Tenda AX3000 Dual Band Gigabit Wifi 6 Router Installation Guide

Tenda AX3000 Dual Band Gigabit Wifi 6 Router Installation Guide

Connect the router

The “new router” and “router” in this guide refer to the router in the package.

Step 1: Import your PPPoE user name and password into the new router (Optional)

Tips
This function is only applicable when the connection type of the original router is PPPoE, except for PPPoE of some specialists’ or Pepo connection set up manually with VLAN Information.

1. Power on your original and new routers.
2. Connect the WAN port of the original router to a LAN port (1, 2 or IPTV/3) of the new router using an Ethernet cable. After the LED indicator of the new router blinks fast for 8 seconds, the PPPoE user name and password are imported to your new router.
3. Remove the original router

Step 2: Connect the WAN port of the router

1. Ensure that the router is powered on.
2. Connect the WAN port of the router to the LAN port of your modem or the Ethernet jack using an Ethernet cable. The LED indicator blinks fast for 3 seconds.

Connect your device to the router

Option A: Connect your WiFi-enabled device, such as a smartphone, to the wireless network of the router. You can find the default WiFi network information on the bottom label of the router.

Option B: Connect your wired device, such as a computer, to a LAN port (1, 2 or IPTV/3) of the router using an Ethernet cable. The LED indicator blinks fast for 3 seconds.

Set up the router

1. Start a web browser on the device connected to the router, and visit tendawifi.com. Click Start.
   
   Tips
   If the above page does not appear, refer to Q1 in FAQ.

2. The router detects your connection type automatically.

   • If you have imported your PPPoE user name and password into the router, click Next.
   • If you did not import your PPPoE user name and password into the router, select the ISP Type based on your region and ISP and enter required parameters (if any). Click Then, click Next.
     
     

3. Set the WiFi name, WiFi password and Login password for the router. Click Next.
   

Tips
The WiFi password is used to connect to the WIFI network, while the login password is used to log in to the web Ul of the router.

Done

To access the internet with:

• WiFi-enabled devices: Connect to the WiFi network using the WiFi name and password you set
• Wired devices: Connect to a LAN port (1, 2 or IPTV/3) of the router using an Ethernet cable.

Tips
If you still cannot access the internet after the configuration, refer to Q2 in FAQ.

LED indicators

connected to the internet.
Blink slow| The router is not connected to the internet.
Blink fast for 3 seconds| A device is connected to or disconnected from an Ethernet port of the router.
Blink fast for 2 minutes| The router is pending for or performing WPS negotiation.
Off| The system is faulty, or the router is not powered on properly.

Jack, ports and buttons

to a power source for power supply.
WPS/RST| Used to start the WPS negotiation process, or to reset the router.

• WPS: Through the WPS negotiation, you can connect to the WiFi network of the router without entering the password. Method: Press the button, and the LED indicator blinks fast. Within 2 minutes, enable the WPS function of the other WPS-supported device to establish a WPS connection.
• Reset: When the router is working normally, hold the button down for about 8 seconds, and then release it when the LED indicator blinks fast. The router is reset.

WAN| 10/100/1000 Mbps auto-negotiation WAN port.Used to connect to a modem or the Ethernet jack using an Ethernet cable for internet access.
1,2| 10/100/1000 Mbps auto-negotiation LAN port.Used to connect to computers, switches or game machines, etc.
IPTV/3| 10/100/1000 Mbps auto-negotiation LAN/IPTV port.It is a LAN port by default. When the IPTV function is enabled, it can only serve as an IPTV port to connect to a set top box.

Scan QR code to download Tenda WiFi App

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>