Duclsaty Caged Ceiling Fan with Light and Remote Control Installation Guide

: June 16, 2024
: Duclsaty

Table of Contents

Installation Guide
Installation preparation
Installation Steps
Lamp shade Installation
Bulb Base Assembly
Down rod installation
Hang the fan to the Ceiling
Connecting wires
Canopy Mount
Remote Control Introduction
Quick answers to common Questions
Trouble Shooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Duclsaty Caged Ceiling Fan with Light and Remote Control Installation Guide

Installation Guide

To reduce the risk of electric shock, turn off the electricity to the fan at the main fuse box or circuit panel before installation.
All wiring must be in accordance with the local electrical codes or National Electrical Code. Electrical installation should be performed by a qualified licensed electrician.
To avoid personal injury, a pair of gloves is necessary while handling fan parts with sharp edges.
Make sure the installation site you choose allows clear space for the blades to rotate and at least seven 7 feet (2.13 meters) of clearance between the floor and the fan blade tips. The fan should be mounted so that the tips of the blades are at least thirty 18 inches (45.72 centimeters) from walls or other upright structures.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
The outlet box and ceiling support structure must be securely mounted and capable of supporting at least 45KGs.
To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
Electrical diagrams are for reference only.
The fan is suitable for indoor and covered outdoor use only.

Installation preparation

**TOOLS REQUIRED

**

Cut off power supply before installation
Suggest to have someone to help you
All the screws and down rods should be nice and solid when you finish the step
Unpack your fan and check the contents. You should have followings,
Mounting Bracket X 1
Canopy Screws X 2
Canopy X 1
Donwood & Hanger Ball X 1
Lock Pin X1
Hitch Pin X1
Coupling Cover X 1
Fan Motor X 1
Fan Blades
4 x Standard E26 Bulb Base & Driver x 1
Lamp Shade X 1
Remote Receiver X 1
Remote Controller X 1
Wood Screws X 4
Expansion Screws X 2

Installation Steps

Lamp shade Installation
Bulb Base Assembly
Down rod installation
Hang the fan to the Ceiling
Connecting wires
Canopy Mount
Remote Control Introduction
Quick answers to common Questions
Trouble Shooting

Lamp shade Installation

Put a towel on the canopy to avoid paint scratch. **(From Pic.1 to Pic.2)

**

Put the fan motor as below and make a steady surface as **Pic.3.

**

Put the Lamp shade on the fan motor surface. Make sure the 4 holes in the motor align4holesinthe Lamp shade as **Pic.4.

**

. Screw down 4 BLACK screws which is unique because all the other screws are not black color. see Pic.5.

Please do not tighten the 1st screw too tight just finish the tightening of the 2nd and the 3rd screw then go back to the 1st screw to finish the tightening, finally the 4th screw otherwise it would be difficult. Screws would be numbered as **Pic.6.

**

Bulb Base Assembly

Find the silver colored extension rod in the screw pack **Pic.6A

,remove one screw and the black cap Pic.6B** ,

put them aside as they will be used in next steps. Then screw the extension rod to the hole shown in Pic.7.

Tighten the silver washer as Pic.8.Screw until is it tight.

Get the black plate with two holes as Pic.9. Pull out the wires to make it longer for easy operation **(Pic.9A)

Pass the down rod and the wires through the holes as Pic. 10. Operation as Pic.10A
& Pic.10B.Screw down the other screw as Pic. 10C**.Pay attention the black plate orientation.

Find the bulb base and pull out the wires in it **Pic.11

Then assemble the bulb base to the fan Motor base, connect the wires white to white, blue to blue. Just Insert into each other as Pic.12. Pic.12A** for reference.
Keep the black plate and the bulb base as below circles and find the black round cap and spinet to the position as the green arrow directs in **Pic.13.

**

If you found the round cap cannot be perfectly tightened as Pic.14 , it is because the tail of the Extension rod is too long or too short, thus you have to go back to Pic.8 to adjust the length of the extension rod by rotating the screw up or down.

