GE APPLIANCES GFW148SSMWW ENERGY STAR Front Load Washer with Steam User Manual
- June 16, 2024
- GE Appliances
Table of Contents
GE APPLIANCES GFW148SSMWW ENERGY STAR Front Load Washer with Steam
Product Information
The GFW148SSMWW is a front load washer designed for residential use. It has the following specifications:
- Dimensions: 42-13/16 inches (height) x 23-7/16 inches (width) x 25-5/8 inches (depth)
- Weight: Not specified
- Model Number: GFW148SSMWW
- Special Installation Requirements: ADA Compliance, Stacked Installation, Alcove or Closet Installation
ADA Compliance
The washer can be made ADA compliant by using a 4-inch ADA riser and drip pan
(part number GAF140SSNWW) for the 24 Front Load model.
Stacked Installation
If you want to stack a dryer over the washer, please note that the stacking
kit is not included with the washer. You will need to order part number
GFA24KITL separately.
Alcove or Closet Installation
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
For stacked installations, the dimensions are as follows:
- Height: 23-7/16 inches
- Width: 25-5/8 inches
- Depth: 3-3/8 inches
The dryer must be exhausted to the outside, except for the condensing dryer. Minimum clearances between the dryer cabinet and adjacent walls or surfaces are: 1 inch on the left and right sides,1 inch on the top, and 1 inch on the front and rear.
For closet installations, the closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 square inches of open area equally distributed. If the closet contains both a washer and a dryer, the doors must contain a minimum of 120 square inches of open area equally distributed. No other fuel-burning appliance should be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation
If you are installing the dryer in a bathroom or bedroom, it must be
exhausted to the outdoors, except for the condensing dryer.
The installation must conform with local codes. In the absence of local codes, it must conform with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum clearances to combustible surfaces for installations other than alcove or closet installations are: 0 inches on both sides and 3 inches at the rear.
Venting Kits and Accessories
For more information on venting kits and accessories, please call 1-800-GE-
CARES.
Product Usage Instructions
To use the GFW148SSMWW front load washer, please follow these steps:
Step 1: Loading the Washer
Open the washer door and load your laundry into the drum. Make sure not to
overload the washer as it may affect performance and cleaning results. Close
the door securely.
Step 2: Selecting a Wash Cycle
Turn the cycle selector knob to choose the desired wash cycle.
The available wash cycles may include Normal, Delicates, Heavy Duty, Quick
Wash, and more. Refer to the user manual for detailed descriptions of each
cycle.
Step 3: Adjusting Settings
If desired, you can adjust additional settings such as water temperature, spin
speed, and soil level using the control panel or buttons provided. Refer to
the user manual for instructions on adjusting specific settings.
Step 4: Starting the Wash
Press the Start/Pause button to begin the wash cycle. The washer will
automatically fill with water and start agitating. The remaining time for the
cycle will be displayed on the control panel.
Step 5: Adding Detergent
If necessary, add the appropriate amount of detergent to the detergent
dispenser. Follow the detergent manufacturer’s instructions for the correct
dosage. Close the detergent dispenser after adding detergent.
Step 6: Monitoring the Wash
During the wash cycle, you can monitor the progress through the control panel
or by observing the washer’s operation. If desired, you can pause the cycle
using the Start/Pause button and make any necessary adjustments.
Step 7: Removing the Laundry
Once the wash cycle is complete, the washer will automatically stop. Open the
door and remove your laundry. Ensure that no items are left inside the drum.
Step 8: Cleaning and Maintenance
After each use, it is recommended to clean the detergent dispenser, drum, and
door seal to prevent buildup of residue or mold. Refer to the user manual for
specific cleaning instructions.
FAQ
Q: Can I stack a dryer over this washer?
A: Yes, you can stack a dryer over this washer using a stacking kit.
However, please note that the stacking kit is not included with the washer.
You will need to order it separately (part number GFA24KITL).
Q: Can I install the dryer in a closet?
A: Yes, you can install the dryer in a closet. However, please ensure
that the closet doors are louvered or otherwise ventilated and contain the
minimum required open area. If the closet contains
both a washer and a dryer, the doors must contain a larger open area.
Q: What are the minimum clearances required for installation?
A: The minimum clearances between the washer and adjacent walls or
surfaces are 1 inch on the left and right sides, 1 inch on the top, and 1 inch
on the front and rear. For installations other than alcove or closet
installations, the minimum clearance to combustible surfaces is 0 inches on
both sides and 3 inches at the rear.
GFW148SSMWW
GE® 2.4 DOE Cu. Ft. ENERGY STAR® Front Load Washer with Steam
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
INSTALLATION INFORMATION
For complete information,see installation instructions packed with your washer.
SPECIAL INSTALLATION REQUIREMENTS
ADA COMPLIANCE:
- 4″ ADA riser and drip pan for 24″ Front Load model: GAF140SSNWW
STACKED INSTALLATION:
- Kit for stacking dryer over washer is not included with the washer.
Order part no. GFA24KITL
ALCOVE OR CLOSET INSTALLATION:
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
The dryer MUST be exhausted to the outside with the exception of the
condensing dryer.
Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 1″ left and right sides, 1″ top, 1″ front and rear.
Minimum clearances between washer cabinet and adjacent walls or other surfaces
are: 1″ left and right sides, 1″ top, 1″ front and rear.
Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet
contains both a washer and a dryer, doors must contain a minimum of 120 sq.
in. of open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a
gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
The dryer MUST be exhausted to the outdoors with the exception of the
condensing dryer.
The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS:
- Minimum clearances to combustible surfaces 0″ both sides, 3″ rear.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,PLEASE CALL 1-800-GE- CARES.
FEATURES AND BENEFITS
- Plugs into Dryer or Wall – Washer plugs into GE Condenser dryer or properly installed 120-Volt wall receptacle for easy installation
- Stainless steel basket – Long-lasting stainless steel finish resists rust and won’t chip, peel or snag clothes
- Steam – Penetrates deep into fabric fibers, loosening stains like tomato and grass, yet protects your fabrics
- ENERGY STAR® qualified – Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings
- Electronic touch controls – Enjoy easy operation and cleanability with streamlined controls 14 wash cycles – Multiple cycles are designed to specifically handle various fabrics and soils 1400 RPM spin speed – Fast spin speeds remove water efficiently and minimize dry time
Inlet fill hoses included
- Quick Wash – Provides a quick wash for lightly soiled items that are needed in a hurry
- Internal water heater – Increases wash temperature to reduce bacteria and provide better cleaning for the really tough stains
- Model GFW148SSMWW – White on white
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.