tp-link Tapo S200D Dimmer Switch User Guide
- June 5, 2024
- tp-link
Table of Contents
tp-link Tapo S200D Dimmer Switch
Quick Start Guide
Meet Your Smart Dimmer Switch
- Control lights, appliances, and other connected devices at the touch of a dimmer switch. Smart Dimmer Switch can also be an instant trigger for Tapo Hub.
Before You Start
- A Tapo Hub is required. Make sure your Tapo Hub is successfully added via the Tapo app.
Power Up Your Button
- Hold the main body by the small tabs to prevent free rotation. Then twist the lid anticlockwise and remove the lid.
- Remove the battery insulation tab to power up your button.
Set Up Your Dimmer Switch
- Open the Tapo app, tap the button in the app, and select your model. Follow app instructions to complete the setup.
Test Your Dimmer Switch
- Press the button to test it. Make sure the Tapo app shows the button is tapped when you press it.
Mount Your Dimmer Switch
- Once you’ve decided on a location, secure the wallplate with either the included screws or the attached tape. Attach the button to the faceplate, and the button will be magnetically attracted.
OR
Do not ingest the battery, Chemical Burn Hazard This product contains a
coin/button cell battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away from
children. If you think batteries might have been swallowed or placed inside
any part of the body, seek immediate medical attention.
Safety Information
Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.Do not use the device where wireless devices are not allowed. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type Avoid replacement of a battery with an incorrect type that can defeat a safeguard. Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, which can result in an explosion. Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; Do not leave a battery subjected to the extremely low air pressure that may result in an explosion or leakage of flammable liquid or gas.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provided with antenna
installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>