NANOFLOW V3 Evolution Board Instruction Manual
- June 16, 2024
- NANOFLOW
Table of Contents
NANOFLOW V3 Evolution Board
Specifications
- Rating: IP67/68
Product Information
The product is designed with an IP67/68 rating, indicating its resistance to dust and water. It provides a reliable and durable connection for various components.
Product Usage Instructions
Touch-Up Connector
Using a pipette, apply a few drops of V3 solution on the heads of the male
end of connections/plugs that will be directly connected to the treated
component. Ensure that the cables are fully saturated with the V3 solution.
Touch-Up Connection Area
Heat cure the component for 1 minute. Once the cables have dried, plug in
or connect the cables into the coated connection points of the component. Add
a few drops using a pipette to the surrounding attached areas.
Heat to Cure
Heat cure the component for 1 minute each or 2-5 minutes in a heat curing
oven. Let the device cool to room temperature.
Note : Please follow each process step-by-step for optimal results.
First Aid Measures
In case of any injuries or accidents related to the use or misuse of our
products, seek immediate medical attention and follow appropriate first aid
measures.
Disclaimer
- In no event shall Nanoflowx be liable for any direct, indirect, punitive, incidental, special, or consequential damages to property or life arising out of or connected with the use or misuse of our products.
- Our products and all components are provided “as is,” with all faults. Nanoflowx makes no warranties regarding our products, express or implied, including but not limited to the implied warranties of merchantability, fitness for any particular purpose, and any statutory warranty of non-infringement, other than that our products will meet or exceed their specifications.
FAQ
How can I contact Nanoflowx for questions or issues?
You can contact us via chat, phone, or email:
-
* Phone: [323-396-9200](https://phone.gd/phone/323-396-9200)- Email: info@nanoflowx.com
- Website: nanoflowx.com
SURFACE PREPARATION INSTRUCTIONS
-
SAFETY
WEAR NITRILE GLOVES AND GOGGLES BEFORE HANDLING COMPONENTS AND SOLUTION. -
POWER OFF DEVICE
ENSURE THE DEVICE IS UNPLUGGED AND FULLY POWERED DOWN FOR AT LEAST 5 MINUTES.
DISMANTLE AND REMOVE ELECTRICAL COMPONENTS TO BE TREATED FROM DEVICE IF POSSIBLE. -
HAVE A CLEAN DEVICE
CLEAN ELECTRICAL COMPONENTS WITH 91% ISOPROPYL (RUBBING ALCOHOL) TO REMOVE DUST AND OILS.
WE RECOMMEND USING A SOFT BRISTLE TOOTHBRUSH AND/OR A LINT FREE MICROFIBER. ALLOW DEVICE TO DRY.
IMPORTANT
DO NOT SUBMERGE OR APPLY SOLUTION TO LCD SCREENS.
DIRTY COMPONENTS WILL PREVENT THE COATING FROM ADHERING TO THE SURFACE, RESULTING IN A INEFFECTIVE COATING.
NANOCOATING APPLICATION INSTRUCTIONS
-
FIND A CLEAN DIP TRAY
USE A CLEAN GLASS CONTAINER THAT WILL ALLOW THE COMPONENT TO SUBMERGE IN THE SOLUTION. -
DIP DEVICE IN SOLUTION
PLACE ELECTRONIC COMPONENT IN THE GLASS CONTAINER, SLOWLY POUR THE SOLUTION COMPLETELY SUBMERGING THE COMPONENT FOR 5 SECONDS. -
DRAIN EXCESS SOLUTION
REMOVE COMPONENT HANDLING BY IT’S SIDES ONLY IN A 45 DEGREE ANGLE. CONNECTORS DOWNWARDS. ALLOW EXCESS SOLUTION TO DRAIN FOR 5 SECONDS. -
AIR OR HEAT CURE COATING
PLACE THE DEVICE ON A SAFE AREA AND ALLOW TO AIR CURE FOR 24 HOURS OR HEAT AT 176 F (B0 C) FOR 15 MINUTES WITH CURING OVEN, HEAT TUNNEL, OR HEAT GUN BOTH SIDES. THEN AIR CURE FOR 8 HOURS. DO NOT EXPOSE TO LIQUID DURING THE CURE TIME.
NOTE : UNUSED SOLUTION IN THE TRAY SHOULD BE RESEALED INTO THE ORIGINAL BOTTLE OR IN A AIR TIGHT CONTAINER TO PREVENT SOLUTION EVAPORATION.
