GYS NBT 100 Battery Tester Instruction Manual

GYS NBT 100 Battery Tester

SAFETY INSTRUCTIONS

| This manual includes guidelines on the operation of your device and the precautions to follow for your own safety. Ensure it is read carefully before first use and keep it handy for future reference.
---|---
| Risk of explosion and fire!
A battery being charged can emit explosive gas
| The battery tester should only be connected to batteries with a rated output voltage of 12 V.
| CAUTION: Reverse polarity will cause the fuse to blow and could cause permanent damage. Damage due to reverse polarity is not covered by our warranty.
| CAUTION: If the car’s battery is disconnected, some management systems may be disabled.
| Consult your vehicle manual for more information on installation.
| Do not use the battery tester if the cord or terminals are damaged.
| Do not use the battery tester if it has received a severe shock or has been damaged in any way
| Do not disassemble the device. Incorrect reassembly may result in a risk of electric shock or fire.

Acid projection hazard!

|

• Wear appropriate safety glasses and clothing

---|---
|

• If your eyes or skin come into contact with battery acid, rinse the affected part of the body with plenty of water and seek immediate medical assistance.

|

• Avoid flames and sparks. Do not smoke. • Protect the electrical contacts of the battery against short-circuiting.

|

• The device complies with European Directive. • The certificate of compliance is available on our website.

|

• EAC conformity mark (Eurasian Economic Commission)

|

• Material conforms to UK requirements. The UK Declaration of Conformity is available on our website (see cover page).

|

• Device compliant with Moroccan standards.
• The Cم) CMIM) declaration of conformity is available on our website

|

• This product should be disposed of at an appropriate recycling facility. Do not dispose of in domestic waste.

|

• Recyclable product that falls within waste sorting recommendations

CONNECTING THE BATTERY TESTER

1. Make sure that the area is well ventilated before performing a test.
2. Tester for 12 V batteries.
3. Before running a test on the battery, ensure that the ignition and the consumers are switched off. Close all the doors and the boot.
4. Make sure that the battery connections are clean. If necessary, clean them using a wire brush.
5. Any presence of oxidation between the tester terminals and the battery connectors or between the battery connectors and the battery terminals reduces the effectiveness of the tester.
6. Connect the negative plug (black) to the negative terminal of the battery. Connect the positive plug (red) to the positive terminal of the battery

BATTERY TEST

1. The screen lights up and displays the battery voltage. Press the «ENTER» key to continue.
2. Select the battery type (Standard liquid battery or Sealed battery: VRLA/GEL/ AGM) using the arrow buttons and press «ENTER» to confirm.
3. Select the standard (marked on the battery) using the arrow buttons and press «ENTER» to confirm. (Standard : CA, MCA, DIN, IEC, EN, SAE)
4. Enter the starting current indicated on the battery («A») and confirm.
5. If the display shows «CHA», specify whether or not the battery is charged using the arrows and confirm with «ENTER».
6. One of the results below is displayed.

Battery test result

good condition but low state of charge.
****CHARGE & TEST| Yellow and red light XXXX (CCA value)| Recharge the battery and perform the test again. If the result remains the same, replace the battery.
TO BE RE- PLACED| Red light XXXX (CCA value)| The battery is coming to the end of its life. A replacement should be organised.
ERROR| ERR in red on the screen| The battery is higher than 1200 CCA (SAE) or a problem at the cell level is found (short circuit…). Re- place the battery.

WARRANTY

The warranty covers faulty workmanship for 2 years from the date of purchase (parts and labour).

The warranty does not cover:

• Transit damage.
• Normal wear of parts (eg. : cables, clamps, etc..).
• Damages due to misuse (power supply error, dropping of equipment, disassembling).
• Environment related failures (pollution, rust, dust).

In case of failure, return the unit to your distributor together with:
– The proof of purchase (receipt etc …)
– A description of the fault reported

JBDC

1, rue de la Croix de Landes – CS54159
53941 Saint-Berthevin Cedex
France

Documents / Resources

| GYS NBT 100 Battery Tester [pdf] Instruction Manual
NBT 100 Battery Tester, NBT 100, Battery Tester, Tester
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>