eMoMo ICPTRWS ICP Multifunction Cup Holder Instruction Manual
- June 16, 2024
- eMoMo
Table of Contents
ICP multifunction cup holder
ICPTRWS ICP Multifunction Cup Holder
Installation instruction
Step 1 Screw two M8 screws into the product
Step 2
Make holes in the corresponding position of the sofa board
（Opening size L199*W115mm）
Step 3
Install the product into the hole
Step 4
Install gasket and butterfly nut and twist tightly
Operating instruction
-
Connect the 29V2A power supply to power ups the product.
-
This product has 8 touch buttons and 1 mechanical button. The operation all button is as follows
This mechanical button is the power button. After pressing this button, all functions are turned off (including wireless charging and USB charging) and all button lights are off. Pressing it again to turn on the power, all functions are restored and all touch button lights are blue.
Long press this button to open the seat actuator.
Long press this button for the head actuator, waist actuator and seat actuator are all recovered.
Long press this button to extend the waist actuator.
Long press this button for waist actuator retraction.
Long press this button to extend the head actuator.
Long press this button for head actuator retraction.
Short press this button to open the flip cover, short press again to close the flip cover.
Long press this button to lock other touch buttons. After the lock, the other touch button lights are off and the touch control is invalid. The lock button lights turn red，Long press again to unlock, all touch button functions are restored and the button light turns blue. -
After the flip cover is opened, there is a slot for wireless charging. Put the phone in the slot to start wireless charging. When placing the phone, the back of the phone should face the inclined plane, otherwise it cannot be charged，When charging, there will be a prompt tone and the power button will change from blue light to green light. If there is no prompt tone and light indication, please check whether the mobile phone is correctly placed.
-
After the flip cover is opened, the middle round hole is the cup holder placement area.
-
There is a USB quick charging port in the middle of the touch button, and there is a sliding dust cover, please close the slide cover when you don’t charging to avoid dust.
Specification
Input:29V2A USB output:18W Wireless charging output:5W Rated power:58W
Notes
- The flip cover of the product may pop slightly during transportation due to shock and other factors, which is normal. This phenomenon does not occur after power on and the flip cover is opened and closed once.
- When the product is powered on, do not operate the flip cover opening and closing button frequently when it is running, so as to avoid frequent and rapid steering that may lead to overheating and damage of the internal motor, thus reducing the service life of the product.
- If the flip cover is in the half-open or half-closed state due to manual press, idling or incomplete closure will occur when operating the flip cover opening and closing button, which is a normal phenomenon. It can be restored by pressing the flip cover button once more to make it open and closed fully.
- The appearance of this product adopts wire drawing process, do not scratch the surface with sharp objects.
- To ensure the service life of the flip cover, do not manually flip or press the flip cover.
- Tear off the protective film on the inside of the cover when you use it.
- Please be careful of small items (such as steel needles) or liquid entering the wireless charging tank. If liquid enters the wireless charging tank accidentally, please immediately turn off the power and power off, remove the extractable inner box, and restart it after the liquid dries. Check whether small items fall into the inner box. If they fall into the bottom, contact the manufacturer.
- Please close the electric flip cover and USB dust cover when the product is not in use.
- If buttons fail or the flip cover is stuck, power off the device for 2 minutes and restart it.
- Children should be used under the supervision of parents.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>