ENTHUZE ACTENT15010SSB Blackout Side Bar Installation Guide

ENTHUZE ACTENT15010SSB Blackout Side Bar Installation Guide

PARTS LIST

Washers
2| Passenger/Right Front/Rear Support Brackets| 8| 8mm Lock Washers
2| Compression Plates| 8| 8mm Hex Nuts

• Passenger/Right Front/Rear Support

• **Passenger/Right Center Support Bracket

**

• **Passenger/Right Rear Mounting Bracket

**

• **Passenger/Right Center Mounting Bracket

**

• **Passenger/Right Front Mounting Bracket

**

• **(2) Driver/Left Front/Rear Support Bracket

**

• **Driver/Left Rear Mounting

**

• **Driver/Left Center Mounting Bracket

**

• **Driver/Left Front Mounting Bracket

**

• Driver/Left Sidebar
  
  

PROCEDURE

1.  REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting under the Driver/Left side of the vehicle, remove the large plastic cover on the bottom of the floor panel, (Figure 1). Determine which plastic clips need to be removed. Carefully remove only the plastic clips for installation, (Figures 2 &3).

3. Locate the front mounting location, (Figure 4). Select (1) 10mm Spiral Bolt. Insert the Spiral Bolt into the side panel, (Figures 8A & 8B). Select (1) 10mm Short Bolt Plate. Insert the Bolt Plate into the floor panel, (Figure 9). Thread (1) 10mm Plastic Retainer onto the Bolt Plate to hold it in place.
   a. With the Spiral Bolt threads pointing away from the vehicle, insert the tail all the way up into the slot. Keep threads pointed outwards, (Figure 5).
   b. Slide in the bend in the tail up into the slot, keeping the threads pointed outwards, (Figure 6).
   c. Rotate Spiral Bolt downwards so that the threads are pointed towards the ground, (Figure 7).
   d. Follow link for 10mm Spiral Bolt installation. https://youtu.be/BqQis3QjZNc
   

4. Select the Driver/Left Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut, (Figure 10). Do not tighten hardware.

5. Select (1) Driver/Left Front/Rear Support Bracket. Attach the Support Bracket to the Spiral Bolt with (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut, (Figure 11). Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figure 12). Do not tighten hardware.

6. Move to the center location, (Figure 13). Insert (2) 10mm Spiral Bolts into the side panel, (Figure 14). Select the Driver/Left Center Support Bracket. Attach the Bracket to the (2) Spiral Bolts with (2) 10mm Flat Washers, (2) 10mm Lock Washers and (2) 10mm Hex Nuts, (Figure 15). Do not tighten hardware.

7. Select the Center Mounting Bracket. Attach the Mounting Bracket to the Support Bracket with (2) 8mm Hex Bolts, (4) 8mm Flat Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts, (Figure 16). Do not tighten hardware.

8. Select (1) Compression Plate.
   a. Thread (1) 10mm Hex Nut to (1) 10mm x 60mm Hex Bolt.
   b. Slide (1) 10mm Lock Washer and (1) 10mm Flat washer onto the 10mm Hex Bolt.
   c. Thread the 10mm Hex Bolt assembly into the welded nut on the back of the Mounting Bracket.
   Place the Compression Plate onto the end of the 10mm Hex Bolt, (Figures 17A & 17B).
   d. Tighten Hex Bolt to place the Compression Plate onto the floor panel. Do not tighten Hex Bolt all the way.
   NOTE: Use the 10mm Hex Nut to adjust the level of the Mounting Bracket.
   e. Follow link for Compression Plate installation. https://youtu.be/R51s7Vk1Sy4
   

9. 9. Move to the rear mounting location. Repeat Steps 3—5 to attach the Driver/Left Rear Mounting Bracket
   and (1) Driver/Left Front/Rear Support Bracket, (Figures 18—20). Do not tighten hardware.
   10. Select the Driver/Left Sidebar. With assistance, place the Sidebar onto the cradles of the Mounting
   Brackets. IMPORTANT: Do not slide or rotate Sidebar or damage to the finish may result. Attach the Sidebar to the (3) Mounting Brackets with (6) 8mm Combo Bolts, (Figure 21). Do not tighten hardware.

10. Level and adjust the Sidebar and tighten all hardware.

11. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
    To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
    Fig 1) Remove the plastic cover to reveal the floor panel and the plastic clips in the outer trim
    
    (Fig 2) Gently pull the trim slightly to loosen the clips (Passenger side shown)
    

Driver/Left Side Installation Pictured

Fig 3) Plastic clip removed from the front location trim (Passenger side shown)

(Fig 4) Locate the Driver/Left front mounting location

(Fig 5) Insert the tail on the Spiral Bolt into the slot, keeping the threads pointed outwards

(Fig 6) Insert the bend on the tail into the slot, keeping the threads pointed outwards

(Fig 7) Rotate the Spiral Bolt downwards

(Fig 8A) Insert (1) 10mm Spiral Bolt into the side panel

(Fig 8B) Follow link for 10mm Spiral Bolt installation.

https://youtu.be/BqQis3QjZNc

(Fig 9) Insert (1) 10mm Short Bolt Plate into the floor panel

(Fig 10) Attach the Driver/Left Front Mounting Bracket to the Bolt Plate

(Fig 11) Attach (1) Driver/Left Front/Rear Support Bracket to the Spiral Bolt

(Fig 12) Attach the Support Bracket to the Mounting Bracket

(Fig 13) Insert (2) 10mm Spiral Bolts into the outer center location

(Fig 14) (2) 10mm Spiral Bolts inserted into the outer center location

Fig 15) Attach the Driver/Left Center Support Bracket to the (2) 10mm Spiral Bolts

(Fig 16) Attach the Driver/Left Center Mounting Bracket to the Support Bracket

(Fig 17A) Use (1) Compression Plate to level the Bracket (Note use the Hex Nuts as adjusters)

(Fig 17B) Follow link for Compression Plate installation.

https://youtu.be/R51s7Vk1Sy4

(Fig 18) Example of the rear location (Passenger side shown)

(Fig 19) Insert (1) 10mm Spiral Bolt into the side panel and (1) 10mm Long Bolt Plate into the floor panel

(Fig 20) Attach the Driver/Left Rear Mounting Bracket to the Bolt Plate

(Fig 21) Attach the Driver/Left Sidebar to the Mounting Brackets

Documents / Resources

| ENTHUZE ACTENT15010SSB Blackout Side Bar [pdf] Installation Guide
ACTENT15010SSB, ACTENT15010SSB Blackout Side Bar, Blackout Side Bar, Side Bar, Bar
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>