HAVIT Highlite Bollard Light Instruction Manual

: June 4, 2024
: havit

Table of Contents

HAVIT Highlite Bollard Light
Product Specifications
Mounting Base
Dimensions
Important Safety Issues
Steps for Installation
Must be installed by a licensed electrician
Highlite Bollard Light Installation Instructions
Important Safety Issues
Steps for Installation
Must be installed by a licensed electrician
Documents / Resources

HAVIT Highlite Bollard Light

Product Specifications

Mounting Base

Dimensions

Important Safety Issues

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
When installing surface mounted bollards, base plate must be installed on concrete or concrete pad, Fitting should not be installed under ground level, all holes including cable entry must be silliconed to prevent any water pentration into fitting, silicon must also be appiled around fitting at ground level. Failure to do this will void warranty
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation

Make sure that the electrical circuit is free of voltage (master switch off).
Remove baseplate from fitting by twisting anti clockwise.
Install baseplate in desired location using apropriate screws for application. The screws supplied are mild steel which must be replaced with higher grade if there is any chance of them being affected by water. The location of baseplate must be installed on either concrete or concrete base and cannot be installed under ground level.
If using extension piece, attach it to Bollard now by twisting clockwise until 2 pieces are completely together.
Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
Strip back cable on both fittings and cable run and twist the positive cable from fitting to positive on the cable run, then connect neutral from fitting to neutral on the cable run.
Solder all joins using solder and either a heat gun or butane gas torch.
Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
Heat the heat shrink or crimp the gel cap making sure all connections are covered.
Silicon all cable entry holes and fixing points on baseplate to avoid moisture penetration into fitting.
Affix the bollard to the baseplate by twisting clockwise until it stops.
Colour temperature is set to 3000K. To change, remove cap from fitting by twisting anti clockwise. Select desired colour temperature by moving switch located on the centre of PCB
Attach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician

Contact Details
143 Beauchamp Road Matraville NSW 2036 Australia

Tel : 02 9381 8300
Fax : 02 9666 8881
Email : sales@havit.com.au
Web : www.havit.com.au

Warranty Terms & Conditions

Additional Information

Highlite Bollard Light Installation Instructions

Product Specifications

Mounting Base

Dimensions

Important Safety Issues

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
When installing surface mounted bollards, base plate must be installed on concrete or concrete pad, Fitting should not be installed under ground level, all holes including cable entry must be silliconed to prevent any water pentration into fitting, silicon must also be appiled around fitting at ground level. Failure to do this will void warranty
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation

Make sure that the electrical circuit is free of voltage (master switch off).
Remove baseplate from fitting by twisting anti clockwise.
Install baseplate in desired location using apropriate screws for application. The screws supplied are mild steel which must be replaced with higher grade if there is any chance of them being affected by water. The location of baseplate must be installed on either concrete or concrete base and cannot be installed under ground level.
If using extension piece, attach it to Bollard now by twisting clockwise until 2 pieces are completely together.
Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
Strip back cable on both fittings and cable run and twist the positive cable from fitting to positive on the cable run, then connect neutral from fitting to neutral on the cable run.
Solder all joins using solder and either a heat gun or butane gas torch.
Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
Heat the heat shrink or crimp the gel cap making sure all connections are covered.
Silicon all cable entry holes and fixing points on baseplate to avoid moisture penetration into fitting.
Affix the bollard to the baseplate by twisting clockwise until it stops.
Colour temperature is set to 3000K. To change, remove cap from fitting by twisting anti clockwise. Select desired colour temperature by moving switch located on the centre of PCB
Attach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.