AUDIOTEC FISCHER HEC Extension Card Bluetooth HD Input Module Instruction Manual
- June 4, 2024
- AUDIOTEC FISCHER
Table of Contents
AUDIOTEC FISCHER HEC Extension Card Bluetooth HD Input Module
Congratulations!
Dear Customer,
congratulations on your purchase of this high-qual ity HELIX / MATCH EXTENSION
CARD. We developed the BT HD based on state-of-the-art engineering and this is
reflected in its exceptional quality and the impressive use of sophisticated
technologies.
We hope you enjoy using this product.
Yours,
AUDIOTEC FISCHER
General installation instructions
For HELIX / MATCH components
To prevent damage to the unit / module and possible injury, read this manual carefully and follow all installation instructions. This product has been checked for proper function prior to shipping and is guaranteed against manufacturing defects.
Before starting your installation, disconnect the battery’s nega-tive terminal and all cables from the device to prevent damage to the unit / module, fire and / or risk of injury. For a proper perfor-mance and to ensure full warranty coverage, we strongly recommend to get this product installed by an authorized HELIX / MATCH dealer.
Install the Extension Card only in the designated device and its specific slot. Using the module in other devices or slots can re-sult in damage of the Extension Card, the device, the head unit / radio or other connected devices!
Technical data
Status LED of BT HD
Mounting information
-
First disconnect all cables from the device.
-
Depending on the device there are two possibilities to get access to the Extension Card slot.
1. Bottom plate is bolted: untighten the screws of the bottom plate and remove it. Afterwards dismantle the appropriate side panel by removing its screws.
2. Bottom plate is not bolted: dismantle the appropriate side panel by removing its screws and pull out the bottom plate sideways. -
Remove the nut and the washer from the antenna socket of the Extension Card.
-
Insert the Extension Card into the specific slot of the device which is marked in the following picture (the picture representatively dis-plays the Extension Card slot of the HELIX DSP.3). The exact position of the slot can be found in the manual of each device.
-
Make sure that the module is installed properly and all pins are fully inserted into the socket:
-
If the bottom plate was bolted, fix the new side panel which is delivered with the Extension Card. Afterwards reinsert the bottom plate and fix it, too. Otherwise reinsert the bottom plate and fix the new side panel with the screws.
-
Put the washer and the nut on the antenna socket and bolt it to the side panel.
Caution: Do not overtighten the nut as this may damage the socket !
-
Reconnect all cables to the device.
Signal routing of the Extension Card
As soon as the Extension Card is installed, it is automatically detect-ed by
the device. Now you can allocate the Extension Card to the desired outputs in
the “HEC (MEC) / AUX Routing” matrix.
Several new features are visible in the DSP PC-Tool after installing an Extension Card.
Pairing of the Extension Card with other Bluetooth® devices
The HEC / MEC BT HD module supports the A2DP profile featur-ing Qualcomm®
aptX™, Qualcomm® aptX™ HD and AAC codec for maximum sound performance. The
digital Bluetooth® data stream in I²S format is directly fed into the DSP
without any additional signal conversion. A one-time pairing procedure is
mandatory to establish a connection between the HELIX / MATCH device and your
device with Bluetooth® wireless technology. Make sure that the Bluetooth®
function on your device has been activated before you start the pair-ing
process.
Important: The Status LED of the HEC / MEC BT HD module flash-es
alternately blue and red. After three minutes the pairing mode is left
automatically if the connection has not been established.
Option a)
Turn on the HELIX / MATCH device and push the “control” button for less than 1
sec. in order to start the pairing mode.
Option b)
Start the pairing mode in the DSP PC-Tool software:
After the pairing mode is activated the Bluetooth® network can be found under
the name “ATF BT HD”.
Option c)
Start the pairing process through the CONDUCTOR or DIRECTOR remote control.
DIRECTOR: Go to the Bluetooth® Connect menu and push the “Pair” button.
CONDUCTOR: Switch to a Volume Control or Bluetooth Playback control menu
and press the rotary knob for more than 5 seconds.
WIFI CONTROL: Go to the HEC / MEC menu and push the “Pair” button under
the Bluetooth® Connect section.
Further information will be found in the corresponding user manual.
The HEC / MEC BT HD module can be paired with up to eight Bluetooth® devices.
As soon as you try to pair a ninth device, the first one will be erased
automatically from the pairing list.
The optical SPDIF output of the HEC / MEC BT HD module
The installation of the Extension Card adds as well an additional digital
optical SPDIF output to your device. This output allows to transmit any
unprocessed input or DSP-processed output signals to other devices.
A new matrix “Digital Output Routing” appears in the “Input and Out-put
Configuration” page in which you can make your desired settings.
The digital output delivers an uncoded stereo PCM signal with either 96 kHz / 24 Bit or 48 kHz / 24 Bit, depending on the sampling rate of the designated device.
Wireless DSP tuning – only DSP devices with ACO
The HEC / MEC BT HD also offers a wireless configu- ration of the DSP via the
DSP PC-Tool V5 software and a PC with Bluetooth® wireless technology for all
DSP devices equipped with ACO platform.
Therefore follow the subsequent steps:
- Pair your HEC / MEC BT HD with your PC as explained on the left side.
- Start the DSP PC-Tool software (version 5.0 or higher required).
- Toggle the connect type button, located at the right side naviga-tion, to “BT”. The software now automatically detects the device.
- Select the device which should be configured and click the “Con-nect” button. You can now start your configuration.
Warranty disclaimer
The warranty service is based on the statutory regulations. Defects and damage caused by overload or improper handling are excluded from the warranty service. Any return can only take place following prior consultation, in the original packaging together with a detailed description of the error and a valid proof of purchase. Technical modifications and errors excepted! We accept no liability for damage to the vehicle or device defects caused by the incorrect operation of the device. This product has been issued a CE marking. This means that the device is certified for use in vehicles within the European Union (EU).
Legal notes:
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its
subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in
the United States and other countries. aptX is a trademark of Qualcomm
Technologies International, Ltd., registered in the United States and other
countries. The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Audiotec Fischer GmbH is
under license. Other trademarks and trade names are those of their respective
owners.
ADDRESS: Hunegraben 26 · 57392 Schmallenberg · Germany
Tel.: +49 2972 97880 ·
E-mail: contact@audiotec-fischer.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>