KOHLER 32256-SC02-BLL Two Light Wall Sconce Installation Guide

June 16, 2024
Kohler

KOHLER-'logo

KOHLER 32256-SC02-BLL Two Light Wall Sconce

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-product

Product Information

Specifications

  • Model Number: 1554279-2-A
  • Manufacturer: Kohler Co.
  • Usage: Indoor
  • Bulb Rating: Up to 60W

FAQ

  • Q: Can this fixture be used outdoors?
    • No, this fixture is for indoor use only.
  • Q: What is the maximum bulb wattage allowed?
    • The fixture has been rated for bulbs up to 60W. Do not exceed this rating.
  • Q: Do I need to hire a qualified electrician for installation?
    • It is recommended to have the fixture installed by a qualified electrician.

Information

Thank You for Choosing KOHLER

Need help? Contact our Customer Care Center.

Warranty

  • This product is covered under the KOHLER® Indoor Lighting Fixtures Limited Warranty, found at kohler.com/warranty.
  • For a hard copy of warranty terms, contact the Customer Care Center.

Tools and Materials

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-fig-1

Plus:

  • E12 Base B11 or T8 Bulb(s) (Max 60 W)

Before You Begin

DANGER: Risk of electric shock. To avoid electrical shock, the electricity must be turned OFF at the circuit breaker or fuse box before beginning installation.
DANGER: Risk of electric shock. To avoid electrical shock, the electrical outlet box must be properly grounded.
CAUTION: Risk of property damage. To avoid risk of fire, this fixture has been rated for bulbs up to 60 W. Do not exceed this rating.

  • Follow all local plumbing, building, and electrical codes.
  • Please read all instructions before you begin.
  • The fixture should be installed by a qualified electrician.
  • This fixture is for indoor use only.
  • Carefully inspect the fixture for damage.
  • Your product may appear different from the one illustrated. The installation procedure is the same.

Installation And Connection

Install the Mounting Plate

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-fig-2

  • Carefully pull out the wiring from the electrical outlet box and allow the wires to hang down.
  • Place the flat side of the mounting plate flat against the electrical outlet box.
  • Align the mounting holes on the mounting plate with the holes on the electrical outlet box.
  • Securely tighten the mounting plate to the electrical outlet box with the mounting screws

Connect the Electrical Wires

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-fig-3

  • Make a loop in the ground wire and wrap around the grounding screw on the mounting plate. Tighten the grounding screw.
  • Attach the ground wire (green), from the quick connector, to the ground wire (usually bare copper or green) from the electrical outlet box.
  • Fasten the ground wires together with the provided wire nut.
  • Attach the neutral wire (white), from the quick connector, to the neutral wire (usually white) in the electrical outlet box.
  • Fasten the neutral wires together with the provided wire nut.
  • Attach the hot wire (black), from the quick connector, to the hot wire (usually black) in the electrical outlet box.
  • Fasten the hot wires together with the provided wire nut.
  • Wrap the wire nuts with electrical tape.
  • Verify that all plastic wire nuts are securely fastened and strands of bare wire are not exposed.

Install the Fixture

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-fig-4

NOTE: Your product may appear different than the one illustrated. The installation procedure is the same.

  • Carefully position the wires inside the electrical outlet box behind the mounting plate.
  • Connect the quick connector to the fixture.
  • Position the fixture over the mounting plate and align the screw holes.
  • Secure the fixture to the mounting plate with the provided screws.

Install the Shade(s)

KOHLER-32256-SC02-BLL-Two-Light-Wall-Sconce-fig-5

  • Remove the socket ring and sleeve from the socket.
  • Position the shade onto the socket base.
  • Reinstall the sleeve and ring over the socket.
  • Tighten the socket ring with the provided socket tool.
  • Insert the bulb(s) into the socket(s).
  • Turn ON the main electrical supply from the main fuse or circuit breaker.
  • Confirm proper operation.

Contact

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals