i Safe MOBILE IS540.2 Non Incendive Smartphone Instructions

: June 16, 2024
: i safe MOBILE

Table of Contents

i Safe MOBILE IS540.2 Non-Incendive Smartphone
Product Information
Product Usage Instructions
Using Accessories
EX MARKINGS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

i Safe MOBILE IS540.2 Non-Incendive Smartphone

i Safe -MOBILE-IS540.2-Non-Incendive-Smartphone-
product

Product Information

Specifications

Model : IS540.2
Manufacturer: i.safe MOBILE GmbH
Address : i_Park Tauberfranken 10, 97922 Lauda-Koenigshofen, Germany
Contact : Tel. +49 9343 60148-0, info@isafe-mobile.com
Website : www.isafe-mobile.com
Version: 2023-11-16

EX Markings

EU Type Examination Certificate: EPS 23 ATEX 1 013 X

CE-designation

North America (NEC500 ):

Class I Division 2 Group ABCD T4
Class II Division 2 Group FG T4
Class III Division 2 T4 LR3081

Product Compliance for North America

Conforms to:

STD UL 60079-0
STD UL 60079-11
STD UL 913

Certified to :

CSA STD CSA C22.2 No. 60079-0
CSA STD CSA C22.2 No. 60079-11

Ex-Relevant Safety Regulations

Use of this device assumes that the operator observes the conventional safety regulations and has read and understood the Operating Manual, Safety Instructions, and certificate.

When used in explosion-hazardous areas, the following Safety Instructions must also be complied with:

Inside explosion hazardous areas the covers of all interfaces (USB, ISM Interface) must be closed.
Within explosion-hazardous areas, the following accessories may be used when connected to the ISM interface:
- The Headset IS-HS2A.1
- The Headset IS-HDHS1x.1
- The PTT Button IS-PTTB1A.1 together with the Headset IS-HDHS1x.1 The PTT Button IS-PTTB1A.1 without Headset IS-HDHS1x.1
- Other accessories approved by i.safe MOBILE GmbH The 16-pin ISM connector of the accessory must be securely fastened to the ISM interface.
If the PTT Button IS-PTTB1A.1 is connected to the ISM interface of the device together with the Headset IS-HDHS1x.1, the connection between the IS-PTTB1A.1 and the Headset ISHDHS1x.1 can be disconnected and reconnected in explosion hazardous areas.
When using the IS-PTTB1A.1 without the Headset IS-HDHS1x.1, the unused cable end of the IS-PTTB1A.1 may remain open in explosion hazardous areas.
When using accessories with Velcro fasteners (e.g. Headset IS-HDHS1B.1), the Velcro fastener may only be adjusted outside explosion hazardous areas.
To ensure the IP protection, it has to be ensured that all gaskets are present and functional. There must be no large gap between the two halves of housing and between the battery and housing.

Product Usage Instructions

Safety Instructions

When using the product, it is important to follow these safety instructions:

Observe conventional safety regulations
Read and understand the Operating Manual, Safety Instructions, and certificate
Covers of all interfaces (USB, ISM Interface) must be closed inside explosion hazardous areas

Using Accessories

Within explosion-hazardous areas, the following accessories may be used when connected to the ISM interface:

The Headset IS-HS2A.1
The Headset IS-HDHS1x.1
The PTT Button IS-PTTB1A.1 together with the Headset IS-HDHS1x.1
The PTT Button IS-PTTB1A.1 without Headset IS-HDHS1x.1
Other accessories approved by i.safe MOBILE GmbH

When using the accessories, make sure to :

Securely fasten the 16-pin ISM connector of the accessory to the ISM interface
If using the PTT Button IS-PTTB1A.1 with the Headset IS-HDHS1x.1, the connection between them can be disconnected and reconnected in explosion hazardous areas
If using the IS-PTTB1A.1 without the Headset IS-HDHS1x.1, the unused cable end of the IS-PTTB1A.1 may remain open in explosion hazardous areas
Adjust accessories with Velcro fasteners (e.g. Headset IS-HDHS1B.1) only outside explosion hazardous areas

Maintaining IP-Protection

To ensure the IP-protection of the device, follow these guidelines:

Ensure all gaskets are present and functional
Avoid large gaps between the two halves of the housing and between the battery and housing

FAQ

What should I do if there is a fault or damage to the device?
If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.
Where can I find the FCC/IC declaration?
The FCC/IC declaration can be found at www.isafe-mobile.com/en/support/downloads
Can I adjust the Velcro fastener of accessories inside explosion hazardous areas?
No, the Velcro fastener of accessories, such as the Headset IS-HDHS1B.1, should only be adjusted outside explosion hazardous areas.

