NOVY Fusion 680 Filter Unit Instruction Manual

NOVY Fusion 680 Filter Unit

SAFETY AND ASSEMBLY REGULATIONS

Further information on Novy products, accessories and services may be found on the internet: www.novy.co.uk These are the installation instructions for the appliance as shown on the front. The directions for use are in a separate booklet supplied with the appliance. These installation instructions make use of a number of symbols. The meanings of the symbols are shown below.

Observe this instruction in order to prevent injury and damage to property.

Warnings before installation

• This appliance complies with the applicable safety instructions. However, inexpert installation may cause personal injury or damage to the appliance.
• The appliance is intended exclusively for household use (preparation of food) and excludes all other domestic, commercial or industrial use. Do not use the appliance outside.
• Check the condition of the appliance and the installation fittings as soon as you remove them from the packaging. Remove the appliance from the packaging with care. Do not use sharp knives to open the packaging.
• Do not install the appliance if it is damaged, and in that case inform Novy.
• The grease filters are in the appliance.
• Novy is not liable for damage resulting from incorrect assembly, incorrect connection, incorrect use or incorrect operation.
• The installation and electrical connection of the appliance should be left to a recognized expert.
• Safety is guaranteed only with expert installation in accordance with the installation manual. The installing technician is responsible for proper operation at the installation location.
• For easier installation of the appliance, it is advisable to carry it out with at least 2 people.
• Read the directions for use and the installation instructions before installing and using this appliance. You will find important information here for the assembly and use of the appliance.
• Metal parts may have sharp edges, and you may injure yourself on them. For that reason, wear protective gloves during installation.

Installation instructions for the appliance

• Ensure that the structure on or in which the appliance is to be installed can bear its weight.
• Faulty or damaged parts may only be replaced by original Novy parts.
• The larger the distance between the appliance and the hob, the less easily the cooking vapours can be taken up by the appliance. For this reason, pay heed to the stated (recommended) installation height.
• If a different distance is specified in the installation instructions for the gas hob, the largest distance in-dicated applies.
• In order to ensure that the cooking vapours are taken up in an optimal way, the appliance, or the structure into which the appliance is being installed, should extend over the hob. When using your own structure, ensure that the
• pliance is installed centred above the hob.
• For optimal operation, the hob should not be larger than the appliance or the structure into which the appliance is installed.

Exhaust or recirculation

Before starting to install, you need to have decided whether you are making an extraction duct to the outside, or whether you are going to use the extractor hood as a recirculation extractor hood. If opting for recirculation, you will find the recirculation kit with the accessories in these installation instructions.

Install the exhaust duct

For optimum performance of the cooker hood it is important to pay attention to the following points:

• The motor outlet has a diameter of 150 mm. It is recommended to connect an exhaust duct with a diameter of 150 mm to this.
• You will achieve the best operation and lowest possible noise level for the appliance by connecting the extraction duct by as short a route as possible, with as few bends as possible and using the prescribed diameter.
• Use smooth, non-flammable pipes with an internal diameter that is equal to the external diameter of the connection nozzle of the hood.
• Use flat duct with rounded corners and with air de-flectors. Available at Novy.
• Do not reduce the exhaust diameter. This will lower the capacity and raise the noise level.
• Avoid right-angle bends. Use rounded bends for effective airflow.
• The use of a flexible extraction hose should be kept to a minimum, and it should only be used for making small bridging sections, for example as the link between the outlet nozzle and the extraction duct. Maximally extend flexible ducts and cut them to size.
• Ensure that the extraction duct is not crushed and that there are no kinks in the duct.
• Use a hose clamp or aluminum tape for airtight connections.
• With a horizontal extraction duct, install it at a slight incline to ensure that condensation does not run back to the appliance.
• Condensation may arise as a result of temperature differences if the extraction duct passes through cool rooms. Ensure that the extraction duct is insulated.
• In case of an exhaust pipe through the outside wall passing a cavity wall, make sure that the exhaust duct fully bridges the cavity and slightly declines to the outside.
• In case of an exhaust pipe through the wall, use a wall vent.
• In case of an exhaust pipe through the roof, use a dou-ble-walled roof passage with adequate outlet capacity.
• hen connecting to a short extraction duct, it may be desirable to install a non-return valve in the duct in order to prevent backdraught from wind.
• Make sure that sufficient air is supplied. Fresh air can be supplied by slightly opening a window or an outside door or by installing an inlet grate.
• The appliance may not be connected to a flue or chim-ney that is currently in use, or that serves as ventilation for rooms with hearths.

