XTOOL S1 Laser Engraver User Manual
- May 15, 2024
- XTOOL
Table of Contents
XTOOL S1 Laser Engraver
Specifications
- Model : xTool S1
- Type : Laser cutter and engraver
- Processing speed : High
- Accuracy: High
- Positioning: Accurate coordinates-based positioning
- Features : Automatic focus, curved surface engraving
Product Usage Instructions
Safety First (Important)
Before using the xTool S1, it is crucial to prioritize safety. Familiarize yourself with all safety precautions and procedures outlined in the user manual. Follow these precautions strictly and ensure that the machine is properly assembled and functioning correctly.
General Safety
Read and understand all safety precautions before operating the machine. Follow these precautions diligently to ensure safe usage.
Laser Safety
The laser module of the xTool S1 is enclosed within a casing and light shield during operation. The machine also includes a safety interlock switch. If the lid is lifted while the machine is in operation, it will automatically stop working to prevent any harm to individuals.
Please note that the reference standards for laser safety are:
- American National Standard for Safe Use of Lasers (Z136.1-2022)
- International Electrotechnical Commission Standard (IEC 60825-1:2014)
- European Standards (EN 60825-1:2014/A11:2021)
Fire Safety
Never leave the xTool S1 unattended while it is in operation. Additionally, ensure that combustible materials are kept at a safe distance from the machine to prevent any fire hazards.
Electrical Safety
Take note of the following warnings and suggestions regarding electrical safety:
- Do not open any access panel on the machine when it is connected to the power supply. Accidental contact with the power supply may cause injury.
- Avoid touching any electronic areas of the machine with your hands or other tools when it is connected to a power supply.
- The power switch is located at the back of the machine. To power it on, press (-), and to power it off, press (o).
Warning and Instruction Signs
Tool S1 includes warning and instruction signs that indicate potential physical injuries or machine damage before and/or during operation. If any sign is damaged or lost, it should be replaced immediately. A template for printing these signs can be found in the user manual.
List of Items
The following items are included with the xTool S1:
Meet your xTool S1
Get acquainted with the xTool S1 laser cutter and engraver. Familiarize yourself with its components, features, and functionalities.
Use your xTool S1
Learn how to effectively use the xTool S1 laser cutter and engraver for various purposes.
Use xTool S1 with the Air Assist Set
Discover how to enhance your laser cutting and engraving experience by utilizing the xTool S1 with the Air Assist Set.
Use xTool S1 with the Riser Base
Learn how to optimize your laser cutting and engraving projects using the xTool S1 with the Riser Base.
Use xTool S1 with the Honeycomb Panel
Explore the benefits of using the xTool S1 with the Honeycomb Panel for specific laser cutting and engraving applications.
Use xTool S1 with the Rotary Attachment
Discover how to utilize the xTool S1 with the Rotary Attachment to achieve precise curved surface engraving.
Understand the Annular Indicator
Gain a comprehensive understanding of the Annular Indicator on the xTool S1 and its significance during operation.
After-sales Services
Learn about the available after-sales services provided by xTool for any assistance or support you may require.
FAQs
- Q: Where can I find the latest accessories and materials for xTool S1?
- A: You can visit our online store to find our latest accessories and various materials that can maximize the potential of your xToolS1.
- Q: How can I get technical support for my xTool S1?
- A : For technical support, you can visit our support center at support.xtool.com. You can also reach out to our technical support team via email at [email protected].
- Q: Where can I find video tutorials for xTool S1?
- A : You can find video tutorials on our YouTube channel at youtube.com/c/xToollaserbox?sub_confirmation=1.
- Q: How can I join the xTool S1 Facebook group?
- A : To join the xTool S1 Official Group on Facebook, simply search for “xTool S1 Official Group” and request to join. This group is a platform for sharing creative ideas and getting inspired by others.
- Q: How can I contact the xTool CEO?
- A : You can reach out to the xTool CEO through the official website at xtool.com.
- Q: Is there any statement or additional information I should be aware of?
- A : Yes, please refer to the Statement section in the user manual for any additional information or important statements.
Dear xTooler
- Thank you for choosing xTool S1. We are so grateful for your recognition, and sincerely hope you will enjoy it! xTool S1 is an easy-to-use powerful laser cutter and engraver with high processing speed and accuracy, supporting accurate coordinates-based positioning, automatic focus, and curved surface engraving. Whether you are a novice or an expert, whether you use it at home or for business purposes,
- xTool S1 is ready to give you the best laser engraving & cutting experience.
- Our mission is to make it easier for everyone to create with our machine. We attach great importance to product experience and user suggestions. Pleaselet us know if you have any questions anytime. We are always here to help. You can join our Facebook group to share creative ideas and get inspired by others. By visiting our online store, you can also find our latest accessories and various materials to maximize the magic of xTool S1.
Thanks again for your support, and we will consistently provide quality products and services in the future.
