GENYED TWNO38 Safety Glasses with Interchangeable Lenses User Manual

GENYED TWNO38 Safety Glasses with Interchangeable Lenses

Description And Product Overview

1. Safety glasses model GENYED® TWN038 with polycarbonate lenses and frame made of polycarbonate and rubber. Supplied with clear lenses and dark replacement lenses, suitable for both outdoor and indoor use.
2. Quick and easy lens replacement.
3. The product meets the European CE standard EN 166:2001 and complies with PPE Regulation (EU) 2016/425, CE and UKCA marked.
4. Clear and dark lenses with anti-scratch and anti-fog treatment.
5. Clear and dark lenses with UV400 protection.
6. Suitable for protection against low impact shocks typical of factories, laboratories, educational establishments, DIY activities, etc., which could damage the eyes or impair vision.

Safety Precautions

1. Read the user manual carefully before using the product.
2. Do not modify or alter the product under any circumstances.
3. Do not use this product to protect yourself against risks other than those specified in this document/instruction manual.
4. GENYED® TWN038 safety glasses must be replaced after two years of use.

Specifications

1. Frame marking: G EN166 F CE UKCA – Lot number
2. Lens marking: 2C-1.2 G 1F CE (clear) / 5-2.5 G 1F CE (dark)
3. Dark lenses: category 2 – transmittance 24% +/- 3%
4. Impact resistance: F (low impact 45M/S)
5. Optical class: 1
6. Frame colour: blue/grey; Lens colour: n.1 clear – n.1 dark/smoke
7. Weight: 1.02oz

Use

1. Check carefully before putting on the glasses that the lenses are perfectly clean, have no scratches and are fitted correctly.
2. Wear the glasses before exposing yourself to any hazardous conditions for which protection is required.
3. PPE is intended for personal protection and must not be interchanged between multiple users.
4. Ensure that the protective eyewear is worn comfortably.
5. Wear the goggles for the entire duration of exposure to the risks.
6. If the glasses have scratches, damage or have been subjected to shocks, replace them immediately.

Replacing Lenses (See Image A)

Declaration of conformity and complete documentation: https://www.genyed.com/doc/safety-glasses/sg-4262.html

Clear lenses can be exchanged for dark ones and vice versa.

Dismantling : close the temples (1) – slide the grey part (the part between the lens and the temples) in the direction of the temples by approx. 0.08in (2) – pull the lens down from the side of the temples to remove it (3).

Fitting : insert the lens from the middle of the nose piece (4) – push up the outer part of the lens until the lens is in the correct position (5) – slide the grey part towards the lens to lock it (6).

IMPORTANT : Make sure that the lenses are fully locked in place before putting the glasses on.

Cleaning

1. Cleaning should only be carried out using a special lens cloth.
2. The standard anti-fog treatment gradually fades and may peel off after washing. Therefore, only use lens-specific cloths.
3. Do not clean any part of the product with petrol, chlorinated degreasers, organic solvents or abrasive cleaning agents.

Storage Instructions

1. Store the glasses and lenses in a protected, dry, cool and well-ventilated place away from sunlight and away from chemical and abrasive substances.
2. Store between 5 to 40℃; humidity less than 90%.

Warranty [2 years]

1. The product warranty is 2 years.
2. Damage resulting from improper use is not covered

PPE Conformity Assessment Body

Notified body:

CERTOTTICA S.c.r.l. (0530)
Zona Industriale Villanova
32013 Longarone (BL), Italy

Packaging materials : bag > plastic; sticker > paper; instructions > paper.

Customer Support

GENYED Srls Via Maino, 6 – 21013 Gallarate Italy www.genyed.com – info@genyed.com

References

• GENYED® - Home Page
• Documentation

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>