Spectrum 441D Sauna White Light System Instruction Manual

June 16, 2024
SPECTRUM

Spectrum 441D Sauna White Light System

Product Information

Specifications

  • Product Name : Spectrum 441D Sauna White Light System
  • Installation and Operation Manual: Included
  • Installation Considerations: Read the manual before installation
  • Electrical Components: Not hot-swappable
  • Safety: Use safety goggles during installation
  • Warranty: Void if electrical components are hot-swapped
  • Wiring: Must be done by the National Electric Code and local building code
  • Installation: Should be done by a licensed, qualified electrician
  • Light Placement: Avoid direct contact with the bather’s eyes
  • Risk of Uninsulated Electrical Connections: Use insulating gloves if necessary

Package Includes

Item Quantity Description
A 1 Driver
B 1 Enclosure
C 2 Strain Relief Bushings
D 1 Male NEMA Cable
E 1 Light Cable
F 1 Cat6 Cable, 1′
G 1 Cat6 Cable, 25′
H 1 Output Box
I 1* Mounting Template
J 1* Brilliance Light Fixture
K 1* Wire Fit Cap
L 1 Dimmer

Installation Instructions

Please read the manual entirely before installation. Carefully review all installation options and instructions before proceeding. Use safety goggles for safety purposes.

Important Safety Instructions

  • Do not hot-swap any electrical components. This will void the warranty and likely cause the product to fail.
  • Fully disconnect the system from its power source before swapping any electrical components.
  • The Spectrum 441D Sauna White Light System should be installed by a licensed, qualified electrician.
  • Check for piping/electrical before cutting or drilling.
  • Some electrical components are not waterproof.
  • If there is any risk of uninsulated electrical connections in your wall/ceiling area, use insulating gloves.

Light Placement

Consider light placement carefully. The fixture(s) for this system should be placed to avoid direct contact with the bather’s eyes.

Installation Steps

  1. Choose a desired switch location for the Spectrum 441D Sauna White Light System. The switch must be placed outside the sauna and should not be reachable from a tub or shower.
  2. Allow for at least 2 inches of clearance from insulation above and around the fixture.
  3. Ensure all wiring is done by the National Electric Code and local building code.
  4. Install the driver (Item A) and enclosure (Item B) using the provided screws and anchors.
  5. Attach the strain relief bushings (Item C) to secure the wires.
  6. Connect the male NEMA cable (Item D) to the electrical outlet and the driver (Item A).
  7. Connect the light cable (Item E) to the driver (Item A) and the brilliance light fixture (Item J).
  8. Use the provided wire nuts (Item A) to secure the connections.
  9. Mount the dimmer (Item L) in a suitable location.
  10. Connect the output box (Item H) to the light cable (Item E) using a 1′ Cat6 cable (Item F).
  11. Connect the output box (Item H) to the driver (Item A) using another 1′ Cat6 cable (Item F).
  12. Follow the electrical diagram provided to set the DIP switches (Item A/B) accordingly.
  13. Ensure that the power source is physically unplugged before swapping any electrical components.

Frequently Asked Questions

Q: Can I hot-swap the electrical components of the Spectrum 441D Sauna White Light System?

  • A: No, hot-swapping any electrical components will void the warranty and likely cause the product to fail.
  • Always fully disconnect the system from its power source before swapping any electrical components.

Q: Who should install the Spectrum 441D Sauna White Light System?

  • A: The system should be installed by a licensed, qualified electrician to ensure proper installation and adherence to safety regulations.

Q: What should I do if there is a risk of uninsulated electrical connections in my wall/ceiling area?

  • A: If there is any risk of uninsulated electrical connections, it is recommended to use insulating gloves during installation to ensure safety.

Q: Can the light fixtures be placed directly in contact with the bather’s eyes?

  • A: No, the light fixtures should be placed to avoid direct contact with the bather’s eyes for safety reasons.

Installation Considerations

  • Please read this manual in its entirety before installation
    IMPORTANT: DO NOT HOT-SWAP ANY ELECTRICAL COMPONENTS. This will void the warranty, and likely cause the product to fail.

  • Carefully review all installation options and instructions before proceeding.

  • For safety purposes, use safety goggles at all times.

  • Do not hot-swap any electrical components. This will void the warranty, and likely cause the product to fail. Fully disconnect the system from its power source before swapping any electrical components.

  • Check for piping / electrical before cutting or drilling.

  • Some electrical components are not waterproof.

  • If there is any risk of uninsulated electrical connections in your wall/ceiling area, use insulating gloves.

  • The Spectrum 441D Sauna White Light System can be controlled by the use of a light switch provided by others. NEVER place a switch where it can be reached from a tub or shower.

  • All wiring must be done under the National Electric

  • Code and local building code.

  • The Spectrum 441D White

  • Light System should be installed by a licensed, qualified electrician.

  • IMPORTANT Consider light placement carefully. The fixture(s) for this system should be placed to avoid direct contact with the bather’s eyes.

Installation

Package Includes

Item Quantity Description
A 1 Driver
1 Screw
1 Locknut
B 1 Enclosure
1 Enclosure Top
Item Quantity Description
--- --- ---
2 Enclosure Top Screws
4 Screws / Anchors
4 Wire Nuts
1 Ground Connector
C 2 Strain Relief Bushings

IMPORTANT: DO NOT HOT SWAP ANY ELECTRICAL COMPONENTS PHYSICALLY UNPLUGFROM POWER SOURCE BEFORE SWAPPING ELECTRICAL COMPONENTS

Item Quantity Description
D 1 Male NEMA Cable
E 1 Light Cable
F 1 Cat6 Cable, 1’
G 1* Cat6 Cable, 25’
H 1 Output Box
Item Quantity Description
--- --- ---
D 1 Male NEMA Cable
E 1 Light Cable
F 1 Cat6 Cable, 1’
G 1* Cat6 Cable, 25’
H 1 Output Box
  • NOTE: Quantity with an * increases by one per each additional light purchased.
  • The quantities shown assume no additional lights were purchased with the Spectrum 441D system.

Electrical Diagram

NOTE: Neutral from the Electrical Panel is not needed for the Dimmer, but passes through to the Electrical Outlet.

Electrical Detail

  1. Electrical Panel to Dimmer (L)
    • a) The Dimmer (F) will make use of a 120VAC, 15 Amp branch circuit. The Dimmer (L) should be placed where most convenient for operation.
    • The Dimmer (L) must be installed outside the Sauna Room. Never place a switch where it can be reached from a tub or shower.
    • ELECTRICAL PANEL ———-> DIMMER (L)
    • Ground Ground
    • Neutral (passes through to Outlet)
    • Hot Black
  2. Dimmer (L) to Electrical Outlet
    • a) DIMMER (L) ———–> ELECTRICAL OUTLET
    • Ground Ground
    • (Neutral from Panel) Neutral
    • Red Hot
  3. Driver (A) to Dimmer (L)
    • a) DRIVER (A) ———-> DIMMER (L)
    • Blue Purple
    • White Gray

IMPORTANT: DO NOT HOT-SWAP ANY ELECTRICAL COMPONENTS. This will void the warranty, and likely cause the product to fail.

  1. Install a standard single-gang electrical box in an accessible, dry location.
  2. Run a grounded 120VAC from the power supply to the accessible, dry location ’s electrical box.
  3. Secure enclosure (B) to the wall in an accessible, dry location using provided screws/anchors.
  4. Determine the number of lights per input. Limit 6 lights per input.
  5. Determine desired brilliance light fixture (J) location. Note: Fixture should be placed to avoid direct contact with the bather’s eyes.
    • Allow for 2” clearance from insulation above and around the fixture.
  6. Optional: Mount 16” location template (I) to ceiling/wall framework. Use notches to quickly align the desired location to other fixtures in the room.
  7. Make a 1-5/8” hole in the desired location.
  8. Mount brilliance light fixture (J) to the ceiling through 1-5/8” cut-out. Allow for 2” clearance from insulation above and around the fixture.
  9. Repeat steps 6 – 8 for each light.

Product Care

  • For routine cleaning, simply use a soft damp cloth and common household soap. Use a damp cloth to wipe clean, then dry.
  • Clean product frequently to avoid calcium deposits on surfaces.
  • Use only mild soap.
  • Never use abrasive or cleaning containing alcohol, ammonia, hydrochloric, or phosphoric acids as they may damage the product’s finish.
  • To clean electrical components, gently wipe down using a dry cloth or duster.
  • Never use a wet duster, water, or any other liquid to clean the device.

Specifications

Driver

  • Operating Voltage: 120 V AC
  • Output Voltage: 700mA
  • Power Consumption: 35W Nominal
  • Amperage: 1.1 Amps Dimensions: 5-7/8” W x 1-1/8” H x 1-5/8” D

Brilliance Fixture

  • Type: LED White 3500K
  • Operating Voltage: 12VDC
  • Maximum Input Current: 700mA
  • LED: 1 x 3 Watt
  • Beam Angle: 35°
  • Trim Finish: Polished Stainless Steel
  • Housing Composition: First Grade Aluminum
  • Lens: Frosted, 1-7/32” Diameter
  • Lens Composition: Tempered Glass
  • Rough-in Cutout: 1-5/8” to 1-11/16”
  • Trim Dimension: 2-3/64” Diameter, 1/8” Profile
  • Body Dimensions: 1-15/32”
  • Diameter x 1-7/8” Deep
  • Rating: IP68
  • Certifications: CE / RoHS / WEEE
  • Max Operating Temperature: 220°F when installed per instructions

Enclosure

  • Housing Composition: Steel, black powder-coated finish
  • Dimensions: 7-3/4” W x 1-7/8” H x 4-7/8” D
  • Standards: NEMA 1
  • Listing: ETL, UL

Construction Template

  • Composition: Steel, Galvanized, Gauge 22
  • Dimensions: 15-1/8” L x 1/32” H x 3” D

Replacement P arts

Contact your Bathology representative for Spectrum 441D Sauna White Light System replacement parts. 800-957-2862 www.Bathology.com

Description Part Number
Driver Spectrum114
Enclosure Spectrum079
Strain Relief Bushings Spectrum077
Male NEMA Cable Spectrum038
Cat6 Cable, 1’ Spectrum030
Cat6 Cable, 25’ Spectrum031
Splitter Spectrum071
Mounting Template Spectrum-68- Temp
Frosted LED White Light Spectrum107

Documents / Resources

| Spectrum 441D Sauna White Light System [pdf] Instruction Manual
441D Sauna White Light System, 441D, Sauna White Light System, White Light System, Light System, System
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals