elk Lighting 6931714 72 Wide 14 Light Linear Chandelier Instruction Manual
- June 16, 2024
- Elk Lighting
Table of Contents
ANY QUESTIONS CALL:800-613-3261
M-F 8:00AM-6:00PM ET
6931714 72 Wide 14 Light Linear Chandelier
ITEM#: 69317/14
ITEM#: 69327/14
WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING:
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended. Before assembly, remove all parts and part packages from box. If
anything is missing, please contact the retailer from which the product was
purchased.
-
Carefully pull house wires out of junction box so they are easily accessible during installation.
-
Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.
-
Carefully pull house wires through center hole in mounting bracket (A). Align small holes in mounting bracket (A) with holes in junction box.
-
Thread each junction box screw (B) into appropriate hole in mounting bracket (A) and into hole in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
CAUTION: Make sure house wires are pulled completely through hole in mounting bracket. DO NOT pinch wires between mounting bracket and ceiling. -
Using hex wrench (N), loosen screws on U-shaped straps on fixture body (O).
-
Insert bottom ends of rod (M) into openings on U-shaped strap on fixture body (O). Tighten screws to secure rod (M) in place.
-
Repeat step 5 and 6 for remaining rod (M).
-
Attach one locking link (G) onto end of each rod (M).
-
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height. Ensure chains are of equal length.
-
Slip chain link at end of chain (H) onto locking link (G) on top of each rod (M).
-
Weave fixture wires through chain links, skipping every other chain link.
-
Push fixture wires through hole in canopy (D).
-
Attach second chain link to end of each section of chain (H) and to each loop on canopy (D).
-
Strip 3/4” of insulation from ends of fixture wires.
-
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire (copper) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire. -
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
-
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
-
Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
-
Carefully raise fixture up to ceiling. Place canopy (D) of fixture over mounting bracket (A). Pass holes in canopy (D) over ends of fixture mounting screws (E).
-
Screw one threaded cap (F) onto end of each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.
-
Screw recommended bulbs (E26 Edison bulb type, not inacluded) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>