makita 6305 Drill Instruction Manual
- June 9, 2024
- Makita
Table of Contents
makita 6305 Drill
Explanation of general view
- Lock button
- Switch trigger
- Indicator lamp
- Tool barrel
- Side grip (auxiliary handle)
- Bit
- Chuck
- Chuck key
- Depth gauge
- Stopper holder
- Concave
- Convex
- Protrusions
- Teeth
- Limit mark
- Screwdriver
- Brush holder cap
SPECIFICATIONS
Model | 6305 |
---|---|
Capacities | Steel |
Wood | 30 mm |
No load speed (min-1) | 1,450 |
Overall length | 346 mm |
Net weight | 2.8 kg |
Safety class | /II |
- Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment. Be sure that you understand their meaning before use.
Read instruction manual.
DOUBLE INSULATION
Intended use
The tool is intended for drilling in wood, metal and plastic.
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on single-phase AC
supply. They are double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
-
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
-
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
-
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety -
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
-
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
-
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
-
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
-
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
-
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
-
Use of power supply via a RCD with a rated residual current of 30mA or less is always recommended.
Personal safety -
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Power tool use and care -
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
-
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service -
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
-
Follow instruction for lubricating and changing accessories.
-
Keep handles dry, clean and free from oil and grease.
DRILL SAFETY WARNINGS
-
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations. -
Hold the tool firmly.
-
Keep hands away from rotating parts.
-
Do not leave the tool running. Operate the tool only when hand-held.
-
Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
-
Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
WARNING:
DO NOT let comfort or familiarity with product (gained from repeated use)
replace strict adherence to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
- Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.
Switch action (Fig. 1)
CAUTION:
- Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then push in the lock button.
To stop the tool from the locked position, pull the switch trigger fully, then release it.
Indicator lamp (Fig. 2)
The green power-ON indicator lamp lights up when the tool is plugged to the
mains. If the indicator lamp is lit but the tool does not start even if the
tool is switched ON, the carbon brushes may be worn out, or the motor or the
switch may be defective. If the indicator lamp does not light up, the mains
cord or the indicator lamp may be defective. When the mains cord is defective,
the tool neither starts nor lights the indicator lamp. When the indicator lamp
is defective, the tool starts without the indicator lamp lighting up.
ASSEMBLY
CAUTION:
- Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing side grip (auxiliary handle) (Fig. 3)
CAUTION:
- Always be sure that the side grip is installed securely before operation.
Screw the side grip on the tool barrel securely.
For work with a side grip at the other different angles, another type of side grip (auxiliary handle) is available as an optional accessory. Follow the installation procedure below.
Installing or removing drill bit (Fig. 4)
To install the bit, place it in the chuck as far as it will go. Tighten the
chuck by hand. Place the chuck key in each of the three holes and tighten
clockwise. Be sure to tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in just one hole, then
loosen the chuck by hand.
After using the chuck key, be sure to return to the original position.
Depth gauge
The depth gauge is convenient for drilling holes of uniform depth.
Loosen the side grip and remove it. Fit the convex on the stopper holder to
the concave on the tool barrel. Insert the side grip into the stopper holder
and screw the side grip. (Fig. 5)
Insert the depth gauge into the hole in the stopper holder. Adjust the depth
gauge to the desired depth and then tighten the side grip firmly. (Fig. 6)
Side grip assembly (optional accessory) (Fig. 7)
Install the side grip assembly so that the teeth on the grip fit in between
the protrusions on the tool barrel.
Then tighten the grip by turning clockwise at the desired position. It may be
swung 360° so as to be secured at any position.
NOTE:
- The depth gauge cannot be used at the position where the depth gauge strikes against the tool body.
OPERATION
Holding tool (Fig. 8 & Fig. 9)
When drilling a large hole with a hole saw, etc., the side grip (auxiliary
handle) should be used as a brace to maintain safe control of the tool.
Grasp the rear handle and the front grip firmly when starting or stopping the
tool, since there is an initial and final reaction.
When drilling action is forward (clockwise), the tool should be braced to
prevent a counterclockwise reaction if the bit should bind. When reversing,
brace the tool to prevent a clockwise reaction. If the bit must be removed
from a partially drilled hole, be sure the tool is properly braced before
reversing.
Drilling operation
Drilling in wood
When drilling in wood, the best results are obtained with wood drills equipped
with a guide screw. The guide screw makes drilling easier by pulling the bit
into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make an indentation
with a center-punch and hammer at the point to be drilled. Place the point of
the bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The exceptions are iron and
brass which should be drilled dry.
CAUTION:
- Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool.
- There is a tremendous twisting force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
- A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly.
- Always secure small workpieces in a vise or similar hold-down device.
- Avoid drilling in material that you suspect contains hidden nails or other things that may cause the bit to bind or break.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
- Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. (Fig. 10)
Use a screwdriver to remove the brush holder caps. Take out the worn carbon
brushes, insert the new ones and secure the brush holder caps. (Fig. 11)
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
- These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Drill bits
- Hole saws
- Chuck key
- Grip assembly
- Depth gauge assembly
NOTE:
- Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Corporation
Anjo, Aichi, Japan
www.makita.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>