Foxeer VTX Reaper Extreme User Manual

June 16, 2024
FOXEER

Foxeer-LOGO

Foxeer VTX Reaper Extreme

Reaper Extreme VTX

Specifications

  • Size: 3627.58mm
  • Connector: MMCX
  • Display: 3LED
  • Weight: 13g
  • Power: 25mW/200mW/500mW/1.5W/2.5W
  • Input: 9~36V
  • Output: 5V
  • Channel: 40CH
  • Protocol: Tramp

Product Usage Instructions

LED Description

  • LED Colors: Red, Green, Blue
  • Description: The LED lights on the VTX indicate the power level and channel/band selection.

Button Operation

  • Channel select mode: Short click the button to enter the CHANNEL setup. Only the green light will be on and flash. Select the desired channel by short presses.
  • Band select mode: Continue to press the button for 3 seconds to enter the BAND setup. The blue LED will be on and flash. Select the desired band by short clicking the button.
  • Power select mode: Continue to press the button for 3 seconds to enter the POWER setup. The red LED will be on and flash. Select the desired power level by simple short presses.

Frequency Table

Channel CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
Band A 5865 5845 5825 5805 5785 5765 5745 5725
Band B 5733 5752 5771 5790 5809 5828 5847 5866
Band E 5705 5685 5665 5645 5885 5905 5925 5945
Band F 5740 5760 5780 5800 5820 5840 5860 5880
Race Band 5658 5695 5732 5769 5806 5843 5880 5917
PIT 25 200 500 1.5W 2.5W

Note : Black parts are locked by default.

Unlock the frequencies and power levels
To unlock all frequencies and power levels, long press the KEY button until the red LED (PWR) is constantly on, then off, and then on again. Release the button. A flashed red LED indicates an unlocked status, while a constant red LED indicates a locked status.

PIT Mode On/Off:
To turn on/off the PIT Mode, double-click the KEY button. When the red LED (PWR) is off, it means PIT mode is on. When the red LED (PWR) is on, it means PIT mode is off. In PIT mode, the VTX output is extremely low power.

Notes

  • If the tramp cable is connected, the button will not work, and you cannot adjust the frequency and power. The controller will take over.

FAQ

  1. How to select a channel?
    Short click the button to enter CHANNEL setup mode. Use short presses to cycle through the available channels until you reach the desired one.

  2. How to select a band?
    Continue to press the button for 3 seconds to enter BAND setup mode. Use short clicks to cycle through the available bands until you reach the desired one.

  3. How to select a power level?
    Continue to press the button for 3 seconds to enter POWER setup mode. Use simple short presses to cycle through the available power levels until you reach the desired one.

  4. How to unlock the frequencies and power levels?
    Long press the KEY button until the red LED (PWR) is constantly on, then off, and then on again. Release the button to unlock all frequencies and power levels.

  5. How to turn on/off PIT Mode?
    Double-click the KEY button to turn on/off PIT Mode. When the red LED (PWR) is off, it means PIT mode is on. When the red LED (PWR) is on, it means PIT mode is off.

Spec

  1. Size: 3627.58mm
  2. Connector: MMCX
  3. Display: 3LED
  4. Weight: 13g
  5. Power: 25mW/200mW/500mW/1.5W/2.5W
  6. Input: 9~36V
  7. Output: 5V
  8. Channel: 40CH
  9. Protocol: Tramp

LED

Button Operation

  • Channel select mode:
    Short click, enter CHANNEL setup, only green light is on and flash, select channel by short presses.

  • Band select mode:
    Continue topress the button for 3s, enter BAND setup, blue LED on and flash, select band by short click.

  • Power select mode:
    Continue to press the button for 3s, enter POWER setup, RED LED is on and flash, select power by simple short presses.

Frequency Table

Foxeer-VTX-Reaper-Extreme- \(2\)

  • Black parts are locked by default.

Unlock the frequencies and power levels
Long press the “KEY” button until the Red LED (PWR) is constant on, off, then on again, release the button unlock the all frequencies and power levels, flashed Red LED means in unlocked status, constant Red LED means in locked status.

PIT Mode On/Off
Double-click the “KEY” button to turn on/off the PIT Mode. Red LED (PWR) off means PIT mode on; Red LED (PWR) on means PIT mode off。In PIT mode, VTx output extreme low power.

Notes
If tramp cable is connected, button will not work, can not adjust frequency and power, controller will take over.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals