BWT Barrier iMaster Complex Water Filter Equipment User Manual

BWT Barrier iMaster Complex Water Filter Equipment User Manual

Intended purpose of water filter

«BARRIER iMaster» domestic water filtration system is intended for post- treatment of drinking tap water to remove mechanical impurities, active chlorine, organic contaminants, heavy metals and other contaminants. The multi-stage system ensures highly effective purification throughout the service life of the replaceable filter elements. «BARRIER iMaster » water filter is easy to install under the sink. It is completed with everything needed for you to install it. The set includes an elegant filtered water spigot. «BARRIER iMaster » can operate twenty-four hours a day.

Attention!
BARRIER iMaster is intended for post-treatment of tap water only from centralized water utilities. It is prohibited to use the water filter to treat water that poses microbiological risks.

Filtration System Packages

Attention!
When the time comes to replace the filter elements, use only those indicated in this manual. Failure to follow this requirement may lead to a change in the functional capacities and technical characteristics of the water filter.

Technical Specifications

• The service life may vary from that shown depending on the level of inlet water contamination. The service life of the softening cartridge is shown on page 23 of this manual.

Delivery Set

Water Filter Connection Diagram

BARRIER iMaster System Installation

Before installation please read the instructions carefully and study the filtration system connection diagram. Check that all the required parts are present in the set. First, decide where you are going to hang the filtration system under the sink, as well as where you plan to install the filtered water spigot to ensure maximum convenience in daily use. The filtration system should be hung on the wall using the screws leaving at least 1 cm of clearance below the assembled system. Ensure that the filtration system and the connecting plastic tubes do not come into contact with hot water pipes.

Filtration System Installation Process

Attention!
Before beginning the installation of the water filter close the ball valve at the cold water main inlet, and then open cold water cock of the mixing faucet, to bleed pressure out of the pipe.

Start of work with BARRIER iMaster

Before using «BARRIER iMaster»:

1. Check that the filtration system is properly connected in accordance with the diagram on page 18 of this Manual.
2. Ensure that the ball valve is shut off.
3. Turn on the filtered water spigot.
4. Open the valve to the cold water main.
5. Open the ball valve. For a few minutes the filtration system will fill with water before it comes out of the filtered water spigot. *
6. Using the ball valve, set the optimum water flow in accordance with the technical characteristics of the filtration system. *
7. Turn off the filtered water spigot.
8. Ensure there are no leaks. If needed, tighten the connections and make sure that the plastic tubes are properly installed in the fittings.
9. Turn on the filtered water spigot and flush 10 1 of water through the system to rinse the filter elements.
   ” The first few litres of filtered water may have a dark or cloudy appearance. It means that charcoal dust or air bubbles are being rinsed out ottne filter elements. The water filter operates correctly.
   ” During the service life of the filter elements, the flow rate of the filter may decrease. Restore optimum water now by adjusting the ball valve_

Filter Element Replacement

The Water Filter Set includes filter elements made of the most effective materials and components. Nevertheless the service life of the filter elements is limited and for the system to continue purifying the water at the same level of efficiency, the elements must be replaced in due time.

Attention!
Filter elements should be replaced regularly, at least once a year.
In case, when the water with high levels of mechanical impurities enters the water filter, the first-stage filter element should be changed if the flow rate of filtered water falls below optimum levels.

The recommended replacement frequency for the «BARRIER iMaster» Softening filter element depends on the pre-filtration water hardness.

Recommendations

• Use «BARRIER iMaster» only for intended purpose.
• Keep the water purifier clean and protect it from shock and other mechanical damage.
• Prevent excessive strain or bending ofthe plastic tubing.
• Do not allow the water filte or plastic tubing to come into contact with hot water pipes.
• Do not allow the water in th filter and filter elements to freeze.
• When leaving the water filter unused for extended periods (over 2 days), we recommend shutting off the ball valve a the inlet to the water filter. Before using again, flush the system with at least 10 litrers of water.

Manufacturer’s Warranty

The manufacturer guarantees the correct operation of the water purifier for a period of 12 months from the date of sale. The service life of the elbow attachment is 5 years. The buyer is entitled to lay claims to the manufacturer (seller) in accordance with Article 18 of the RF Law ‘On Protecting Consumer Rights’ in the event that flaws are discovered within the warranty period. The Manufacturer is exempt from responsibility in the cases provided for in Article 18, Paragraph 2, Clause 6 of the RF Law ‘On Protecting Consumer Rights’

Attention!
A pressure reducing valve must be obligatory installed, if the inlet pressure would be in excess of the maximum rated level, specified by the manufacturer.

Failure to do so voids the warranty.

Store at temperature from -25 to +40 oc.

The manufacturer retains the right to introduce changes to the design of the water filter that do not worsen its performance.

The quality management system at BWT BARRIER RUS is certified as complying with
ISO 9001.

Read More About This Manual & Download PDF:

References

• Trang chủ - Máy lọc nước bwt barrier imaster

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>