martec MSDC133M Scorpion DC Ceiling Fan Installation Guide
- June 16, 2024
- martec
Table of Contents
martec MSDC133M Scorpion DC Ceiling Fan
Product Information
Specifications
- Models Parameters (Fan Only):
- MSDC133M – 1320mm 3 Blade Ceiling Fan Matt Black
- MSDC133W – 1320mm 3 Blade Ceiling Fan Matt White
- MSDC133GC – 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- MSDC103M – 1050mm 3 Blade Ceiling Fan Matt Black
- MSDC103W – 1050mm 3 Blade Ceiling Fan Matt White
- MSDC103GC – 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- Models Parameters (Fan and LED Light):
- MSDC1333M – 1320mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1333W – 1320mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1333GC – 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
- MSDC1033M – 1050mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1033W – 1050mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1033GC – 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
Part List
- 1x motor assembly
- 1x hanging bracket
- 1x instruction manual
- 1x wall control kit
- 1x screw kit
- 3x blades
- 1x balancing kit
Application
The fan can be installed on a flat surface or ceiling. It is suitable for
use on corrugated ceilings and apex ceilings.
Product Usage Instructions
Assembly
-
Step 1: Align the bracket and screw the hanger bracket to the ceiling tightly.
-
Blade Installation (Fan Only)
Step 1: Attach the blade to the top of the motor using the 2 screws provided. Tighten the screws and repeat this procedure for all blades. -
Blade Installation (Fan and LED Light)
Step 1: Attach the blade to the top of the motor using the 2 screws provided. Tighten the screws and repeat this procedure for all blades. -
Fan Installation
Step 1: Place the fan into the hanger bracket and align the ball joint slot with the hanger bracket. -
Step 2: After wiring is completed, attach the canopy to the hanger bracket by pushing upwards and twisting anti-clockwise. Tighten screws and ensure the canopy is not touching the ball joint.
-
LED Light Plate Installation
Step 1: Install the LED light kits as illustrated. -
Cover Installation/Removal (Fan Only Model)
Step 1: Take out the button cover and turn it clockwise against the motor bearing belt thread until it is locked. -
Receiver Remote Control Installation
Step 1: Wire up the receiver with quick connectors and insert it into the mounting bracket. Make sure the antenna wire has been connected without cutting it. -
WiFi / Remote Control Pairing (Fan Only Model)
Step 1: Turn on the ceiling fan.
FAQ
-
Q: What models are available for the Avoca DC Series ceiling fan?
A: The Avoca DC Series ceiling fan is available in various models, both with and without LED lights. The models include:- MSDC133M – 1320mm 3 Blade Ceiling Fan Matt Black
- MSDC133W – 1320mm 3 Blade Ceiling Fan Matt White
- MSDC133GC – 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- MSDC103M – 1050mm 3 Blade Ceiling Fan Matt Black
- MSDC103W – 1050mm 3 Blade Ceiling Fan Matt White
- MSDC103GC – 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- MSDC1333M – 1320mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1333W – 1320mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1333GC – 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
- MSDC1033M – 1050mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1033W – 1050mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1033GC – 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
-
Q: Can the fan be installed on different types of ceilings?
A: Yes, the fan can be installed on flat surfaces, corrugated ceilings, and apex ceilings. -
Q: How do I install the blades?
A: To install the blades, follow these steps: -
For fan-only models: Attach the blade to the top of the motor using the provided screws. Tighten the screws and repeat for all blades.
-
For fan and LED light models: Follow the same steps as above to install the blades.
-
Q: How do I install the fan?
A: To install the fan, follow these steps: -
Place the fan into the hanger bracket and align the ball joint slot with the hanger bracket.
-
After wiring is completed, attach the canopy to the hanger bracket by pushing upwards and twisting anti-clockwise. Tighten screws and ensure the canopy is not touching the ball joint.
-
Q: How do I install the LED light plate?
A: To install the LED light plate, follow these steps: -
Attach the LED light kits as illustrated in the manual.
-
Q: How do I install/remove the cover for fan-only models?
A: To install or remove the cover, follow these steps: -
Take out the button cover and turn it clockwise against the motor bearing belt thread until it is locked.
-
Q: How do I install the receiver for remote control?
A: To install the receiver for remote control, follow these steps: -
Wire up the receiver with quick connectors and insert it into the mounting bracket. Make sure the antenna wire has been connected without cutting it.
-
Q: How do I pair the remote control with the fan?
A: To pair the remote control with the fan, follow these steps: -
Turn on the ceiling fan.
SCORPION DC Series Installation Guide
Thanks for choosing our Avoca DC Series ceiling fan. We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
- MSDC133M
- 1320mm 3 Blade Ceiling Fan Matt White
- MSDC133W
- 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- MSDC133GC
- 1050mm 3 Blade Ceiling Fan Matt Black
- MSDC103M
- 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre
- MSDC103W
Models Parameters (Fan and LED Light):-
- MSDC1333M
- 1320mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1333W
- 1320mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1333GC
- 1320mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
- MSDC1033M
- 1050mm 3 Blade Ceiling Fan Matt Black with 20W LED Light
- MSDC1033W
- 1050mm 3 Blade Ceiling Fan Matt White with 20W LED Light
- MSDC1033GC
- 1050mm 3 Blade Ceiling Fan Matt Silver/Carbon Fibre with 20W LED Light
Part List
- Qty 1x motor assembly
- Qty 1x hanging bracket
- Qty 1x instruction manual
- Qty 1x wall control kit
- Qty 1x screw kit
- Qty 3x blades
- Qty 1x balancing kit
Application
How to Assemble
How to Install Blades
Fg.3 Fan only models
- Attach the blade to the top of the motor using the 2 screws provided. Tighten the screws and repeat this procedure for all blades.
- NB: Ensure the blades do not get damaged or bent during the installation process while the fan is on the ground. This will act the performance and balance of the fan and this is NOT covered under warranty.
How to Install Blades
Fg.4 Fan LED Light Model
Attach the blade to the top of the motor using the 2 screws provided. Tighten
the screws and repeat this procedure for all blades.
How to Install
How to Install Light Plate
Fg.7 Fan LED Light Model
Install the LED light kits as illustrated above.
How to Install / Remove the Cover
- Take out the button cover and turn it clockwise against the motor bearing belt thread until it is locked.
- Align the convex point on the light plate with the gap on the LED mounting plate and press down firmly.
Installing Receiver Remote Control
- Wire up the receiver with quick connectors and insert into Wire up the receiver with quick connectors and insert into the mounting bracket. Make sure the antenna wire has been the mounting bracket. Make sure the antenna wire has been safely folded inside the canopy cover before final assembly. (DO NOT cut the antenna wire)
Important Reminders
- Receiver must be correctly installed in the mounting bracket
- When the transmitter cannot control the receiver, please check
- has sufficient battery in the transmitter
- any existence of similar remote controlled products nearby that cause interference Replace battery if getting low as this will affect sensitivity of the transmitter
- Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
- Isolation switch MUST be connected in the line
WiFi / Remote Control Pairing
Fan only model
Pairing the remote control
- Turn on the ceiling fan.
- Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.
If you don’t hear a “beep” sound, repeat step 1 and step 2 again.
Entering WiFi Pairing mode :
- Turn on the power.
- Within the first 20 seconds, press and hold the” ” button until a “beep” is heard.
- Continue step connect on your smart devices to complete the pairing. 1h 11I m
- If you don’t hear a “beep” sound, repeat the above steps.
- FAN OFF ****: to switch off the fan.
- SLEEP MODE : Turn on the fan at an extra lower speed to create a general breeze.
- SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
- NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
- FORWORD AND REVERSAL : summer/winter reverse mode.
- TIMER 1H/4H/8H : preset timer for fan and light to stop automatically. ie. if timer set at 1H and then press 4H, fan will stop at 4H. Setting default to last press.
- WIFI BUTTON :Follow the instructions and press and hold for 20 seconds to enter wifi matching mode.
Fan LED Light Model
Pairing the remote control
- Turn on the ceiling fan.
- Within the first 20 seconds, continue pressing the ****button until you hear a “beep” sound. ie. It is paired.
If you don’t hear a “beep” sound, repeat step 1 and step 2 again.
Entering WiFi Pairing mode:
- Turn on the power.
- Within the first 20 seconds, press and hold the ” ” button until a “beep” is heard.
- Continue step connect on your smart devices to complete the pairing. 1h 4 III m If you don’t hear a “beep” sound, repeat the above steps.
- FAN OFF : to switch off the fan.
- SLEEP MODE : Turn on the fan at an extra lower speed to create a general breeze.
- SPEED BUTTON : 1 = lowest speed. 6 = highest speed.
- NATURAL WIND MO D E : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
- FORWORD AND REVERSA L : summer/winter reverse mode.
- TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if timer set at 1H and then press 4H, fan will stop at 4H. Setting default to last press.
- LIGHT ON/OFF : to switch off the light. CCT : warm white (2700K) / natural white (4000K) / cool white (6500K) LED- LED+: minus ” = reduces brightness plus “+”= increases brightness’
WARNING
- Installation of fans MUST follow SAA standards and meet local authority regulations.
- Installation MUST be carried out by a qualified and licensed electrician.
- Fan and light MUST be earthed. Bracket MUST be firmly attached to a flat solid structure or timber frame.
- DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
- The warranty is VOID if product is not installed according to this installation guide.
Smart Life matching process, please follow the steps:
-
Download the “Smart Life” APP on your smart devices by scanning the QR code below with camera.
-
Turn on WiFi and Bluetooth on your smart devices. Ensure it’s connected to a 2.4GHZ WiFi.
-
Open the APP, follow the steps to register new user account or login existing account.
-
Follow instructions in main manual (steps can also be found on the back of the remote) to put the fan into WiFi pairing mode. If the operation is successful, go to step 5. If the fan has previously been paired or you can’t get it to work, please go to step 4 to RESET the fan.
-
RESET the fan. This step is NOT necessary if the fan has successfully entered WiFi pairing mode in the last step, if not, try to RESET the fan: turn on the fan, power off after 10 seconds, power on again after 15 seconds, long press “Fan Stop” for 5 seconds, if “beep beep” are heard, the reset is successful. If “beep beep” is not heard, the reset is failed, please repeat this step.
-
Once the fan has entered WiFi pairing mode, open the APP again on the smart device. Click “Add Device” in the middle or the “+” on the top right of the screen.
-
The auto scan should begin automatically, and the fan should show up at the top of screen within a few seconds.
Note: If the fan is not showing up, you can add it manually by clicking and navigate to: >Add Manually >Small Home Appliance > Fan -
Follow instructions in the APP to finish the set up.
- E: sales@martecltd.com.au
- P: 02 8778 7500
- www.martecaustralia.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>