busch muller Secuzed E Brex Rear Light Instruction Manual

: June 16, 2024
: busch muller

Table of Contents

busch muller Secuzed E Brex Rear Light
Product Information
Assembly Diagram
Instructions and Safety Information
Security Information

busch muller Secuzed E Brex Rear Light

Product Information

Product Overview

The Busch + Müller Secuzed E Brex is a bicycle rear light with brake light and emergency brake light function, approved for bicycles with pedal assistance systems (E-Bikes) and not approved for vehicles requiring registration (quick E-Bikes). The Type No. is 333.

Specifications

Type No.: 333
Model: Secuzed E Brex
Dimensions: 5 x 12 x 3 cm

Company	Busch + Müller KG
Address	Auf dem Bamberg 1, 58540 Meinerzhagen, Germany
Phone	+49 2354 915-6000
Email	info@bumm.de
Websites	Home – Busch + Müller EN

Busch + Müller KG

Components

Z-Reflector
LED-Ring
Sliding socket
Bracket
Connection cable
Brightness-Sensor

Assembly Diagram

An exploded view diagram shows the arrangement and orientation of the rear light’s components including the Z-Reflector, LED Ring, Sliding socket, Bracket, Connection cable, and Brightness-Sensor.

BREX Technology – Brake and Emergency Brake Light
BREX Technology provides different lighting indications for Normal operation, Braking, and Emergency braking, ensuring the best visibility for cyclists from behind. The integrated sensor is always active and reacts to braking or emergency braking situations, with no wiring to the brake required.

Normal Operation
The rear light with BREX Technology offers cyclists the best visibility from behind. The integrated sensor is always active and reacts as soon as it detects braking or emergency braking situations.

Braking
Upon detection of braking by the integrated sensor, the rear light shines very brightly and clearly to signal deceleration to following traffic participants. It is more than five times as bright as in normal operation, thus significantly brighter than previous brake rear lights with so-called “delay light”.

Emergency Braking
In the event of a sudden braking, the rear light activates the pulsating emergency brake light function. In this mode, BREX conveys the hazard situation with a signal effect never seen before, preventing accidents.

Instructions and Safety Information

The instruction manual is intended for users with knowledge and experience in assembling and mounting bicycle components. Specific tools are required. If you are not familiar with how bicycle components are assembled or mounted, or do not have the appropriate tools, please consult a bicycle specialist to carry out these works properly. Improper assembly of lighting components may lead to an accident with serious injuries.

Security Information

The manual uses signal words to draw attention to potential dangers or information. The meanings of these signal words are as follows:

WARNING

 Describes a hazardous situation which, if not avoided, could result in death or serious injury.

NOTE

 Refers to information that is important, but not hazard-related (e.g., information on property damage).

Information Symbol

 Points to other useful information about your new bicycle lighting.

Intended Use
Busch + Müller offers a diverse product portfolio of bicycle lighting. Not every lighting is suitable for every application and for driving on all surface types. There are restrictions. If you are not sure which type of lighting you need, you can either call our service hotline, send an email inquiry, or ask a bicycle dealer in your area for advice.

Legal Regulations
Before you ride your bicycle in public road traffic, you must familiarize yourself with the applicable laws and regulations of your country and the local provisions and always comply with them. In Germany, these can be found in the Road Traffic Regulations, and outside Germany in other sources, depending on your respective location.

Assembly Instructions
Depending on the desired mounting position (mudguard or saddle support/strut), align the sliding socket so that the rear light is later aligned at a 90-degree angle to the road surface (see sketch). When mounting on the fender, the rear light is attached with the included pan head screw. Please use only the original screw from Busch + Müller, as the rear light can be damaged if another screw is used. For saddle support/strut mounting, please use the enclosed cable ties.

Mounting Options
There are two mounting options provided: A for mudguard mounting and B for saddle support/strut mounting. It is important to ensure the rear light is oriented correctly towards the road.

Additional Notes and Liability

If the bicycle is sprayed with water, left upside down in the rain, or transported in the rain on a motor vehicle, the rear light should be covered so that no moisture can enter. Disposal: Rear lights with electronics are not part of household waste. They must be disposed of separately. Liability for damages resulting from improper handling, insufficient safe mounting, and the consequences thereof, such as immersion in water or other liquids, etc., is excluded from the warranty. Moreover, the warranty expires if the rear light is opened.

Warranty and Contact Information

We hope you enjoy your new rear light and always have a safe ride! For spare parts, please visit our spare parts shop: www.bumm-shop.de. Busch + Müller KG, 58540 Meinerzhagen, Germany, Tel. +49 2354 915-6000, Email: info@bumm.de, Website: www.bumm.de

Product Usage Instructions

Normal Operation
To use the product in normal operation mode, follow these steps:

Ensure that the product is properly installed and mounted.
Place the product on a suitable surface or road.
Turn on the product using the power switch.
Follow the instructions for operating the product as described in the user manual.

Braking
To brake while using the product, follow these steps:

Gradually apply pressure to the brake lever to slow down the product.
Release the brake lever to resume normal operation.

Emergency Braking
In case of an emergency, follow these steps to apply the emergency brake:

Immediately apply full pressure to the brake lever to stop theproduct as quickly as possible.
Release the brake lever only when the emergency situation has been resolved.

Fender Installation
To install the fender onto the product, follow these steps:

Refer to the provided instructions and diagrams for proper fender installation.
Attach the fender securely to the designated mounting points on the product.

Spare Parts
If you need to replace any parts of the product, you can find them in our online Spare Part Shop at www.bumm-shop.de.

Frequently Asked Questions (FAQ)

Q: Where can I find spare parts for the product?
A: You can find spare parts for the product in our online Spare Part Shop at www.bumm-shop.de.

How do I turn on the product?

To turn on the product, locate the power switch and toggle it to the On position.

How do I apply the emergency brake?

In case of an emergency, apply full pressure to the brake lever to activate the emergency brake. Release the brake lever only when the emergency situation has been resolved.

What is the Type No. of the Secuzed E Brex?

The Type No. is 333.

Can the Secuzed E Brex be used on all types of bicycles?

It is approved for bicycles with pedal assistance systems (E-Bikes) but not for vehicles requiring registration (quick E-Bikes).