Air supply

However large the kitchen or the room with open kitchen is, only so much air can be extracted from the room as is supplied. Too little air supply could result in a yield loss of 50% and more. If the extraction is used at the same time as a combustion system (for example heaters fired by gas, oil, wood or coal, hot water boilers using gas, gas hobs, and gas ovens), combustion gases may be sucked back in, and lead to poisoning. A combustion system uses air from the room as combustion air. Combustion gases arise as a result, which are removed to the outside by an extraction system. The appliance sucks in air from the kitchen and adjacent rooms.

Negative pressure occurs if the air supply is inadequate. The toxic gases are then sucked back from the chimney or extraction duct into the room. With simultaneous use of the appliance and combustion appliances in the same room, the negative pressure may not exceed 4 Pa (=0.04 mBar). Negative pressure can be prevented by allowing sufficient air into the room through openings that cannot be closed (for example through windows or doors, in combination with a ventilation cabinet in the wall). Have an expert assess the overall ventilation system in your home for a proposal on suitable measures in the area of air supply. When using the appliance with an internal or external motor (unit) with air extraction to the outside, there must be an adequate air supply in the room where the appliance has been installed/is positioned, so that fresh air can flow in. Fresh air can be provided by tilting a window, opening a door or installing an inlet grille. With an appliance with recirculation, there must be a minimum of ventilation in the room where the appliance has been installed/is positioned. Ventilation can be provided by the overall ventilation in the home or by tilting a window or opening a door. Certain appliances are fitted with a connection for a window contact switch (see the technical specifications for your appliance). If the appliance is to operate at the same time as a heating appliance that needs air from the room, and if the required supply can only take place through a single open window, there is the option of connecting the appliance to a window contact switch (not included). This ensures that the appliance operates only when the window is open. If the window is closed, the fan cannot be switched on. Contact your technician for the correct accessories for your appliance.

Installation instructions for the outlet

• The appliance may only be connected with the power plug to a socket with earth (230 V – 50 Hz).
• Safety is only assured when the appliance is connected to an earth cable in accordance with the instructions laid down.
• The appliance must be able to be disconnected from the power at any desired point.
•  Position the socket in such a way that the power plug of the appliance can be inserted easily.
• Do not use an extension cable for the connection to the electrical mains.
• Electric shock: never switch on a faulty appliance, this could cause an electric shock. Take the power plug out of the socket, or switch off at the distribution cabinet. Contact the Novy service department.
• Repairs and replacing faulty or damaged wiring must only be carried out by technicians who have undergone instruction by Novy.
• Moisture that has got into the appliance may cause an electric shock. Do not use a high pressure or steam cleaner.

ACCESSORIES

Recirculation
If you choose recirculation, Novy offers a monoblock recirculation filter which is placed in the hood. The monoblock filter is placed directly behind the grease filter. The exhaust grill to let the filtered air back into the kitchen must be provided by you.

Basic kit monoblock filter (without outlet box)

The exhaust grill to let the filtered air back into the kitchen must be provided by you. Minimum net opening of the exhaust grill: 177 cm².

• Circular exhaust tube length 1000 mm Ø150 mm 906.415
• Connection piece Ø150 mm 906.417
• Curve 90° Ø150 mm 906.416
• Aluminum external grill for Ø150 mm 906.178
• Wall conduct kit for ducting Ø150 mm including built-in heat retention-return valve 906.420
• Non-return valve Ø150 mm 906.432

Accessories flat exhaust duct

• Flexible exhaust tube length 750 mm 906.408
• Flat exhaust channel duct1000 mm (dimensions: 89x222x1000 mm) 906.401
• Connection piece (dimensions: 94x227x80 mm) 906.402
• Horizontal curve (dimensions: 94x227x290 mm) 906.403
• Vertical curve (dimensions: 94x175x227 mm ) 906.404
• Curve 15° (dimensions: 94x227x138 mm) 906.418
• Corner adapter (dimensions: 94x227x205 mm) 906.405
• Transition piece to Ø150 mm (dimensions: 94x227x190 mm) 906.406
• Wall conduct kit for for flat exhaust duct 89x222mm including built-in heat retention non-return valve 906.425
• Stainless Steel blind grill with non-return valve (dimensions: 290 x 160 mm) 906.407

General accessories

• Hose clamp adjustment Ø60-215 mm 906.291
• Aluminum tape roll 50 m 906.292
• Stainless steel cleaner: maintenance product for cleaning the stainless steel 906.060

InTouch
InTouch offers you the possibility to control the Novy cooker hood from the Novy InTouch induction cooking plate. The ceiling hood may, as a default, be combined with InTouch induction cooking plates.
Visit the website for the different models of induction cooking plates with InTouch.

