only and may not match your particular model.
1) Mount the Device
1. Attach the Brackets
Use the included flathead M4x8 screws to attach the brackets.
2. Mount the Device
Mount the device in the rack and secure it with rack screws.
2) Ground the Device
Connect the included grounding wire to the grounding point on the rear panel. Then connect the other end of the wire to rack ground.
3) Connect Power
Connect
an AC power source to the device.
4) Make Network Connections
RJ-45 PoE Ports
Connect Cat. 5e or better twisted-pair cable.
SFP+/SFP28 Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports. The following transceivers are supported:
- 1000BASE-SX/LX/EX/ZX and 1000BASE-T (RJ-45)
- 10GBASE-SR/LR
- 25GBASE-SR/LR
Alternatively, connect DAC or AOC cables directly to the port slots.
5) Make Management Connections
RJ-45 Console Port
Connect the included console cable and then configure the serial connection:
115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow
control.
USB Port
The USB 2.0 port allows you to copy a runtime or configuration file to/ from a
USB memory stick. (The USB port only supports a simple data storage device
using a FAT16/32 file system with or without a partition table.)
Warranty Information and Technical Support
Registering your product enables you to receive a more efficient warranty
service. Be sure to register at www.edge-core.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>