Ten Pao Precision Electronics DMI-WP-ANC-001 Precision Anchor Instruction Manual
- June 4, 2024
- Ten Pao Precision Electronics
Table of Contents
INSTRUCTION MANUAL
Please keep reading the following safety notes before use or examination.
Product description.
- This product is a component that can detect the environment temperature, humidity, atmospheric pressure, etc, and then send the detected information to the server through Bluetooth access to the network.
- Based on DMI-WP-ANC-001; S001CEN0330010; DMANWPWMHWXX, this product adds the infrared sensor and light sensor of human body, as well as the DIMMING dimmer that controls the LED lamp. For example, when someone is detected and the ambient light is dark, the corresponding LED lamp will be adjusted to the corresponding brightness.
- : FOR INDOOR USE ONLY.
- This product is used for internal temperature measurement in office.
Warning.
- If the device is connected to a voltage beyond a specified range(e.g.380V), it will cause damage to the device.
- If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be damaged.
Technical parameter.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Model: DMI-WP-ANC-001;S001CEN0330010;DMANWPWMHWXX
Product name: PRECISION ANCHOR
Suppliers Name: DMI, LLC
Suppliers Address (USA)： 850 White St, Dubuque, IA 52001-7035, US
Suppliers’ internet contact:
www.precisionreality.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
1. Input: 100-277Vac 50/60Hz
Black: AC-Live 10A/White: AC-Neutral 0.1A
Use ambient temperature 0-40℃ ,humidity 10-90%,altitude 2000m,overvoltage
grade
II,pollution
grade III
Installation
The device is fixed and installed through a 1/2” thread interface. The black and white wires are respectively connected to the fire line and the zero line of the mains power supply. The fire line of the mains power supply shall be equipped with a switch of no less than 10A/25V.
Operation instruction.
The Bluetooth chip detects the ambient temperature and humidity via IC2 or IC4
and then
uploads to the server via the Bluetooth network.
Equipment maintenance and service.
- Check whether the indicator light of the device is on or the Bluetooth is enabled to determine whether the device is working.
- Maintenance of equipment. If the indicator light of the equipment is not on or the Bluetooth is not working, the equipment can be powered on again after powering off.
- When something goes wrong with the product, if you can’t fix it yourself, send it back.
- If the product is damaged, please send it back.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Manufacturer name: TEN PAO PRECISION TECHNOLOGY (HUIZHOU) COMPANY LIMITED
Address: Block A, 27 Xianghe Avenue, Dongjiang Industrial Zone, Shuikou
Street Office, Huicheng District, Huizhou City, Guangdong Province, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>