VORTEX VTK-1080 Mechanical Keyboard User Manual
- June 16, 2024
- VORTEX
Table of Contents
ONE 4
VTK-1080 Mechanical Keyboard
User Manual
VTK-1080 Mechanical Keyboard
Product Name: Mechanical Keyboard
Model Name: VTK-1080
Product Size:
LWH: 44.0°13.5*3.0 cm + 0.3
Turn on the power switch, hold down Fn + 3/ 4/5
for three seconds to enter pairing mode. The device will display ONE4#1 / 2/3,
and once confirmed, the pairing is complete. During the process, LED1 / 2/3
indicator lights will sequentially flash yellow light.
Battery: Lithium battery
Working Current: 9mA —— Release the key will enter into standby mode
Standby Current: 4mA —— Hibernate for 30 minutes will enter into sleep
mode
Sleep Current: 0.7mA (Bluetooth will be disconnected)
Rated Input Power: 5V ****500mA
Press Fn + P to check the battery level
66%-100%: LED1, 2, and 3 flash red light for two seconds
33%-66%: LED1 and 2 flash red light for two seconds
Below 33%: LED1 flashes red light for one second
Low battery indication
(appears when any key is pressed) : LED2 flashes red light
Unable to charge : LED1, 2, and 3 flash red light in sequence| Fn
Switching
Can only be used in (2/3 / 4 layer)
Simultaneously press Caps Lock, L_Ctrl, and
R_Win to enter Fn setting mode (flashing white
light). At this time, the first key pressed is the
Fn key (Ins / Enter / Shift cannot be used as Fn,
and macro is not available in the Fn layer).| Press Fn + X to view the
current channel
LED1 =1, LED2 =2, LED3 = 4
Channel 1 : LED1 flashes yellow light for two seconds
Channel 2 : LED2 flashes yellow light for two seconds
Channel 3 : LED1 and LED2 flash yellow light for two seconds
Channel 4 : LED3 flashes yellow light for two seconds
Channel 5 : LED1 and LED3 flash yellow light for two seconds
---|---|---
This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be u sed in portable exposure condition without restriction.
TECHNICAL SUPPORT
vortexkeyboard.ts@gmail.com
CUSTOMER SERVICE
vortexkeyboard.cs@gmail.com
OFFICIAL WEBSITE
www.vortexgearstorehttps://vortexgear.store/
Company Name: Vortexgear Co., Ltd.
Company Address : 4F., No. 14, Ln. 181, Sec. 2, Jiuzong Rd., Neihu Dist.,
Taipei City, 114709, Taiwan
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>