Window switch
This hood is equipped with a connection for a contact window switch. If the hood is to work simultaneously with a heating appliance that pulls air from the room, and if the required supply of fresh air can only be through an open window, it is possible to connect a window contact switch (not supplied) to the hood. This ensures the hood only works if the window is open. When the window is closed, the fan can not be turned on. A window contact cable set is available as an accessory (part number 990.033). Using the cable set, it is possible to make a connection between the hood controller to the outside of the hood. A window contact switch can then be connected (not included).
Further information on Novy products, accessories, and services may be found on the internet: www.novy.co.uk

• Make sure there is a socket near the built-in unit, so that the power may, at all times, be removed from the built-in unit.
• Because of the substantial own weight of the hood, the construction must have sufficient load-bearing capacity.
• The glass adjustable flap opens forwards. The lighting is installed on the rear. Carefully look at the mounting drawings!

PAY ATTENTION TO THE FRONT AND REAR SIDES OF THE COOKER HOOD.

INSTALLATION

Assembly Preparation

• Model 680: installation in a 60 cm wide kitchen cupboard.
• Model 686: installation in a 90 cm wide kitchen cupboard.
• Cover the hob to avoid damage.
• The recommended mounting height for an induction, electrical or ceramic hob is at least 500mm and no more than 750mm. The mounting height for a gas hob is at least 650mm and no more than 750mm.
• Make a cut-out opening:
  • Type 680: cut-out 505 x 265mm
  • Type 686: cut-out 805 x 265mm
• Place the cooker hood as far as possible forward, at least 20 mm.
• The cooker hood is to be mounted in a kitchen cabinet (plate thickness at least 16 mm and maximum 35 mm).
• Make sure the cabinet door is not lower than the bottom of the cooker hood. Changing the exhaust direction of the motor (top/ rear)
• Change the position of the motor cover before installing the cooker hood.
• Loosen the 8 screws from the motor cover.
• Rotate the motor cover a quarter turn.
• Screw the motor cover back on.

Mounting the cooker hood
Press the cooker hood by the edges from underneath straight up into the kitchen cupboard until you hear a firm click. Pay close attention to the front and back of the cooker hood. The glass tilting cover opens to the front. The lighting is positioned at the back. Open the rotating glass panel and hand- tighten the 4 clamping screws. Take care not to over-tighten the screws. Close the rotating glass panel.

Place the exhaust pipe
Place the exhaust pipe on a connection nozzle of the motor using aluminum tape or a hose clamp. Put the plug into the wall socket. The lighting will work after 30 seconds.

Finishing of the hood

• When necessary you can fortify the front of cabinet. Make sure the hood is well aligned with the lower part of the cabinet.

Dimensions

• NOVY nv reserves the right at any time and without reservation to change the structure and the prices of its products.

NOVY nv

Noordlaan 6

• 8520 KUURNE Tel. 056/36.51.00 Fax 056/35.32.51
• E-mail: novy@novy.behttp://www.novy.behttp://www.novy.com
• France: Tél: 0320.940662
• Deutschland und Österreich: Tel: +49 (0)511.54.20.771 Nederland: Tel.: +31 (0)88-0119110
• United Kingdom : +44 (0)207 866 2493
• España: Tel.: +34 938 700 895
• Italia: Tel. : +39 039.20.57.501

References

• Der Spezialist für Dunstabzugshauben und Kochfelder - Novy
• Innovatieve dampkappen en intuïtieve kookplaten - Novy
• Specialist in cooker hoods and hobs - Novy
• Specialist in cooker hoods and hobs | Novy - Novy
• Spécialiste des hottes et tables de cuisson - Novy
• Specialist in stijlvolle afzuigkappen en kookplaten - Novy

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>