BWT BC50 Rechargeable Pool and Spa Vacuum User Manual

BWT BC50 Rechargeable Pool and Spa Vacuum

Product Information

The BC Line BC50 is a pool vacuum designed for efficient cleaning and maintenance of swimming pools. It is equipped with a rechargeable Li-ion battery pack and comes with a detachable supply unit (external adaptor) for charging. The pool vacuum has a maximum operating depth of 3 meters (9.8ft).

Product Usage Instructions

• Safety Warnings:
  • This pool vacuum is not a toy and should be kept out of reach of children.
  • Children should not operate the pool vacuum.
  • This appliance is not intended for use by individuals with reduced physical, sensory, or mental capabilities, unless they are supervised or instructed on its safe use.
  • Children must not play with the product or carry out its cleaning and maintenance.
• Pool Vacuum Operation:
  • Ensure the pool vacuum is fully immersed in the pool before starting operation.
  • The minimum water level required for operation should reach above the power ON/OFF switch of the pool vacuum when held vertically.
  • Operating the pool vacuum when not immersed correctly may damage the unit and void the warranty.
  • Do not operate the pool vacuum when people or pets are present in the water.
• Charging and Maintenance:
  • Only recharge the pool vacuum using the provided external adaptor and charging base.
  • Use the detachable supply unit (external adaptor) with the specified model number to charge the battery.
  • Connect the external adaptor to a power source through a residential current device (RCD) or a ground fault circuit interrupter (GFCI).
  • Do not handle the pool vacuum, external adaptor, and charging base with wet limbs and without shoes while charging.
  • Disconnect the external adaptor from the power source and unplug it from the charging base before detaching the pool vacuum.
  • Clean the filter and charging contact plates regularly.
• General Safety:
  • Do not use the pool vacuum if any damage is detected.
  • Replace damaged parts with certified ones from the distributor or manufacturer.
  • Avoid handling the external adaptor and charging base when wet.
  • Do not attempt to open the external adaptor and charging base.
  • Keep the external adaptor disconnected from power when not in use.
  • Do not use the pool vacuum without an intact filter cone, as it may void the warranty.
  • Be aware of suction entrapment hazards as the pool vacuum generates suction.

SAFETY WARNINGS & INSTRUCTIONS

Information contained in this Instruction Manual will help you operate the item safely, protect yourself and others from hazards, and prevent damage to the device and other property.
SAVE THESE INSTRUCTIONS

WARNING!

• This is not a TOY. Children should be kept out of reach from this pool vacuum and its accessories.
• Never allow children to operate this pool vacuum.
• This appliance is not intended for use by persons with reduced physical, sensory, mental capabilities, or a lack of experience and knowledge, unless they are given supervision or instructions concerning the safe use of the appliance and understand the hazards involved by a person responsible for their safety.
• Children must not play with this product.
• Cleaning and maintenance of the pool vacuum must not be carried out by children.
• Make sure the pool vacuum is fully immersed in the pool before initiating operation. The minimum water level required to operate the pool vacuum must reach above the power ON/OFF switch of the pool vacuum when it is held in a vertical position. Operating the pool vacuum when it is not immersed correctly could damage the unit and void the warranty.
• Maximum operating depth in water is 3 meters (9.8ft).
• Maximum water temperature: 5˚C (41˚F) –35˚C (95˚F)
• Detachable supply unit (external adaptor).
• The pool vacuum should only be recharged with the external adaptor and charging base delivered with this product.
• For the purposes of recharging the battery, only use the detachable supply unit (external adaptor model number: DSS12D-1261000-B /DSS12D-1261000-C / DSS12D-1261000-D/ LX135100U) that provided with this pool vacuum to charge the battery.
• Connect the external adaptor to a power source through a residential current device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt, consult a qualified electrician.
• Do NOT use this pool vacuum if any damage is detected.
• Replace damaged parts with ones that are certified by the distributor or manufacturer.
• Turn off the power, disconnect the external adaptor from the power source, and unplug the external adaptor from the charging base before detaching the pool vacuum from the charging base.
• Disconnect the pool vacuum from the supply mains and make sure the pool vacuum is OFF prior to carrying out regular maintenance – such as cleaning the filter and the charging contact plates.
• DO NOT attempt to replace the installed rechargeable Li-ion battery pack.
• DO NOT handle the pool vacuum, external adaptor, and charging base while it is charging with wet limbs and without shoes.
• You should not operate this pool vacuum when people/pets are present in the water.
• DO NOT use this pool vacuum without an intact filter cone in place, as your warranty will be voided as a result.
• Suction entrapment hazard: This pool vacuum generates suction. Do not allow hair, body, or any loose parts of your clothing to make contact with the suction hole of the pool vacuum during its operation.
• Never insert body parts, clothing or other objects into the openings and moving parts of the pool vacuum.
• DO NOT use this pool vacuum to pick up any toxic substance, flammable, and combustible liquids (i.e. gasoline) in the presence of explosive or flammable fumes.
• Under no circumstances should you attempt to disassemble the pool vacuum and replace the impeller, motor, and battery by yourself.
• Never insert fingers or any object to touch the impeller.
• The built-in battery must be removed by a skilled technician before it is scrapped.
• This pool vacumm contains a battery that are only to be removed by skilled persons.
• The pool vacumm must be disconnected from the supply mains as the battery is removed.
• For details regarding battery recycling/disposal, refer to the section “BATTERY DISPOSAL” in this manual and contact your local authorities for more information.
• The battery must be disposed safely in accordance with local ordinances or regulations.
• External adaptor and charging base:
  • Never use the external adaptor and charging base for anything other than charging the battery of the pool vacuum that is supplied in the same pack.
  • The external adaptor and charging base should not be used outdoors, nor should it be exposed to rain, humidity, and any liquid or heat.
  • The transformer ( or external adaptor) is to be located outside zone 1
  • Keep the external adaptor and charging base out of reach of children.
  • Never use the external adaptor and charging base if any damage is detected.
  •  DO NOT handle the external adaptor and charging base with wet hands.
  • DO NOT handle the pool vacuum, external adaptor, and charging base while charging with wet hands and without shoes.
  • Keep the external adaptor disconnected from power when it is not in use.
  • Never attempt to open the external adaptor and charging base.
  • If the supply cord of the external adaptor is damaged, the external adaptor must be replaced by the manufacturer or its service agent to prevent hazards of any kind.
  • Make sure the pool vacuum and the charging base are completely dry before charging.

CAUTION!

• This pool vacuum is designed for underwater use only; it is not an all-purpose vacuum cleaner. DO NOT attempt to use it to clean anything other than your pool / spa.
• Use only original accessories delivered with this product.
• DO NOT use this pool vacuum right after pool-shocking. It is recommended to leave the pool circulating for at least 24-48 hours.
• If you are planning on using the pool vacuum in a saltwater pool, make sure all salt are dissolved before deploying the pool vacuum.
• DO NOT use this pool vacuum with another automatic cleaner/cleaner simultaneously in the pool/spa.
• Avoid picking up hard, sharp objects with this product. They may damage the pool vacuum and filter.
• Exercise caution when cleaning pool stairs.
• To avoid damages to the external adaptor and charging base, do not attempt to carry the pool vacuum by the cord of external adaptor / charging base or pull the cord to disconnect it from the power source andcharging base.
• Charge the pool vacuum indoor in a clean, dry area with good ventilation and an ambient temperature between 5˚C (41˚F) and 35˚C (95˚F).
• DO NOT leave the pool vacuum charged for over 10 hours.
• If the pool vacuum will not be used for an extended period, detach it from the charging base and use a damp cloth to clean and dry the pool vacuum and accessories. Make sure to charge the pool vacuum to about 30% to 50% of the battery capacity before it is stored. Store in a well-ventilated area away from sunlight, heat, ignition sources, pool chemicals, and children. Never leave the pool vacuum plugged in for long-term storage. Recharge the pool vacuum every three months. Above warnings and cautions are not intended to incorporate all possible instances for risks and / or severe injuries. Pool / spa owners should always exercise extra caution and common sense when utilizing the product. Remark: Product/parts photos/drawings in this manual are for demonstration only.
  Product/parts in photos/drawings may vary with the model purchased. Accessories / parts shown in this manual & parts diagram are not necessarily included with every model.

GETTING STARTED

Charging the battery
IMPORTANT NOTE: Fully charge the pool vacuum (about 6 hs) before using it for the first time.
WARNING!

• Use only the original external adaptor and charging base provided.
• Make sure the pool vacuum and the charging contact plates are clean and dry before set-up and charging. (TIPS: Use a cotton bud to dry the charging contact plates)
• Charging must be done indoors, in a well-ventilated area away from sunlight, children, heat, ignition sources, and with an ambient temperature between 5˚C (41˚F) and 35˚C (95˚F).
• Never use the external adaptor and charging base if any damage is detected.
• The charging contact plates are waterproof. However, remnants of water on the contact plates could result in natural occurrence of stains (a byproduct of chemical reaction between water and electric currents). Otherwise, the stains can be removed by light scrubbing with a cotton bud soaked with juice of lemon or vinegar.
• Make sure that the pool vacuum is turned off prior to charging.

1. Place the unit on a flat surface. Make sure the pool vacuum is off by turning the power ON/OFF switch to the OFF position prior to charging.

2. Turn the locking knob (on each side) anticlockwise until it points to the green dot marking (unlock position) to unlock and release the rear body from the transparent canister.

3. Place the rear body (upside down – power on/off switch face up) on a flat surface. Align and slide the hook of the charging base onto the side notch at the bottom of the rear body until it stops. Make sure their contact plates are properly in contact. Plug the female jack of the external adaptor into the charging port at the end of the charging base.

4. Connect the external adaptor to the power source. Once the pool vacuum begins charging, the indicator light on the external adaptor will turn red. Normally, it takes about 5-6 hours to reach a full charge. The indicator light will turn green when the pool vacuum is almost fully charged.
   NOTE: if the motor is generating noise, ensure “OFF” is selected on the power switch.
   Immediately disconnect the external adaptor from the power source if you detect any of the following:

   • Offensive or unusual odor
   • Excessive heat
   • Deformation, cracks, leaks
   • Smoke

5. When charging is complete, disconnect the external adaptor from the power source and detach the charging base from the unit and external adaptor.
   Normally, the pool vacuum can operate up to 40 minutes on a full charge (charged for 5-6 hours)

   • Note: Clean the filter regularly. Too much debris inside the filter will increase burden to the motor operation and then shorten the operating duration. To re-position the transparent canister (with the filter cone inside) to the rear body, make sure the locking knob on both sides is turned to the unlock position. Align the raised arch on both sides of the transparent canister with the locking knobs and then turn the knob clockwise until it points to the red marking to secure the assembly.

   • Attention: The case has one correct position only. The water-draining valve must be facing the bottom when holding the cleaner horizontally by the handle.

   • FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a limited life and will gradually lose its capacity to hold a charge. Therefore, running time of the pool vacuum will gradually reduce through repeated charging and discharging in operation.

   • Once the lifespan of the battery reaches its end, refer to section “BATTERY DISPOSAL” for instructions regarding battery disposal

   • NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.

Set-Up Before Use

Handle assembly

• Insert the handle into the pool vacuum as shown, until the side pin on the handle is secured to the handle’s locking hole on the rear body.

• To release the handle, press down on the side pin and pull out the handle.

Telescopic pole (not included) assembly (only for EU & USA)

• Insert the end (with one side pin) of the pole connector into the pool vacuum as shown until its single side pin is secured to the handle’s locking hole on the rear body. Slide the telescopic pole into the pole connector until the side holes of the telescopic pole are secured to the side pins of the pole connector.

• To release the telescopic pole, press down on the two side pins simultaneously and pull out the pole

Specific Telescopic pole (not included) assembly (only for Australia & New Zealand)
Insert the end (with two side pins) of the pole connector into the pool vacuum as shown until its side pins are secured to the handle’s locking hole on the rear body. To install the telescopic pole (with internal wishbone clip) to the pole connector as shown:

Pool Preparation

• If there are stones, roots or metal corrosion in contact with the underside of the liner, discard them prior to using the pool vacuum. If necessary, seek assistance from a qualified professional.
• If the liner is brittle, damaged or wrinkled, contact a qualified professional to perform the necessary repairs or perform a liner replacement prior to using the pool vacuum.
• If you are using a saltwater pool, make sure all salt are dissolved before placing the pool vacuum into the water.

OPERATION

WARNING!

• Make sure the pool vacuum is off
• Do not use the pool vacuum if any damage is detected.
• Oil stain could occur due to possible leakage of lubricants applied to the O-ring.
• Do not operate this pool vacuum if there are people/pets present in the water.
• Make sure the pool vacuum is fully immersed in the pool before initiating operation. The minimum water level required to operate the pool vacuum must reach above the power ON/OFF switch of the pool vacuum when it is held in a vertical position. Operating the pool vacuum when it is not immersed correctly could damage the unit and void the warranty.
• DO NOT use the pool vacuum without an intact filter cone in place. Using your pool vacuum without an intact filter cone in place will VOID your warranty.
• DO NOT cover the side slot of the vacuum during operation. The impeller /motor may be damaged as a result.
• DO NOT leave the pool vacuum in the water when it is not in use.

1. Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in water and turn the power ON/FF switch to the ON position to initiate operation.
   CAUTION! Make sure the pool vacuum is always facing downwards when it is placed into the pool/spa. Otherwise it may bend the pole connector and damage it during the process.

2. To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing it downwards in order to allow water to escape from the outlet valve. Water is going to escape via the handle / pole connector and draining holes inside the handle chamber on the rear body.
   CAUTION! Make sure the pool vacuum is always facing downwards when it is removed from the pool/spa. Otherwise, the pole connector may be bent and damage the pool vacuum in the process

3. Rinse the pool vacuum with fresh water after every use. DO NOT use any detergent.

EMPTYING THE FILTER

WARNING! Using the pool vacuum without a filter cone in place will VOID your warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter cone before and after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the power source and detach the pool vacuum from the charging base. Make sure the pool vacuum is OFF

Emptying filter cone

1. Place the pool vacuum on a stable surface.

2. Turn the locking knob (on each side) anticlockwise until it is pointing towards the green marking to unlock and release the transparent canister. Remove the transparent canister from the rear body.

3. Tilt the transparent canister and make sure the smaller end is pointing upwards, then pull out the filter cone from the transparent canister. Hold the filter cone horizontally and turn its lid clockwise to detach it from the cone.

4. Rinse the transparent canister and clean out the debris inside the filter cone. It is recommended to clean the filter cone’s net with splashing water. If brushing is deemed necessary, use only a soft brush to clean it carefully and gently. DO NOT apply any pressure to the net.

5.  To lock the lid onto the filter cone, align the slot of the lid’s edge to the tab of the bottom part of the cone. Push the lid on the cone and turn the lid anticlockwise until it stops. Attach the filter cone to the transparent canister.
   CAUTION! Replace a damaged filter cone immediately with a new one before the next operation.

6. To re-position the transparent canister (with filter cone inside) onto the rear body, make sure the locking knob on each side is turned to the unlocked position. Align the raised arches on both sides of the transparent canister with the locking knobs and turn each knob clockwise until it points towards the red marking to secure the assembly. Attention: The case has one correct position only. The water-draining valve must be facing the bottom when holding the cleaner horizontally by the handle.

MAINTENANCE & STORAGE

NOTE:

1. Be sure to clean and dry the charging contact plates after every use to avoid the forming of stains (byproduct of a natural chemical reaction between electric current and water). Otherwise, the stains can be removed by light scrubbing with a cotton bud soaked with juice of lemon or vinegar.

2. Battery discharges on its own during storage. Make sure to charge the pool vacuum to about 30% to 50% of the battery capacity before it is stored.

3. You must re-charge the battery at least once every three months when it is not in use.

   • Unplug the external adaptor from socket and then unplug the adapter jack from the charging base.

   • Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and accessories with fresh water. DO NOT use detergent.

   • Make sure to drain the water from the rear body through the holes located inside the hamber that connects to the handle/ pole connector, and the hole on the rear of the body.

   • Make sure to drain the water from the handle through its hole on the bottom end.

   • Use a damp cloth to clean and dry the pool vacuum and its accessories.

   • Store them in a well-ventilated area away from the sunlight, children, heat, ignition sources, and pool chemicals. Ambient temperature for storage should be 10˚C – 25˚C (50˚F – 77˚F). NOTE: A higher temperature may reduce the battery life during storage.

WARNING!

• Never attempt in any way to disassemble the pool vacuum.
• Under no circumstances should you attempt to disassemble the pool vacuum and replace the impeller, motor and battery by yourself.

CAUTION!

• Excessive heat can damage the battery and reduce its lifespan as a result.
• Consult your dealer regarding battery replacement if the following happens:
  • Battery does not charge fully.
  • Battery operation time is noticeably reduced. Observe and record the run times of the first few operations (on a full charge). Use these run times as a reference point for comparison with run times in the future.
• The battery must be removed from the pool vacuum before it is scrapped.
• The pool vacuum must be disconnected from the supply mains when removing the battery
• The battery is to be disposed safely and according to local ordinances or regulations.
  NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a result.