STORAGE AND HANDLING
- REMAINING SOLUTION IN GLASS CONTAINER SHOULD BE POURED THROUGH A STRAINER FILTER (10TTTO MICRON) AND FUNNEL BACK INTO THE ORIGINAL BOTTLE FOR FUTURE USE.
- ENSURE CAP IS SECURED TIGHTLY AND STORE SOLUTION AT ROOM TEMPERATURE IN A COOL, DRY ENVIRONMENT, AND AWAY FROM DIRECT SUNLIGHT.
FOR IP67/68 RATING
WE RECOMMEND DIPPING CONNECTING CABLES TO ENSURE TWO COMPONENTS ARE COATED AND
NOT JUST HALF OF A DEVICE. DIP, HEAT, CURE AND THEN CONNECT. OPTION 2 IS TO
INSERT THE CONNECTOR AND THEN ADD A TOUCH OF SOLUTION ON TOP OF THE CONNECTOR
TO SEAL THE CONNECTOR AREA
TOUCH UP INSTRUCTIONS
-
TOUCH UP CONNECTOR
USE A PIPETTE TO PUT DROPS ON THE HEADS OF MALE END OF CONNECTIONS/PLUGS THAT WILL BE DIRECTLY CONNECTED INTO THE TREATED COMPONENT. ENSURE THE CABLES ARE FULLY SATURATED WITH V3 SOLUTION AND HEAT CURE THE COMPONENT FOR 1 MINUTE. -
TOUCH UP CONNECTION AREA
ONCE THE CABLES HAVE DRIED, PLUG IN OR CONNECT THE CABLES INTO THE COATED COMPONENT AND ADD A FEW DROPS USING A PIPETTE TO THE SURROUNDING ATTACHED AREAS. -
HEAT TO CURE USE A HEAT
GUN AT 176°F (80°C) TO HEAT THE CONNECTION POINTS FOR 1 MINUTE ON EACH SIDE OR 2-5 MINUTES IN A HEAT CURING OVEN. LET THE DEVICE COOL TO ROOM TEMPERATURE. TOUCH UP COMPLETE.
SCAN FOR VIDEO INSTRUCTIONS
FOLLOW EACH PROCESS STEP BY STEP. SIMPLY SCAN THE QR TO LEARN MORE ON OUR
APPLICATION VIDEO.
FIRST AID MEASURES
- SKIN CONTACT: IMMEDIATELY FLUSH THE CONTAMINATED CLOTHING AND FLUSH SKIN WITH WATER AND SOAP. IF SIGNS/SYMPTOMS DEVELOP, SEEK MEDICAL ATTENTION.
- EYE CONTACT: IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES AND THEN SEEK MEDICAL HELP. SEEK MEDICAL ATTENTION IF IRRITATION PERSISTS.
- INHALATION: FOR MASSIVE INHALATION. IMMEDIATELY TRANSFER THE PATIENT TO AN AREA WITH FRESH AIR. IF THE PATIENT STOPS BREATHING, PLEASE PROVIDE ARTIFICIAL RESPIRATION. IF BREATHING IS DIFFICULT, PROVIDE OXYGEN AND SEEK MEDICAL HELP.
- INGESTION: IMMEDIATELY OBTAIN MEDICAL ATTENTION. DO NOT INDUCE VOMITING.
DISCLAIMER
IN NO EVENT SHALL NANOFLOWX BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE,
INCIDENTAL, SPECIAL CONSEQUENTIAL
DAMAGES, TO PROPERTY OR LIFE, WHATSOEVER ARISING OUT OF OR CONNECTED WITH THE
USE OR MISUSE OF OUR PRODUCTS.
OUR PRODUCTS AND ALL COMPONENTS ARE PROVIDED AS IS, WITH ALL FAULTS. NANOFLOWX
MAKES NO WARRANTIES REGARDING OUR PRODUCTS, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, ITS FITNESS FOR ANY
PARTICULAR PURPOSE AND ANY STATUTORY WARRANTY OF NON-INFRINGEMENT, OTHER THAN
THAT OUR PRODUCTS WILL MEET OR EXCEED ITS SPECIFICATIONS.
HAVE QUESTIONS OR ISSUES?
CONTACT US VIA CHAT, PHONE, OR EMAIL
S 323-396-9200
info@nanoflowx.com
nanoflowx.com