Down rod installation

Put the ceiling fan upside as Pic.15.

Get the down rod and remove the R-shaped lock pin and hitch pin from Pic.16 to Pic. 17.

There are two different down rod size,4in for lower ceiling and 8inch for higher ceiling. Choose one as you want.
Assemble the canopy **Pic.18

and coupling cover Pic.19

below to the down rod as Pic.20.

Pay attention** the canopy and the cover should be back to back.

Unpack and Collect the wires as Pic.21 all and get passed through the down rod as Pic. 22.
Insert the down rod to the fan motor base. Look at Pic.23 the two holes are not in the same position but the correct action is two holes should be on the same position after completely insert the down rod.
Insert the lock pin. To make this step easier, please take your screw driver and push the screw driver through between the wires in the down rod ( Pic.24 ) and get that lock pin slides through, you just push it on the end **(Pic.25)

and it just glide through (Pic.26 &Pic.27**), otherwise it can be that difficult because there are wires in the down rod which may block the bolt when slide through.

Put the R shaped hitch pin into the lock pin in Pic. 28 and tighten the TWO screws in **Pic.29.

Then pull down the coupling cover Pic.29B.

**

Hang the fan to the Ceiling

CUT OFF the power supply for SAFTY!!!
Fix the mounting bracket

Fig.1 for Concrete Ceiling. Mark the location for the ceiling fan first, then drill two holes in the ceiling to aid in securing mounting bracket with TWO expansion screws provided in Pic.30, and secure the mounting bracket to the building. Please keep the two screws in circles in Pic.31 HALF LOOSE as it is. DO NOT TIGHTEN THEM.

Fig.2 for Wood Ceiling. Mark the location for the ceiling fan first, use the FOUR wood screws in Pic.30, then tighten the four screws to the wood ceiling Pic.31. Please keep the two screws in circles HALF LOOSE as it is. DO NOT TIGHTEN THEM.

Hold the Ceiling fan at the point as Pic.32 and carefully lift to the ceiling and sit the hanger ball to the mounting bracket as Pic.33.

Rotate the down rod until the notch on the hanger ball engaged the ridge on mounting bracket in Pic.34 &Pic.34a

Down rod can not be rotated if the step is done properly otherwise the fan will wobbles when it is working.

Connecting wires

It is a bit tricky yet it would not be issue if you assembled based on the illustration below.
Insert the black remote receiver to the interspace up on the mounting bracket as **Pic.35.

Pic.36 shows how the wires going, connecting white to white, blue to blue, red to red. Just buckle each other in the same color. Leave the antenna as it is, no need to connect with any wire. Connect the black live wire and the white neutral wire to the power cord from the ceiling electric box by giving a couple of twists and tighten the cap in Pie. 40**.

Make sure the interface of the red wire in Pic. 36 do not diverge otherwise there will be insufficient power of the fan when working.

Canopy Mount

Reorganize the wire Pic.37 and lift the canopy as **Pic.38.

Attention there is limit room of the canopy so you have to keep all the wires in order to squeeze the wires into the canopy. Spin the canopy until the two half loose canopy screws are locked in the smaller hole then tighten down the TWO screws as Pic.39.
**

All done! Installation Finished.
Mount 4 Edison Bulbs, Ducsay Ceiling Fans with lights can be used as fan and/or lights as you like.

Remote Control Introduction

Remote Control
Customer Service we provide

Damaged Parts Replacement
Missing Parts Replenishment
Professional Installation Guide
Other Customized Products and Service

Feel free to contact Amazon

Quick answers to common Questions

Can the light and fan work separately? Like, can I turn on just the fan without turning on the light and vice versa?
Yes, the light and the fan can work separately, controlled by remote control
Do you have instructions on how to installation?
Yes we have detailed video on how to installation for the the same product. Video can be found when you scan the QR code on the first page of the manual or our product link at Amazon.
How do you change the blade speed, I cannot get it to change?
Use the remote control. Level 1-6 speed adjustment by press 1-6 button.
Can this fan be installed on a concrete ceiling?
Yes, it can. See detailed installation guide on Page.13.
Can I buy a replacement remotes?
We will surely support you when you have issue during you install or use the product like parts replacement or installation guide Please contact Amazon whenever you have questions and Amazon will forward your require to us. We will feedback with optimized solution within 24hours.
Does the remote control require a battery, if so what size?
Yes, it needs two AAA battery. The remote control does not contain batteries.
Is this a DC motor? Is DC different from AC?
Yes, the ceiling fan is DC motor driven DC motor is much more efficient and durable than AC ones. Fan blades can reverse by DC motor by pressing one button on the remote controller.
My ceiling has a 15 degree slope. Can this down rod be angled at 15 degrees, or do I need a separate one?
This down rod can be angled at 15 degree yet we suggest you transform your ceiling to flat by some fixture just for fan stabilization and safety purpose.
Does the ceiling fan have bulbs included?
No, the ceiling fan does not have bulbs included due to the bulbs are fragile. You can purchase some Edison bulbs from you local store.
Can this be installed where an existing light was without extra wiring involved for the fan portion of this fixture?
Yes, it can be installed where an existing light was without extra wiring involved. Just remove your existing light and install the new ceiling fans.
If I get two ceiling fan ,can I sync them with one remote?
Yes, you can sine two ceiling fan with one remote. Standard package is one remote control for one unique ceiling fan. To achieve one remote sine two ceiling fans with lights, you have to re-code the remote as below. Steps are,
Put two AAA batteries into the Handheld remote control that you want to use to sync two ceiling an.
Connect the Black remote receiver’s black Live line and white Neutral Line with your power cord from the ceiling.
Turn on the power supply and wall switch. After you hear a tick, immediately press controller buttons in proper order as FAN/OFF—>LIGHT ON/OFF—>FAN/OFF.
Press Speed button 1-6 and timer 1H,2H,4H and the coding is successfully if you hear tickeachtime you press.
Will this work with a longer down rod?
Yes, it does work with down rod length of different size from 4inch to 23.6inch.Current standard
package includes two down rods of 4inch and 8inch which can meet most of demands. We also could
offer longer down rod if you need. Feel free to contact Amazon message or directly raise your require
on Amazon QA function. We can support you all the way until you are most satisfied.
Can I replace the bulbs by myself?
Yes, you can. Please make sure to cut off the power supply before you start the replacement.
Can this used in exterior space?
If the exterior space is some covered space, then yes. But we suggest to use indoors only as the product is not waterproof.
How can I get to you if I find parts is broken when I unbox it?
When parts is damaged accidentally during transportation thus you cannot install the ceiling fan
perfectly. You can turn to Amazon customer service, Amazon will forward your request to us. We will immediately look into the case and provide the most suitable solution to you like new parts replacement.
If you have any other questions regarding ceiling fan installation or operation, feel free to contact Amazon customer service or raise a question on Amazon Q/A section.
We live for bringing a smile to each and every customer’s face and we are gonna do our hardest to make that happen right now. We are tent on making everything right as long as you will give us a chance.

Trouble Shooting

The light is not working when turned on Check the bulbs are assembled correctly with the bulb base. Check the two wires are connect perfectly (Pic.12)
The fan wobbles when working Check the screws are tight (Pic.29) and the hanger ball sits steadily (Pic.34 &Pic.34a)
Remote control can not control the fan Check the battery is installed properly. Check the wiring of the remote receiver is correct (Pic.36)
Lampshade has warpage when assemble Please pay attention on the screw sequence when screw down. (See point 4 on Page 5)
Bulb base is loose after assembly
The extension rod tail is too long or too short, please check point 4 on page
Canopy is too small to accept the remote receiver and the wires 6
The wires are disorderly. Please keep the wires in order and squeeze a bit before you lift the canopy (Pic.37 & Pic.38).
Fan blade moves very slowly when I turn on the fan. Check the red wires connect are not diverge other wise there will be insufficient power of the fan when working. (Pic.36)