BATTERY DISPOSAL

(To be carried out by an authorized technician) Your pool vacuum battery is a maintenance-free rechargeable lithium-ion battery pack, which must be disposed properly. Recycling is required; please contact your local authority for information.

WARNING!
Never attempt to disassemble a battery pack

• Remove all personal items such as rings, bracelets, necklaces and watches when the battery pack is unwired from the pool vacuum.
• A battery can produce a short circuit current high enough to weld a ring (or similar item) to metal, causing a severe burn in the process.
• Wear complete eye protection, gloves and protective clothing when the battery pack is being removed.
• Avoid touching the wires altogether and avoid allowing them to make contact with any metal items, which could cause sparking and/or short circuit the battery.
• Never smoke or allow a spark or flame in the vicinity of the battery or the pool vacuum.
• Do not expose the battery to fire or intense heat as this may result in an explosion.

CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged battery in a plastic bag.

• If leaking fluids come in contact with skin and clothing, wash immediately with plenty of soap and water.
• If leaking fluids come in contact with eyes, immediately flush eyes with cool running water for at least 15 minutes and do not rub them. Seek medical attention as soon as possible.

How to remove the battery pack for battery disposal only (To be done by authorized technician)
Recommended tools (not included): Philips screwdriver

1. Turn the locking knob (on each side) anticlockwise until it points to the green dot marking (unlock position) to unlock and release the rear body from the transparent canister.

2. Use the screwdriver to unscrew the 4 screws located on the top plate and then detach it from the rear body to expose the rear body’s cover.

3. Unfasten 6 screws and detach the cover to expose the PCBA, motor assembly, and battery pack.

4. To detach the battery connection wire, press the clip on the connector and then pull it out.

5. Unfasten the 3 screws to remove the battery compartment cover and then remove the battery pack. NOTE: Wrap the connector immediately with insulating tape in order to avoid short circuit caused by contact of both wire terminals.

TROUBLESHOOTING

battery again.
Impeller is jammed| Power off the pool vacuum and visually check the gap in middle of the pool vacuum to see if the impeller is jammed by larger debris. If possible, use a small tool to remove it with intensive care & caution. If necessary, contact your dealer for further instructions.

WARNING! Make sure the pool vacuum is

powered off when the unit is being serviced.

Impeller is broken| Contact your dealer for impeller replacement.
Filter is full| Clean the filter cone if applicable.
Larger debris / large volume of debris| Remove the pivoting suction head (not recommended for SPAs, vinyl liner and fibreglass pools as it could scratch the spa & pool surface.)
Debris escapes from the filter| Suction nozzle flap is broken| Suction nozzle flap works like a door to prevent the debris from escaping from the filter. Contact dealer for replacement parts and instruction.
Debris goes outside the filter cone| Filter net is damaged| Replace with a new filter cone.
Outlet valve comes off| Without the outlet valve, the pool vacuum might capture debris through this opening. Contact dealer for valve replacement.
Handle / pole connector cannot be secured in assembly| Side pin is broken| Replace with a new handle / pole connector.
Pool vacuum cannot be charged / recharged| Battery is damaged| Contact dealer for battery replacement.

WARNING! DO NOT open the pool vacuum

and replace the battery by yourself. This could result in severe or fatal injuries and the warranty will be voided as a result.

Contact plates of the charger base and unit are not connected.| Make sure that the charger base is assembled on the unit properly so that their contact plates are touching.
External adaptor is out of order| Contact dealer for replacement.

WARNING! Using the wrong external adaptor

will result in damaging the pool vacuum / battery and voiding the warranty as a result.

Pool vacuum is activated even though the switch indicates it’s off.| Presence of magnetic objects nearby has inadvertently switched on the motor.| Move the magnetic objects or vacuum away from each other.
Operation time is shorter as expected| Battery is not fully charged| Charge the pool vacuum for at least 6 hrs. NOTE: if any stains are found on the charging contact plates, remove them by using a cotton bud soaked with lemon juice or vinegar

Environmental Programmes, WEEE European Directive

• Please respect the European Union regulations and help to protect the environment. Return non-working electrical equipment to a facility appointed by your municipality that properly recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For items containing removable batteries, remove batteries before disposing of the product. © 2021 BWT Holding GmbH. 21010029
• All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of BWT Holding GmbH. (V1)

References

• Home - BWT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>