Dynojet Yamaha R1 QuickShifter Expansion Module Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-22037
Model Coverage: 2004-2006 Yamaha R1
Installation Guide
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two
base maps when you hook up a switch to the MAP inputs. You can use any
open/close type switch. The polarity of
the wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2
by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this
input. This will allow you to calculate gear position in the Control Center
Software. Once gear position is setup
you can alter your map based on gear position and setup gear-dependent kill
times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged
(continuity) will only allow the RPM to be raised to a certain limit (set in
the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat.
-
Prop the front of the fuel tank in the up position.
-
Lay the PC6 in the tail section.
-
Route the harness underneath the tail section and go towards the front of the bike.
-
Locate the connector from the main wiring harness to the injector rail.
-
Unplug this connector as shown.
This connector is GREY in color.
-
Attach the connectors from the PC6 to the stock wiring harness as shown.
-
Bolt the fuel tank down into position.
-
Remove the two bolts on the left-hand side of the battery hold-down bracket and loosen the right-hand bolts enough to route the PC6 harness underneath it as shown.
-
Reinstall the bracket.
-
Attach the ground wire from the PC6 to the negative side of the battery as shown.
-
Using the supplied Velcro, secure the PC6 in the rear section of the trunk as shown.
Make sure to clean both surfaces with the alcohol swab before attaching. -
Verify all the wires are routed properly.
-
Reinstall the main seat and the passenger seat.
Download the latest map files from our website at dynojet.com/tunes.
Optional inputs:
Temperature input – GREEN/WHITE wire – pin #31 of ECU.
12v source for Autotune – BLUE wire of tail light connector which is
behind the left-hand side panel.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2004-2022 DYNOJET RESEARCH
ALL RIGHTS RESERVED
IPC6-22037.01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>