Sincerely,
Official website : xtool.com
Facebook group : xTool S1 Official Group
Support center : support.xtool.com
Technical support : [email protected]
Video tutorial :
youtube.com/c/xToollaserbox?sub_confirmation=1
Safety first (important)
General safety
Read and get familiar with all safety precautions and proceduresbefore using the machine. Strictly follow all safety precautions. Ensure that the machine is properly assembled and is workingproperly
Caution
Follow the operating principles:
- Check the machine for damage every time before you use it. Do not operate it in any way when any damage or defect is found.
- Ensure that the workspace is clean and flat.
- Do not disassemble the machine or change its structure in any way without authorization. Do not modify or decompile its operating system.
- Do not leave the device unattended during operation. Pay attention to whether it is working properly.
- Keep the inside of the machine clean. Residues and chippings accumulated during cutting and engraving are dangerous and may cause a fire. Clean the chippings and residues inside the workarea regularly.
- The machine works properly at the temperature of 0°C to +35°C and can be stored properly at the temperature of –10°C to +40°C. Do not operate it at a temperature lower than 0°C.
Laser safety
Generally, the laser module is completely enclosed in the casing and light shield during operation. The device has a safety interlock switch. If the lid is lifted during operation, the device will stop working and no harm will be done to people
Warning
Follow the operating principles:
-
Do not operate the machine when any part of it is removed.Removing any part may expose the laser system and cause damageto the machine.
-
Do not engrave or cut any material that contains PVC or vinyl(processing plastics is not recommended). These materials (and othermaterials containing chlorine/chloride) can generate corrosive vaporthat is extremely harmful to the human body and can cause damage to the device. Any damage caused by engraving or cutting anymaterial containing PVC or vinyl is not covered by the Company’swarranty.
o not engrave or cut any unknown materials. Vaporization ormelting of many materials, which include but are not limited to PVCand polycarbonate, may release harmful smoke. -
Laser operation is prohibited when the lid is lifted. Make sure thatthe lid is closed during operation and do not tamper with the safetymechanism of the lid.
-
Do not leave the device unattended during operation. Pay attentionto whether it is working properly.
The reference standards for laser safety are the American National Standard for Safe Use of Lasers (Z136.1-2022), InternationaElectrotechnical Commission Standard (IEC 60825-1:2014), andEuropean Standards (EN 60825-1:2014/A11:2021).
Fire safety
- A high-density laser beam is used by the device to irradiate the material to be cut or engraved, so as to heat up the material surface and vaporize the material without burning. But most materials are inherently flammable and may be ignited to form an open flame that can burn down the device (even if it is made of flame-retardant materials) and its surroundings. Experience showsthat vector cutting with a laser is most likely to produce an open flame. Inparticular, acrylic has proven to be extremely flammable in vector cutting.
Danger
Read the following warnings and suggestions carefully:
- Ensure that the workspace is well-ventilated so that the generatedsmoke can be discharged in time.
- Do not stack materials (especially organic ones, such as paper) around the machine. They may cause the spread of flames and increase the risk of material ignition.
- Do not leave the machine unattended when it is working. If the machine works with setting errors and is left unattended for a long period of time, or if a mechanical or electrical fault occurs, a fire maybe caused.
- Clean the device regularly. Excessive accumulation of residues and chippings from cutting and engraving would increase the risk of fire. The internal working area needs to be cleaned periodically to ensure that there is no residue or chipping inside the device.
- Ensure that the area around the machine is clean without any cluttered flammable materials, explosives, or volatile solvents, such as acetone, alcohol, or gasoline.
- Keep a fire extinguisher and perform regular maintenance and inspection of it.
- If a fire occurs during processing, take good care of yourself. For asmall flame, you can wait for it to go off; for a larger fire, please keep a safe distance and use a fire extinguisher to put it out.
Electrical safety
Caution
Read the following warnings and suggestions carefully :
- Do not open any access panel on the device when the device is connected to the power supply. Accidental contact with the power supply may cause injury.
- Do not touch any electronic area with your hands or other tools when the machine is connected to a power supply.
- The power switch is on the back of the device. Press (-) to power it on and press (o) to power it off.
Warning and instruction signs
On xTool S1, the warning and instruction signs are labeled where physical injuries or damage to the machine may be caused before and/or during operation. If a sign is damaged or lost, replace it immediately. You can use the following template to print the sign you need.
List of items
The following items are included only in some packs.
Meet your xTool S1
Preparations
Use your xTool S1
Scan the QR code to find example projects and tutorials. Alternatively, you can visit support.xtool.com and click xTool S1 to view example projects and tutorials.
xTool S1 is delivered with a material pack that allows you to start your creation
Emergency stop
If an emergency occurs, you can press the emergency stop switch to shut off the machine.
After dealing with the emergency, you can turn the emergency stop switch to reset it.
