SHARP PJ-IGS16SG(WH) Plasmacluster Ion Electric Stand Fan User Manual
- June 10, 2024
- Sharp
Table of Contents
SHARP PJ-IGS16SG(WH) Plasmacluster Ion Electric Stand Fan
The numbers on this technology mark indicates that the product is placed near the wall operating at its “maximum air volume”. Measured from the center of the room (1.2m above the floor) with a common floor area.
Plasmacluster Ion logo and Plasmacl uster Ion are registered trademarks of Sharp Corporation in Japan, Philippines, and elsewhere.
Dear Customer,
Thank you very much for purchasing the Sharp Brand.
Please read this manual carefully before operating this product. Keep this
manual handy for further references.
FEATURES
What is “Plasmacluster Ion” Technology?
The same plasma and negative ions as those present in nature are created and
emitted by plasma discharge.
This is an original technology of Sharp that suppresses the actions of viruses
and fungi suspended in air.
The ions are of the same type as the ions present in nature, and the mechanism
of their actions has been understood and their safety has been verified.
A “Geee” sound is generated when plasmacluster ions are generated, and is not
abnormal. Depending on the operating environment and operation mode, the
intervals between sounds may change or the sounds may be loud.
MAINTENANCE
- If dust is attached to the electrode part of the unit remove it with a cleaning brush.
- To clean the blades and the main unit, wipe them off with a cloth dampened with warm water or a neutral detergent, and then wipe them with a soft cloth.
- Dust or water may adhere between the plug and the outlet, so remove the plug and wipe it with a dry cloth before using.
PARTS IDENTIFICATION
-
Sharp PCI Decal
-
Front Grill I 3
-
Blade Nut
-
Blade
-
Grill Nut
-
Back Grill
-
Front Motor Cover
-
PCI Module 0
-
Oscillation Knob ®
-
Rear Motor Cover
-
Speed Indicator Sticker
-
Switch Box Assembly with Knob
-
T-Screw
-
AC Cord
-
Stand Pipe Assembly
-
Plain Base Top
-
Base Bottom
(Counterweight) -
L-Screw with washer
CAUTION!
- This product is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Unless they have been given supervision or instructions.
- Children must be supervised not to play with this product.
WARNING: If unusual oscillating movement is observed, Immediately stop using the Electric Fan and contact the manufacturer, its service agent, or suitably qualified person.
SAFETY PRECAUTIONS
- For safety, switch off unit and unplug from AC mains before cleaning or removing fan.
- Use this fan with specified voltage as stated on the rating sticker. Make sure the voltage specified corresponds to the AC supply at your house before connecting to main AC.
- Do not insert finger or other objects into fan when operating.
- Do not attempt to repair the fan. Always refer to authorized service centers for repairs.
- Do not immerse the fan in water or other liquids.
- Do not use outdoors or near windows.Rain drops may cause electrical hazards.
- If the power cord is damaged, it must be replaced by an authorized service agent or the manufacturer to avoid any hazards.
- Do not use the following as cleaning solvents: petrol, thinner or benzene.
- Use mild soap with damp cloth or sponge to clean plastic parts.
ASSEMBLY METHODR
-
Unpack contents from carton box.
-
Fix the stand pipe assembly into plastic base assembly and tighten by L-screw.
-
Fix the stand pipe assembly into the switch box assembly in correct direction. Ensure the T-screw is properly tightened.
-
Fix the back grill to the motor assembly by matching holes of back grill to the two (2) round pins on the front of the motor assembly.
-
Fasten the fixing nut by turning in clockwise direction.
-
Insert the fan blade and the blade nut to the motor shaft.
-
Lock the fan blade by turning the blade nut in counterclockwise direction.
-
Hold the front grill with logo in an upright position and attach to the back grill. Secure it using the snap type ring clip.
-
Ensure the ring clip is properly snapped.
It’s now ready to use.
SPECIFICATION
Model No.: PJ-IGS16SG(WH)
Blade size| Voltage| Power| Speed (RPM)| No. of Running Position| Class of
Insulation| Ion Concentration
---|---|---|---|---|---|---
Low| High
16″
(40cm)
| 220-240V-
50/60 Hz
| 50W| 950 RPM| **** 1300 RPM| 3| Class B| 7000 ion s/cm ‘
OPERATING INSTRUCTIONS
-
Plug in the fan to 220 – 240V AC, 50/60 Hz power supply.
-
ON-OFF SETTING
A. To turn on the unit, select and push numbers 1,2 or 3 depending on your desired speed. The LED indicator light will light up. Plasmacluster Ions are generated in all operating speed.
B. Push “OFF” to turn the unit off. -
OSCILLATION
The fan will oscillate during operation when the oscillation knob is in the down position.
When the oscillation knob is in the up position, the fan does not oscillate. -
NECK POSITIONING
To adjust vertical angle, switch off the appliance and lilt angle up or down as needed.
ASSEMBLY METHOD
(FROM STAND FAN TO TABLE FAN)
-
Fix the washer in the adaptor using 3x12mm screw. Place the nut in the adaptor as shown in the drawing.
-
Fix the adaptor in the plastic base assembly with counterweight and tighten using the L-Screw with washer .
-
Place the switchbox assembly on the adaptor.
-
Tighten the assembly using the T- Screw
-
Finished Unit
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>