SENCOR SEP 560 BT Wireless Earpods User Manual
- June 16, 2024
- SENCOR
Table of Contents
SENCOR SEP 560 BT Wireless Earpods
Supply content
- “L.:’ and “R” earphone
- Charging case
- User’s manual
- USB-C charging cable
SEP 560 BT Bluetooth earphones description
- Charging case
- Left earphone LED indicator
- Charging box LED indicator
- Right earphone LED indicator
- USB-C charging connector
- Touch pad for earphones control
- Microphone
- Earphone contacts for recharging from the charging case
- Right earphone storage space,right earphone
- Left earphone storage space, left earphone
Left and right earphone function
- Touch pad for earphones control
- 2 x short touch during an incoming call – answer the call
- 1 x long touch (3 seconds) during an incoming call – call rejection
- 2 x short touch during an ongoing call – end call
- 2 x short touch – play function
- 2 x short touch – pause function
- 1 x long touch – launch SIRI/Google assistant
- 4 x short touch – change GAME/ MUSIC mode
Left earphone
- 1 x short touch in music mode – volume down
- 3 x short touch – previous track
Right earphone
- 1 x short touch in music mode – volume up
- 3 x short touch – next track
Putting into operation
Before first use, be sure to read the safety instructions contained in this
user’s manual carefully.
Before using for the first time, remove the protective film of the charging
contacts on the bottom of the earphones and return them to the charging case.
Start charging the charging case and the earphones to the maximum level.
Opening and closing the case – The case is opened and closed by sliding the
top lid from the front side to the back side as shown in the main picture.
Turning on the earphones – Taking the earphones out of the case will
automatically switch them on. When the earphones are in the off state outside
the charging case. Press and hold the touch pad on each earphone and wait for
the earphones to switch on.
Turning off the earphones – Inserting the earphones into the charging case
will automatically turn off the earphones. Long press and hold the touch pad
of the earphones until the earphones turn off.
Pairing the earphones with each other – The earphones are already paired from
the factory and do not need to be paired with each other.
(If pairing to TWS mode fails, return the earphones to the charging case and
repeat the above instructions).
Warning: To prevent damage to your hearing, always keep the volume level of
your device to a minimum before connecting BT headphones to your mobile
device. Keep the touch pad clean and avoid touching other objects or body
parts such as hair.
Note: If the BT earphones are not paired with any device, they will turn off
when left idle for a long time. Put them in the case.
Pairing your earphones via Bluetooth
To pair the BT headphones with your mobile device, do the following:
Remove the earphones from the charging case and search for the Bluetooth
earphones name “SEP 560BT” on the device you want to pair and start the
pairing process. If you are requested to enter a pairing code while your
device and the BT headphones are pairing, use the following code: “0000”
To cancel the pairing process, disconnect the BT earphones from your mobile
device (cancel the Bluetooth pairing).
Note: To ensure a stable Bluetooth connection, make sure that the distance
between the BT headphones and your paired device is kept within 10 meters.
Depending on ambient interference, in some cases it may be necessary to
maintain a shorter distance between the BT headphones and the paired device.
Charglng
A charged battery provides power for several hours of operation at normal
volume levels. A high volume consumes more battery power; I therefore, we
recommend listening at normal volume levels.
When the BT earphones are placed in the charging case, the case LEDs show the
charging status of the BT earphones and the charging case:
a. The LED indicator of left “2” and right “4” earphone is lit – the
earphones are charging
b. The LED indicator of the left “2” and right “4” earphone is lit, the
LED indicator of the charging case “3” is green – one of the earphones is
charging.
c. Left “2” and right “4” LED indicator is not lit – earphones are
charged
d. Charging case LED indicator “3” is red – the case is charging
e. Charging case LED indicator “2” flashes red – the charging case is
discharged
I. Charging case LED indicator “2” is green – the charging case is
charged
Attention: For charging, use only the original accessories supplied with
the appliance. To achieve maximum battery life, it is advisable to start
charging the battery only when the battery is low (10% – 20%).
Charge continuously until fully charged. If the battery life is already very
short, it is exhausted and we recommend you contact an authorised service
centre for more information.
Recommendation: If your headphones are not to be used for an extended
period of time, we recommend to fully charge the batteries once every two to
three months. We recommend to store the BT earphones and the charging case
with the battery charged to prevent irreparable damage to the battery (loss of
capacity).
Specification:
- Bluetooth Version 5.3
- Maximum Transmitter Power 100mW@ 2.4GHz-2.4835GHz
- Codes: SBC, MC
Safety Notice:
Please observe the rules of the Country or Region which you are in while
driving.
Do not disassemble or modify the headset at any reason, otherwise, It may
damage or burn the headset.
II there is any quality problem, please send headset to authorized service
center for repairing.
Please keep the equipment along with all the accessories out of the reach of
child ren and pets.
Extreme temperatures will cause the device deformation, reduce the charging
capacity and shorten the working life.
Please do not immerse the earphone into water. Guarantee will be lost ii
damage is caused by immersed into water.
It will damage your hearing ii you listen with high volume for a long time.
It is recommended that only use the lowest volume which is necessary for
speaking and listening to music.
Instructions and intonation regarding the disposal of used packaging
materials
Dispose of packaging material at a public waste disposal site.
Disposal of used electrical and electronic appliances
The meaning of the symbol on the product, its accessory or packaging
indicates that this product shall not be treated as household waste. Please,
dispose of this product at your applicable collection point for the recycling
of electrical & electronic equipment waste. Alternatively in some states of
the European Union or other European states you may return your products to
your local retailer when buying an equivalent new product. The correct
disposal of this product will help save valuable natural resources and help in
preventing the potential negative im pact on the environment and human health,
which could be caused as a result of improper liqu idation of waste. Please
ask your local authorities or the nearest waste collection centre for further
details. The improper disposal of this type of waste may fall subject to
national regu lations for fines.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the
necessary information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information
about the correct disposal method from local government departments or from
your seller.
This appliance complies with EU rules and regulations regarding
electromagnetic and electrical safety. Changes to the text, design and
technical specifications may occur without prior notice and we reserve the
right to make these changes.
Hereby, FAST CR, a.s. declares that the radio equipment type SEP 560 BT is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.sencor.eu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>