vicseed ZJ4A Holder Phone Mount Magnetic Car Instruction Manual
- June 16, 2024
- vicseed
Table of Contents
HOLDER
MAGNETIC CAR
PHONE MOUNT
MAKE YOUR LIFE SIMPLE
VDPI01005A
Specifications
| Product Name | Magnetic Car Phone Mount |
|---|---|
| Model | ZJ4A |
| Package List | Magnetic Car Phone Mount ×1, |
Accessories Package ×1,
User Guide ×1
The parameters above are derived from the laboratory of VICSEED. The actual parameters may differ from product to product or other factors. All images shown here are for reference only.
Overview
Accessories Package
Operating Instructions
The magnetic car phone mount shall be used in the following 3 usage conditions, please choose the corresponding usage according to your mobile phone.
- iPhone 12/13/14/15 series phones or newer: Use Without Metal Ring
- Phone 12/13/14/15 series phones or newer with MagSafe Cases or magnetic cases: Use Without Metal Ring
- Other situations: Please Use with the Metal Ring
Note: The metal ring must stick outside of the phone case
a. iPhone 12/13/14/15 series phonesor newer with Non-magnetic cases
Assembling the Metal Ring
Note:
- To better protect your phone, it is recommended that you paste the metal ring on the back of the phone case.
- There are two ways to paste the metal ring, which are listed as follows. Please choose between them according to your needs.
If you use a bare phone or a smooth flat phone case, please use the
transparent sticker before sticking the metal ring
If you use a phone case with textured or matte surface, please use the metal
ring directly
- Before pasting the metal ring, please be sure to use phone match-up card to align the pasting position, avoid misalignment and affect the wireless charging function of your phone.
Paste steps:
-
Use a cleaning wipe to clean the back of the phone (or phone case) where the metal ring needs to be pasted.
If use a phone case, please install the metal ring OUTSIDE of your phone case. -
Unfold the match-up card.
Scale| Phone Models
---|---
5.4 in| iPhone mini/iPhone SE series models
6.1 in| iPhone11/11 Pro/12/12 Pro/13/13
Pro/14/15 and other models
6.7 in| iPhone Plus/iPhone Pro Max series
models -
Align the circle of the match-up card to the center of the phone. Make sure the edge of the circle is the same length to the top and bottom/ left and right of the phone. (You can paste the transparent sticker to fix the match-up card according to your needs.)
-
Tear off the protective paper of the transparent sticker and paste the transparent sticker onto the center of your phone/phone case.
Note: Please don’t use the transparent sticker if your phone case is textured or matte. -
Tear off the protective paper of the metal ring and paste the metal ring onto the center of your phone/phone case.
-
Press firmly along the metal ring to secure it.
-
Important Note: After applying the metal ring, please wait for 24 hours.
-
Remove the match-up card, and the installation is completed.
Assembling the Car Mount
- Please insert the car mount into a suitable place on the air vent, and adjust the angle of the magnetic organizer to fit your view.
- Put the phone on the magnetic car phone mount and use it.
Attentions
A.Please insert the vent clip by swaying it from side to side. By this way,
you will feel easier to install it . B.Please use the provided supporting pad
if you meet the below situations a. If the air vent gaps are wider, the
product may only attach to a single vent (as shown in Figure ①) b. the vent
blades are moving around(as shown in Figure ②)
To address this, please attach the provided supporting pad
over the vent clip before inserting the phone holder into the vent. This will
ensure a more stable installation by securing the car mount.
Note: Please attach the outmost edge of the supporting pad to the outmost
edge of the air vent if it is the situation b
C. In case the phone holder falls off, please use the spare silicone piece.
Peel off the protective film, attach the silicone piece to the air vent blade,
then insert the car mount’s clip into the spot where the silicone piece is
attached. This silicone piece increases friction, preventing the car mount
from shaking or sliding.
Warning
- Avoid dropping.
- Do not disassemble.
- Do not install while driving.
- Do not install the car mount in places which interferes with air bag or driving.
- Please keep this product away from any magnetic items, otherwise, demagnetization might happen.
- Keep the car mount away from children.
Customer Service
12-month limited warranty
Lifetime technical support
SHENZHEN HOMGMI TECHNOLOGY CO., LTD.
Add : RM1503, BLK C, Zhantao Technology BLDG, Minzhi Avenue,
Minzhi ST, Longhua DIST, Shenzhen, China
Email : support@vicseed.com
Web : www.vicseed.com
Shenzhen Homgmi Technology Co., Ltd. All Rights Reserved.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>