EX MARKINGS

ATEX :

II 3G Ex ic IIC T4 Gc
II 3D Ex ic IIIC T135°C Dc
EU Type Examination Certificate:
EPS 23 ATEX 1 013 X
CE-designation:

IECEx :

Ex ic IIC T4 Gc
Ex ic IIIC T135°C Dc
IECEx Certificate: IECEx EPS 23.0003X

North America (NEC500):

Class I Division 2 Group ABCD T4
Class II Division 2 Group FG T4
Class III Division 2 T4
LR3081

Temperature range:

20°C … +55°C (EN/IEC 60079-0)
10°C … +55°C (EN/IEC 62368-1)

Manufactured by:

i.safe MOBILE GmbH
i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany

PRODUCT COMPLIANCE FOR NORTH AMERICA

Conforms to : STD UL 60079-0, STD UL 60079-11, STD UL 913
Certified to : CSA STD CSA C22.2 No. 60079-0, CSA STD CSA C22.2 No. 60079-11

EX-RELEVANT SAFETY REGULATIONS

Use of this device assumes that the operator observes the conventional safety regulations and has read and understood Operating Manual, Safety Instructions and certificate. When used in explosion hazardous areas, the following Safety Instructions must also be complied with:

Inside explosion-hazardous areas the covers of all interfaces (USB, ISM Interface) must be closed.
Within explosion hazardous areas, the following accessories may be used when connected to the ISM interface:
- the Headset IS-HS2A.1
- the Headset IS-HDHS1x.1
- the PTT Button IS-PTTB1A.1 together with the Headset IS-HDHS1x.1
- the PTT Button IS-PTTB1A.1 without Headset IS-HDHS1x.1
other accessories approved by i.safe MOBILE GmbH.
The 16-pin ISM connector of the accessory must be securely fastened to the ISM interface. If the PTT Button IS-PTTB1A.1 is connected to the ISM interface of the device together with the Headset IS-HDHS1x.1, the connection between the IS-PTTB1A.1 and the Headset ISHDHS1x. 1 can be disconnected and reconnected in explosion hazardous areas.
When using the IS-PTTB1A.1 without the Headset IS-HDHS1x.1, the unused cable end of the IS-PTTB1A.1 may remain open in explosion-hazardous areas.
When using accessories with Velcro fasteners (e.g. Headset IS-HDHS1B.1), the Velcro fastener may only be adjusted outside explosion hazardous areas. To ensure the IP-protection, it has to be ensured that all gaskets are present and functional. There must be no large gap between the two halves of housing and between the battery and housing.
The device may only be charged outside explosion hazardous areas using the charging equipment approved by i.safe MOBILE GmbH.
The microSD cards type IS-SD164.1 and IS-SD1128.1 or microSD cards which comply with the intrinsic safety entity parameters mentioned in the certificate, may be used in the corresponding slot in the hazardous area.
Nano-SIM cards which comply with the intrinsic safety entity parameters mentioned in the certificate, may be used in the corresponding slot in the hazardous area. The device may only be charged at ambient temperatures between 0°C … +45°C. The device may not be exposed to any aggressive acids or alkalis. The device may only be used in zones 2 or 22.

EX-RELEVANT SAFETY REGULATIONS FOR NORTH AMERICA

WARNING

The battery may only be charged and replaced outside of the hazardous area only.
Only charge the device using charging equipment approved by i.safe MOBILE GmbH.
The device must be protected from impacts with high impact energy, against excessive exposure to UV light and high electrostatic discharge.
The covers of all interfaces (USB, ISM interface) must be closed.
The device is intended to be carried over during use in the hazardous area.
The Headsets IS-HS2A.1, IS-HDHS1x.1 and the PTT Button IS-PTTB1A.1 or other accessories approved by i.safe MOBILE GmbH may be used within explosion hazardous areas only if connected to the ISM interface. The connector must be securely fastened to the ISM interface.
The microSD cards IS-SD164.1 and IS-SD1128.1 may be used in the corresponding slot in the hazardous area. Alternatively, the SD card port has the following intrinsic safety entity parameters:
Uo/Voc=4.35 V
Co/Ca=80 μF
Lo/La=1 μH

A commercially available microSD card may be used in the corresponding slot in potentially explosive atmospheres. The internal electrical capacitance and inductance are negligible, respectively correspond to the intrinsically safe connection parameters.

Nano-SIM cards which comply with the following intrinsic safety entity parameters, may be used in the corresponding slots in the hazardous area:
Uo/Voc=4.35 V
Co/Ca=80 μF
Lo/La=1 μH

A commercially available nano-SIM card may be used in the corresponding slot in potentially explosive atmospheres. The internal electrical capacitance and inductance are negligible, respectively correspond to the intrinsically safe connection parameters.

FAULTS AND DAMAGES

If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:

Malfunctions occur.
The housing of the device shows damage.
The device has been exposed to excessive loads.
The device has been stored improperly
Markings or labels on the device are illegible.

We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.

INFORMATION CONCERNING SAR CERTIFICATION

(SPECIFIC ABSORBATION RATE)

The SAR limit of Europe is 2,0 W/kg for the head and body, 4,0 W/kg for the limbs. The devicehas been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1,27 W/kg and when correctly worn on the body is 1,23 W/kg, limbs is 2,3 W/kg.

This device was tested for typical body worn operations with the back of the handset kept 5 mm from the body. The device complies with RF specifications when used at 5 mm from the body. Belt clips, holsters and similar accessories used should not contain metallic components in the assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided.

FCC/IC STATEMENT

The FCC/IC declaration can be found at www.isafe- mobile.com/en/support/downloads

MAXIMUM OUTPUT POWER

| AT| BE| BG| CH| CY| CZ| DE
---|---|---|---|---|---|---|---
DK| EE| EL| ES| FI| FR| HR
HU| IE| IS| IT| LI| LT| LU
LV| MT| NL| PL| PT| RO| SE
SI| SK| TR| UK| | |

Restrictions in the 5 GHz band:

According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE), Bulgaria (BG), the Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), the United Kingdom (UK), Turkey (TR), Norway (NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI). The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5850 MHz frequency range.

EU Declaration of Conformity

according to directive 2014/34/EU, 2014/53/EU, 2011/65/EU (2015/863/EU)

The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards: