ZALMAN CNPS10X Performa+ CPU Cooler User Manual
- June 4, 2024
- ZALMAN
Table of Contents
ZALMAN CNPS10X Performa+ CPU Cooler
Precautions
- This cooler must be used with a 120mm fan.
- Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries.
- Do not ingest the Thermal Grease, and avoid its contact with skin and eyes. If contact is made with skin, wash off with water. If ingested or irritation persists, seek medical attention.
- To prevent possible injuries, gloves must be worn while handling this product.
- Excessive force exerted on the fan may cause damage to the fan and/or system.
- Use and keep product away from reach of children.
- Check the components list and condition of the product before installation. If any problem is found, contact the retailer to obtain a replacement.
- During transportation of the system, the cooler must be removed. Zelman is not responsible for any damages that occur during the transport of a system.
- Product design and specifications may be revised to improve quality and performance.
Specifications
| Model | CNPS10X Performa+ |
|---|---|
| Dimensions | 131(L) X 96.5(W) X 151(H)mm |
| Weight | 713g |
| Material | Pure Copper and Aluminum |
| Heat Dissipation Area | 6,963cm² |
| Fan | Dimension |
| Speed | 900 – 2,000RPM ±10% |
| Noise Level | 17 – 36dBA ±10% |
| Bearing Type | Long Life Bearing |
| Control Method | PWM Control, Auto Restart |
| Connector | 4Pin |
| Input Voltage | 12V |
| Socket | Intel Socket LGA 2011/1366/1156/1155/1150/775 CPUs AMD Socket |
FM2/FM1/AM3+/AM3/AM2+/AM2 CPU & APUs
Thermal Grease| ZM-STG2M(ver2)
Components
Common Components
Intel Components
- Socket LGA 2011 V3/2011/1366/115X/775
- Stand off
AMD Components
- Socket FM2/FM1/AM3+/AM3/AM2+/AM2
Installation Requirements
-
Space Requirements
The cooler’s installation requires an unobstructed space of 96.5mm(width) 131mm(length) and 151mm(height) with the CPU as a central reference point. Please check if components such as ODDs and PSU protrude into the required space. -
Air Guide Removal
Air guides on enclosures must be removed before the cooler’s installation since they protrude into the cooler’s required space.
-
Cooler Orientation
As shown in the diagram below, it is recommended that the cooler be installed so that air flows from the cooler toward the enclosure’s rear exhaust fan to be released. -
Recommended cooler orientation may differ according to the motherboard model.
-
CPU and RAM interference check
Any RAM with a height taller than 36mm (1.42) will have interference with the CPU cooler. Please check the height of your RAM modules prior to installation.
Installation
LGA Intel Socket Installation
-
Intel Socket 2011 V3 / 2011 User
Partially unscrew the four bolts located on the base of the CPU cooler. Then insert the Intel Clips between the base and the hepatize cover, with the clips bent away from the heatsink.
-
Intel Socket 1366 / 115X / 775 User
Partially unscrew the four bolts located on the base of the CPU cooler. Then, insert the Intel Clips between the base and the hepatize cover, with the clips bent away from the heatsink.
Install the Bolts to the Backplate according to the socket type and secure them with Side Caps.
-
Backplate is not needed for LGA 2011 V3 / 2011 sockets.
Caution
Take note of the orientation of the Nuts and the Side Caps.
-
Socket 1366/115X Installation
Peel off one side of the Double-sided Tape and attach it to the center of the Backplate with the sticky side facing down. Then, peel off the top cover.- Socket 1366/115X Installation does not require the Loading Block.
- Socket 1366/115X Installation does not require the Loading Block.
-
Socket 775 Installation
Peel off the Loading Block cover and attach it to the Backplate with the sticky side facing the center of the Backplate.
Peel off one side of the Double-sided Tape and attach it with the sticky side
facing the Loading block. Then, peel off the top cover.
Caution
Please make note of the orientation of the Loading Block’s Installation.
Socket 1366 / 115X / 775 User
Attach the Backplate assembly to the back side of the motherboard by aligning
the Nuts to the motherboard mounting holes. If you were unsuccessful at first
attempt, you may continue with the installation without the Double-sided Tape
as it is not a necessary component.
Socket 2011 V3 / 2011 User
Fasten the four Stand-offs to the motherboard. Backplate is not needed.
Apply thermal grease just enough to thinly cover the CPU surface, then fasten
the Bolts to install the cooler.
Latch the Fan Fixing Clips to the notches located on the sides of the
heatsink. Note: It is often easier to latch the Fan Fixing Clips one at a time
.
Position the fan as low as possible.
Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan header.
Caution
Please make sure that PWM Control Mode is activated in the motherboard’s BIOS
settings.
AMD Socket Installation
Partially unscrew the four bolts located on the base of the CPU cooler. Then,
insert the AMD Clips between the base and the hepatize cover, with the clips
bent away from the heatsink.
Install Bolts to the Backplate according to the Socket Type and secure with
Side Caps.
Caution
Take note of the orientation of the Nuts and the Side Caps.
Peel off the Loading Block cover and attach it to the Backplate with the
sticky side facing the center of the Backplate.
Peel off one side of the Double-sided Tape and attach it with the sticky side
facing the Loading block. Then, peel off the top cover.
Caution
Please make note of the orientation of the Loading Block’s Installation.
Dismantle the CPU cooler retention bracket on the motherboard by unscrewing
the four bolts located at each corner (method may vary; consult the
motherboard manual for details). Be sure to keep the retention bracket so the
stock CPU cooler can be used as a backup.
Attach the Backplate assembly to the back side of the motherboard by aligning
the Nuts to the motherboard mounting holes. If you were unsuccessful at first
attempt, you may continue
with the installation without the Double-sided Tape as it is not a necessary
component.
Apply thermal grease just enough to thinly cover the CPU
surface, then fasten the Bolts to install the cooler.
Latch the Fan Fixing Clips to the notches located on the sides of the
heatsink. Note: It is often easier to latch the Fan Fixing Clips one at a
time.
Position the fan as low as possible.
Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan header.
Caution
Please make sure that PWM Control Mode is activated in the motherboard’s BIOS
settings.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>