CRUX SWRTY-61N Wiring Interface User Manual
- June 16, 2024
- CRUX
Table of Contents
CRUX SWRTY-61N Wiring Interface
Product Information
Interfacing Solutions – Radio Replacement SWC Retention SWRTY-61N
Radio Replacement with Steering Wheel Retention and Rear-View Camera Retention for TOYOTA Vehicles
Product Features:
- Allows for radio replacement while retaining steering wheel controls (SWC) and rear-view camera functionality
- Designed specifically for TOYOTA vehicles
Parts Included:
- SWRTY-61N Module
- SWRTY-61N Harness
- USB Retention Cable
- SWC Cable
- +12V Constant, +12V ACC, Ground, Illumination, Right Front (+/-), Left Front (+/-), Right Rear (+/-), Left Rear (+/-), Vehicle Speed Sense (VSS), Reverse Trigger, Parking Brake, and Power Antenna wires
- Red/White RCA Audio Input
- Yellow RCA (Retain OE Camera)
- Rear View Camera Signal 12-Pin Black Connector
- USB-TY01 USB Retention Adaptor (included in kit)
- Antenna Adaptor
Installation Diagram:
Specifications:
- Module: SWRTY-61N
- Cable Type: SWC Cable, USB Retention Cable
- Connector Types: 24-Pin, 12-Pin Black, 28-Pin
Product Usage Instructions
Step 1: Installation
- Refer to the installation diagram for proper wiring connections.
- Connect the SWRTY-61N harness to the vehicle’s factory harness.
- Connect the SWC cable to the 4-pin port on the module.
- Connect the USB retention cable to the module and the aftermarket radio.
- Connect the RCA audio input cables to the aftermarket radio.
- Connect the rear view camera signal cable to the module and the aftermarket radio.
- Insulate or cap any unused wires or connectors.
Step 2: DIP Switch Settings
Aftermarket Radio DIP Switch Settings:
- Refer to the DIP switch settings chart for your specific radio brand.
- Set the DIP switches on the SWRTY-61N module according to your aftermarket radio brand.
Toyota Steering Wheel Control DIP Switch Setting:
- Set DIP switch 5 and 6 to ON for Toyota vehicles.
- Refer to the SWC module on radio vehicle diagram for DIP switch positions.
Frequently Asked Questions (FAQ)
Q: Can I use this product with any aftermarket radio?
A: Yes, this product is compatible with most aftermarket radios. Please
refer to the DIP switch settings chart for your specific radio brand.
Q: How do I retain the factory AUX input in my vehicle?
A: The SWRTY-61N module retains the factory AUX input in select 2007-Up
vehicles. Simply connect the red/white RCA audio input cable to the
aftermarket radio.
Q: Where should I connect the blue antenna turn-on wire?
A: The blue antenna turn-on wire should only be connected to one circuit
of the aftermarket radio. Choose the one which has a wire populated on the
factory connector side.
Q: How do I set up the steering wheel controls?
A : For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream,
and most off-brand radios, check the aftermarket radio’s manual to see if the
SWC buttons need to be programmed. For Toyota vehicles, set DIP switch 5 and 6
to ON.
SWRTY-61N
Radio Replacement with Steering Wheel Retention and Rear-View Camera Retention
for TOYOTA Vehicles
PRODUCT FEATURES
- Retains factory features in select Toyota vehicles while functioning with an aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- iPhone Voice Recognition (VR) feature from SWC on select radios.
- Retains OEM Rear View Camera.
- Retains factory USB and auxiliary audio input (aftermarket radio must have these features).
- Includes factory USB retention adapter cable.
- Supports BT-HF/A2DP/AVRCP profile on select aftermarket radio models.
- Supports Pick Up/End Call, Pick up and Toggle between 1st and 2nd incoming call, AVRCP Track, Seek.
- EIA color coded wiring for easy installation.
PARTS INCLUDED
INSTALLATION DIAGRAM
SPECIAL NOTE
On 2013 Toyota Sequoia and Tundra, the parking brake wire (RED wire) is in
position#1 on the OEM 28-pin connector. Please insert the YELLOW/BLACK wire on
the SWRTY-61N harness into position#1. For all other models, please insert
into position# 15.
Please check that you are inserting the pin into the correct location as it is
difficult to remove it again. The locking tab of the pin should be facing UP
when it is inserted into the connector.
DIP SWITCH SETTINGS
AFTERMARKET RADIO DIP SWITCH SETTINGS
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most off-brand radios,check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
TOYOTA STEERING WHEEL CONTROL DIP SWITCH SETTING:
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
NOTE: Insulate the Blue/Yellow wire or the 3.5mm plug if not being used.
For aftermarket radios that have wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable and connect the SWC wires as follows:
Note that there are some radios that only have SWC1 and SWC2, in this case “shield” does not need to be connected.
24 TO 16 PIN ADAPTER
Some vehicles do not have the 24-Pin Video Input connector. Instead, they have a 16-Pin connector that controls the video input for the camera. Use the optional adaptor and connect to the T-harness to convert the harness to work with the 16-Pin connector style.
VEHICLE APPLICATIONS
SCION| | TOYOTA|
---|---|---|---
2012 – 2016| FRS| 2012 – 2019| 4Runner
2016| iM| 2012 – 2018| Avalon
2012 – 2013| iQ| 2012 – 2017| Camry
2012 – 2016| tC| 2012 – 2017| Corolla
2012 – 2015| xB| 2013 – 2018| Highlander
2012| xD| 2012| Matrix
| | 2012 – 2017| Prius
| | 2012 – 2018| RAV4
| | 2012 – 2018| Sequoia
| | 2015 – 2017| Sienna
| | 2013 – 2019| Tacoma
| | 2013 – 2019| Tundra
| | 2012 – 2015| Venza
Note: See Special Note on page 2.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: 818-609-9299 • fax:
818-996-8188 •
www.cruxinterfacing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>