Operation access control
Use xTool S1 with the air assist set
Airflow adjustment
Replace the filter
If the pack you purchase does not include the air assist set, you need to purchase one before using it
Replace the filter
Use xTool S1 with the riser base
Use xTool S1 with the honeycomb panel
Use xTool S1 with the rotary attachment
- The rotary attachment needs to be used together with the riser base on xTool S1. If the pack you purchase does not include the rotary attachment or riser base, you need to purchase them before using them. With the rotary attachment, you can use xTool S1 to process cylindrical materials
After-sales services
- For technical support, contact us at [email protected].
- For more information about after-sales services, visit support.xtool.com.
FAQs
- Do I need to clean the laser module? If yes, how often? Yes, you need to clean the laser module regularly. Laser processing often produces a large amount of smoke, which may cause the lens protector to get dirty or block the nozzle. If you do not clean the laser module in a timely manner, the laser power may be reduced and the laser module may be damaged.
For more information on how to clean the laser module, scan the QR code to watch the video.
Cleaning steps
- Turn off the machine and remove the laser module from the machine.
- Remove the nozzle and lens protector one by one from the laser module.
- Clean the laser lens, lens protector, and nozzle one by one with a lint-free cloth moistened with alcohol. For more information on how to clean the laser module, scan the QR code to watch the video
Without the air assist set, you are advised to clean the laser module at the following frequencies:
- 10 W laser module : clean it after every 2 hours of processing
- 20 W laser module : clean it after every 1 hour of processing
- 40 W laser module: clean it after every 0.5 hours of processing
Without the air assist set, you are advised to clean the laser module at the
following frequencies
2. The smoke is exhausted slowly. Why?
Too much dust accumulates on the exhaust fan. Possible cause:
- Turn off the machine and remove the louver or smoke exhaust pipe from the machine.
- Clean the exhaust fan with a tissue or cotton swab moistened with clean water or alcohol.
- Install the louver or smoke exhaust pipe back to the machine.
Otherwise, laser beams may leak out, and your hands may get hurt if touching the fan. Solution: With the air assist set, you can clean the laser module at a lower frequency.
The distance sensor does not work in auto focus. What can I do?
Possible causes:
- The initialization of the distance sensor fails due to improper installation or early firmware version, and the probe doesn’t extend.
- The probe of the distance sensor cannot move smoothly due to hardware faults.
- The material is too thick or thin, and the material surface to be processed is out of the focusing range.
- On a curved material, the probe may slip in a part with a steep angle, causing a distance measurement failure.
- The laser module cannot execute the distance sensing function.
Solution
- Check whether the probe of the distance sensor extends during auto focus. If no, try to reinstall the distance sensor. If the probe still fails to extend, try to update the firmware to the latest version.
- Remove the distance sensor and check whether its probe can move smoothly. If no, please contact our after-sales service to replace the distance sensor.
- Refer to the user manual and use a processing way applicable to your material thickness.
- For a curved material, you can try to adjust the processing area to a flatter one, so that the probe can measure the distance in a flatter area.
- If the distance sensor still fails to measure distance, please contact our after-sales service. Before the problem is solved, you can measure the distance manually. For more information on how to measure the distance, see support.xtool.com.
The software prompts that the baseplate is not installed properly. What can I do?
Possible cause
The screws securing the baseplate are loose.
Solution
- Tighten all the screws to keep the baseplate in place.
Statement
- Thank you for choosing xTool products! If you use the product for the first time, read carefully all the accompanying materials of the product to improve your experience with it. If you do not use the product according to the instructions and requirements of the Manual, or mis-operate the product due to misunderstanding, etc., the Company shall bear no responsibility for any loss resulting therefrom.
- The Company has collated the content of the Manual rigorously and carefully, but errors or omissions may remain. The Company is committed to continuously improving product functions and service quality, and therefore reserves the right to change any product or software described in the Manual and the content of the Manual at any time.
- The Manual is intended to help you use the product properly and does not include any description of hardware and software configuration. For product configuration, refer to the related contract (if any) and packing list, or consult your distributor. Images in the Manual are for reference only and the actual product may vary. Protected by copyright laws and regulations, the Manual shall not be reproduced or transcribed in any way, or be transmitted on any wiredor wireless network in any manner, or be translated into any language, or be modified in any way, such as content, image, or layout modification, without the prior written authorization of the Company.
- The Company is committed to continuously improving the product and related materials. The product and the Manual are subject to change, and updates can be found at xtool.com
DECLARATION OF CONFORMITY
- Hereby, Makeblock Co., Ltd., declares that this product is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU and the RoHS directive 2011/65/EU & (EU) 2015/863.
FCC statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body
References
- LightBurn Software
- xTool Support Center
- Smart Desktop Laser Cutter and Engraver | xTool Laser
- xTool Creative Space: Software Download for All xTool Machines