SEALEY LED1801 Rechargeable Slim Folding Inspection Light User Manual

SEALEY LED1801 Rechargeable Slim Folding Inspection Light

Product Information

Specifications

• Model No: LED1801 & LED1801K
• Battery Charging Time: 4 hours
• IP Rating: IP20
• LED Type: 12 SMD + 1W SMD (LED1801), 5W SMD + 1W SMD (x2) (LED1801K)
• Lumen Output: Side; 500lm, Top; 70lm (LED1801), Side; 1000lm, Top; 140lm (LED1801K)
• Maximum Length: 300mm
• Minimum Length: 155mm
• Operating Time: Side; 3 hours (500lm), Top; 8 hours (LED1801), Side/Top: 3/8 hours (LED1801K)

Product Usage Instructions

Safety

General

• Ensure that the lamp is fully charged before initial use.
• Do not turn the lamp on when it is being charged.
• Avoid shining the light directly into your, another person’s, or an animal’s eyes.
• Keep the lamp out of reach of children.
• Do not leave the battery in a discharged state; recharge it immediately.
• Recharge the battery at least once every six months of non-use.
• The lamp does not have any user serviceable components, so do not dismantle it.
• Avoid pulling the charger plug from the mains socket by the lead.

Battery Safety

• Do not attempt to open, disassemble, modify, or service the battery pack.
• Avoid crushing, puncturing, shorting external contacts, or disposing of the battery pack in fire or water.
• Recycle or dispose of used batteries as stipulated by local regulations.
• If the electrolyte in the cells gets on your skin, thoroughly wash with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

Introduction
This product is a 5W & 1W SMD LED Rechargeable Slim Folding Inspection Light. It can be used as a rechargeable floodlight or a folding inspection light. The kit includes a docking station for convenient charging.

Specification

• Model No: LED1801 & LED1801K
• Battery Charging Time: 4 hours
• IP Rating: IP20
• LED Type: 12 SMD + 1W SMD (LED1801), 5W SMD + 1W SMD (x2) (LED1801K)
• Lumen Output: Side; 500lm, Top; 70lm (LED1801), Side; 1000lm, Top; 140lm (LED1801K)
• Maximum Length: 300mm
• Minimum Length: 155mm
• Operating Time: Side; 3 hours (500lm), Top; 8 hours (LED1801), Side/Top: 3/8 hours (LED1801K)

Operation
Refer to the figures below for operation instructions:

Figure 1: Charge Indicator Lights Figure 2: End Torch Unit On/Off

Maintenance

1. General
   Before every use, check the lamp for any damage. If damage is observed, remove the lamp from use until it is repaired.

2. Battery
   The battery is not designed to be removed.

Environment Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Parts Support
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk , or telephone 01284 757500.

FAQ

• Q: How long does it take to charge the battery?
  A: The battery charging time is approximately 4 hours.

• Q: Can I use the lamp while it is being charged?
  A: No, it is not recommended to turn on the lamp while it is being charged.

• Q: Can children use the lamp?
  A: No, children should not be allowed to use the lamp.

• Q: How often should I recharge the battery?
  A: It is recommended to recharge the battery at least once every six months of non-use.

• Q: Can I dismantle the lamp?
  A: No, there are no user serviceable components, so the lamp should not be dismantled.

• Q: How should I dispose of used batteries?
  A: Used batteries should be recycled or disposed of as stipulated by local regulations.

5W & 1W SMD LED RECHARGEABLE SLIM FOLDING INSPECTION LIGHT
RECHARGEABLE FLOODLIGHT/FOLDING INSPECTION LIGHT DOCKING STATION KIT MODEL NO: LED1801 & LED1801K

• Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
• Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

SAFETY

GENERAL

• It is important to ensure that the lamp is fully charged before initial use.
• DO NOT turn the lamp on when it is being charged.
• DO NOT shine directly into your, another person’s or an animal’s eyes.
• DO NOT allow children to use the lamp.
• DO NOT leave battery in a discharged state. Recharge battery immediately.
• Recharge the battery at least once every six months of non-use.
• There are no user serviceable components. DO NOT dismantle.
• DO NOT pull the charger plug from the mains socket by the lead.

BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:

• DO NOT Attempt to open, disassemble, modify or service the battery pack.
• DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
• DO NOT Expose to temperatures above 60°C (140°F).
• Recycle or dispose of used battery as stipulated by local regulation.
• If the electrolyte in the cells gets on your skin, thoroughly wash with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

• LED1801:
  Slimline foldout inspection light for use in confined spaces, with 6mm minimum thickness. Inspection arm can be rotated 180° and folded back for use as a hands-free inspection light. Features 5W SMD LED which produce up to 500 lumens, operated by a rolling dimmer switch, and a 1W SMD LED in the end for use as a directional torch. Suitable for hands-free operation with three magnets and a hanging hook. Folds away, small and compact, suitable for keeping in your pocket. Can be charged in a Sealey docking station – LED1801K (not included). Powered by a 3.7V 2.6Ah rechargeable lithium-ion battery which lasts up to 8hr. Supplied with USB charging lead.

• LED1801K:
  Docking station kit includes 2 x LED1801 and charging station. Each inspection light has 5W SMD LED (side) + 1W SMD LED (top) producing up to 500 lumens. When both inspection lights are docked it can be used as a floodlight with two light options 50% and 100% producing 500 or 1000 lumens. Each inspection light can extend and is able to rotate 180° making it easy to direct the light. Two charging points with individual LED charging level indicators. Includes 5V~2A mains adaptor and 1m Micro USB charging cable.

SPECIFICATION

OPERATION

1. CHARGING

2. The battery fitted to this lamp is considered to be a consumable item and its ability to accept charge will reduce over time. We will warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the battery even if it is less than one year old.
   Note: The torches will flash when the battery gets low.

3.  Connect the charger into the charge socket on the lamp, see fig.1.
   Plug into power supply and turn on, the red charge LED on the lamp will light as the battery charges. When fully charged the LED turns green.

4. When the battery has fully charged (approx 3hrs) Disconnect from mains supply.
   Note: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without another charge.

5. Unfold lamp. Select either directional torch or inspection lamp. Brightness is controlled by dimmer switch.

6. Lamp can be hung from the hook or attached using magnets.

7. When the lamps are docked in the station (LED1801K) you can turn both of the docked torches on by using the On/Off button on top of the unit.

MAINTENANCE

1. Keep lamp clean and check for damage before every use. If damage is observed, remove from use until unit is repaired.
2. The battery is not designed to be removed .

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information. BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations).

• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
LED1801, LED1801K Issue 2 (H,2,3,F) 25/04/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>