SEALEY MK61.V2 Spray Booth Stand Instruction Manual

: June 16, 2024
: SEALEY

Table of Contents

SEALEY MK61.V2 Spray Booth Stand
Product Information
Product Usage Instruction
SAFETY
INTRODUCTION
SPECIFICATION
ASSEMBLY
OPERATION
Warranty
Contact Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY MK61.V2 Spray Booth Stand

SEALEY-MK61.V2-Spray-Booth-Stand-product

Product Information

Specifications

Model No: MK61.V2
Height: 1105mm
Width: 850mm

Introduction
Ideal for holding small vehicle body parts such as grilles, spoilers, wings, and mirror housings during preparation and spraying.

Product Usage Instruction

Assembly

Check the contents against Fig. 1 and the parts list to confirm that all are present, and to familiarize yourself with the parts.
Mount base tubes (short) (1) onto the bottom cross tube (6), using screws (5), washers (2), and nuts (3) to tighten.
Put knob (7) into the base tube ready to receive the upright (8), insert the upright, and tighten the knob (7).
Fit top cross tube (11) and secure with a knob (7).
Fit set plates (10) onto the ends of the top cross tube (11) secure with knobs (7) and fit plugs (9) on each end.
Fit the four adjusting screws (4) into the bottom of the base tubes (1) and adjust them until the stand is level.

Operation

Loosen the knobs and adjust the position of the cross tube and set plates as required.
If required, secure the help of a second person, and lift the vehicle panel into position, find a suitable feature to rest it on.
If further security is required, use chains or similar to attach to a suitable feature on the panel and stretch the chain to the set plates.
DO NOT let go of the panel until you are sure that it is properly secured.
Retighten the knobs to lock them.
Check that the panel is stable before moving the stand.

Environment Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

FAQ

Q: Can I use this spray booth stand for larger vehicle body parts?
A: No, this spray booth stand is designed for holding small vehicle body parts such as grilles, spoilers, wings, and mirror housings.
Q: Can I use this stand on uneven surfaces?
A: No, it is recommended to use the stand on level and solid ground, preferably concrete.
Q: How should I store the stand when not in use?
A: Store the stand in a safe, dry, childproof location to ensure its best and safest performance.
Q: What should I do if any parts are damaged or missing?
A: Do not use the stand if any parts are damaged or missing, as this may cause failure and/or personal injury. Contact the manufacturer for authorized replacement parts.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

Familiarise yourself with the application and the limitations and potential hazards of the stand.
Maintain the stand in good condition, use authorized replacement parts only.
Locate the stand in a suitable, clean work area.
Keep the work area clean, and uncluttered and ensure that there is adequate lighting.
WARNING! Use the stand on level and solid ground only, preferably concrete.
DO NOT overload the stand.
DO NOT climb on the stand.
DO NOT use the stand for any purpose, other than that for which it is designed.
DO NOT use the stand if any parts are damaged or missing as this may cause failure and/or personal injury.
Keep children and unauthorized persons away from the work area.
Keep the stand clean for the best and safest performance and when not in use, store it in a safe, dry, childproof location.

INTRODUCTION

Ideal for holding small vehicle body parts such as grilles, spoilers, wings, and mirror housings during preparation and spraying.

SPECIFICATION

Model No:……………………………………………… MK61.V2
Height ……………………………………………………. 1105mm
Width……………………………………………………….. 850mm

ASSEMBLY

Check the contents against Fig. 1 and the parts list to confirm that all are present, and to familiarise yourself with the parts.
Mount base tubes (short) (1) onto the bottom cross tube (6), using screws (5), washers (2), and nuts (3) to tighten.
Put knob (7) into base tube ready to receive upright (8), insert upright, and tighten knob (7).
Fit top cross tube (11) and secure with a knob (7).
Fit set plates (10) onto the ends of the top cross tube (11) secure with knobs (7) and fit plugs (9) on each end.
Fit the four adjusting screws (4) into the bottom of the base tubes (1) and adjust them until the stand is level.

SEALEY-MK61.V2-Spray-Booth-Stand-fig-2

OPERATION

Loosen the knobs and adjust the position of the cross tube and set plates as required.
If required, secure the help of a second person, and lift the vehicle panel into position, find a suitable feature to rest it on.
If further security is required, use chains or similar to attach to a suitable feature on the panel and stretch the chain to the set plates.
DO NOT let go of the panel until you are sure that it is properly secured.
Retighten the knobs to lock them.
Check that the panel is stable before moving the stand.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

REGISTER YOUR PURCHASE HERE

Note:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.

Important:
No Liability is accepted for incorrect use of this product.