Tenda K4P-4TR PoE HD Video Security Kit Installation Guide
- June 16, 2024
- Tenda
Table of Contents
Quick Installation Guide
PoE HD Video Security Kit
KAP-4TR/K8P-4TR/KAP-4CR/K8P-4CR
Package contents
The PoE HD Video Security Kit with 4 Cameras is taken as an example here. The actual product prevails.
Appearance
NVR (The N6P-4H is taken as an example here.)
| Ports | Description |
|---|---|
| Grounding terminal. |
Connect the grounding terminal of the NVR to the earth or the ground terminal
of the building with a grounding cable to prevent static electricity or
lightning from damaging the NVR.
POWER| Power port. Use the included power adapter to power on the NVR.
PoEPORTS| Fast Ethernet port, which supports IEEE 802.3af /at PoE power
supply. Used to connect to cameras.
Tips
— Recommended Ethernet cable: CAT 5 or better.
— Power supply distance:
• Normal Mode (default): Up to 100m
• Long-range Mode: Up to 250m
LAN| Fast Ethernet LAN port. Used to connect to such devices as the router and
switch.
AUDIO IN| Audio input port. Used to connect to the audio input devices, such
as pickups.
UDIO OUT| Audio output port. Used to connect to audio output devices, such as
active speakers.
HDMI| HDMlport.
Connect your monitor or TV to this port using an HDMI cable for audio and
video output.
VGA| VGA port. Connect your monitor to this port using a VGA cable for video
output.
USB| USB 2.0 port. Used to connect to such devices as a mouse and a USB
storage device.
Camera
| Item | Description |
|---|---|
| 1 | Direction arrow. |
When the arrow is at 12 o’clock position, the monitoring direction is the
positive direction.
2| Microphone.
3| Ethernet port, 10/100 Mbps auto-negotiation.
The camera supports the IEEE 802.3af standard, this port can be connected to
the
PoE port of a PoE power sourcing equipment for power supply.
4| Screw hole for pendant mounting.
5| Screw hole for wall mounting
(I) Install the HDD
Tips
When installing or replacing the HDD, please cut off the power supply of the
NVR first; otherwise, the HDD may not be detected or even be damaged.
-
Use a screwdriver to unfasten the screws, then remove the cover of the NVR. Reserve the screws for later use.
-
Take out 2 screws from the NVR installation package, and screw them into the two screw holes closest to the SATA connector. Reserve about 2 mm between the screw head and the HOD for subsequent installation.
-
Align the SATA connector of the HOD with the SATA slot on the motherboard of the NVR, and then insert the HDD into the slot until it is tightly fixed.
-
Take out the remaining screws from the NVR installation package, and screw them into the HDD screw holes to fix the HOD.
-
Mount the cover with the previously removed screws.
(II) Install the camera
Tips
- Please make sure the wall or the ceiling is strong enough to withstand three times the weight of the camera.
- You may need to prepare a hammer drill, a drill bit, a rubber hammer, a screwdriver, and a ladder for the installation.
Turret camera
Remove the base
Rotate the body of the camera, align the housing slot with any base notch, and
then use a screwdriver to pry the housing at the slot to remove the base.
Fix the camera
The camera supports ceiling and wall mounting. The ceiling mounting is taken
as an example here.
Bullet camera
Fix the camera
The camera supports wall and pendant mounting. The mounting bracket of wall
mounting is included in the package. If you want to install the camera by
pendant mounting, please purchase the bracket by yourself.
The wall mounting is taken as an example here.
-
Unfasten the horizontal adjustment screw on the bottom, rotate the swing bracket to a suitable angle, and then fasten the screw.
-
Fix the camera (Running the cable through the wall is taken as an example)
Install the waterproof kit
Install the waterproof kit and wrap the end with waterproof tape for the
Ethernet port as required.
Tips
The included waterproof kit is not suitable for the Ethernet cable with
protection cover on the crystal head. See the example on the right.
Please follow the steps below to install the waterproof kit when the Ethernet port of the camera is connected to an Ethernet cable.
- Put the O-ring on the Ethernet port of the camera.
- Pass the Ethernet cable through the fixed nut, the waterproof ring and the waterproof jacket in sequence.
- Rotate to fix the waterproof jacket to the Ethernet port of the camera, insert the waterproof ring into the waterproof jacket and fasten the fixed nut.
(II) Connect the device
The K4P-4TR kit is taken as an example here.
For more configuration details, please scan the QR code of the Get Support and
Services in this guide to see the quick installation guide.
(IV) Basic configuration
Local Management
Startup
Tips
Use the included power adapter to power on the NVR. Abnormal power supply will
cause the NVR to not work properly, or even the NVR may be damaged.
Connect the included power adapter to the power port of the NVR, and plug the
power adapter into the power socket to start up the NVR.
Shutdown
Tips
Do not directly cut off the power supply of the NVR to force a shutdown;
otherwise, the HDD may be damaged, videos may be lost, or even the NVR may be
damaged.
After the mouse and monitor are connected to the NVR, you can perform the
following settings on the NV R’s GUI (exit the Full Screen interface):
Click in the upper right corner, click Shutdown , and then click OK. When “The
Device is Shut Down.
Please Cut Off the Power” appears on the screen, unplug the power adapter of
the NVR.
Quick setup
After connecting the mouse and monitor to the NVR, you can perform quick
setup.
App Management
After the cloud service of the NVR is enabled and the cloud status is Online,
you can add and manage the NVR through the TDSEE App.
-
Download the TDSEE App.
After the mobile phone is connected to the internet successfully, download and install the TDSEE App onto your mobile phone by scanning the QR code or by searching for TDSEE in Google Play or App Store.
http://download.cloud.tenda.com.cn/down/TendaSecurity -
Ensure that the NVR is powered on and working properly.
-
Run the TDSEE App and follow the instructions to complete user registration. Enter the homepage, then tap Add a device or in the upper right corner of the homepage.
Tips
To ensure that the login password of the NVR can be reset through the TDSEE App, register with the reserved email address when activating the NVR. -
Scan the QR code on the label at the bottom of the NVR or scan the QR code on the Cloud Service page, then follow the instructions in the App.
After the NVR is added, you can remotely preview real-time videos, play back the recordings and check alarm messages through the TDSEE App.
Web Management
These series of NVRs can be managed on the web UI.
Activate
If the NVR is not activated, you can activate it through the web UI. When the
activation is completed, you need to log in again.
-
Connect the computer to the switch or router that is connected to the NVR.
-
Set the IP address of the computer to an unused one belonging to the same network segment as the IP address of the NVR but different from the IP address of the NVR.
The default login IP address of the NVR is 192.168.1.254, please set the IP address of the computer to 192.168.1.X 0X indicates 2 to 253, and is unused by other devices). -
Launch a browser and enter the default IP address 192.168.1.254 of the NVR in the address bar. Set Password, enter your Email Address, and click Activate.
Tips
The NVR supports HTTPS login. When you access its web UI, the browser may
prompt that the web address is not secure, just ignore it and continue.
Done. You can re-enter the web UI of the NVR to preview real-time videos or
configure the NVR as required.
The DHCP function of the NVR is enabled. If there is a DHCP server in the
network, the IP address of the NVR may be changed. Please refer to the actual
IP address assigned to the NVR by the DHCP server.
Log in to web UI
Refer to step 1 to 3 in Activate to operate.
is displayed in the upper right corner of the channel. If no recording icon is displayed in the upper right corner of the channel, try the following solutions: – If the HOD is not installed inside the NVR, please install it first. – Navigate to Configuration> Storage> HDD to check whether the HOD is normal. If the status of the HDD is abnormal, please shut down the NVR first, then remove the cover and unplug and re-plug the HOD. If the problem persists, please format or replace the HOD. — Navigate to Configuration > Storage > Schedule to check that the recording function is enabled, and the recording mode and time are set correctly. If a recording icon is displayed In the upper right corner of the channel, please try the following solutions: – Navigate to Configuration > System > Time to ensure that the system time of the NVR is accurate. – Navigate to Configuration > Storage > HOD to check whether the HOD space is full. By default, the Overwrite function is enabled. If the HDD space is full, the oldest recording files will be overwritten. ” image-2=”” headline-3=”p” question-3=”Q3. What should I do if the TDSEE App fails to add the NVR?” answer-3=”A3. Try the following solutions: Navigate to Configuration
Network > Cloud Service of the NVR to ensure that the cloud service function is enabled. — If Cloud Status is Online, please ensure that the mobile phone (with the App installed) is connected to the internet. – If Cloud Status is Offline, try the following solutions: • Navigate to Configuration> Network> Internet to ensure that the internet parameters configuration is correct. • Ensure that the LAN port of the NVR is correctly connected to the peer side (switch or router• Ensure that the router in the network is connected to the internet and the filter function is ena(such as MAC filter and blacklist). • Ensure that the DHCP server function of the router in the network is enabled. ” image-3=”” headline-4=”h2″ question-4=”” answer-4=”” image-4=”” count=”5″ html=”true” css_class=””]
Get Support and Services
For technical specifications, user guides and more information, please visit
the product page or service page on www.tendacn.com.
Multiple languages are available.
You can see the product name and model on the product label.
https://www.tendacn.com/service/default.html
Safety Precautions
Before performing an operation, read the operation instructions and
precautions to be taken, and follow them to prevent accidents. The warning and
danger items in other documents do not cover all the safety precautions that
must be followed. They are only supplementary information, and the
installation and maintenance personnel need to understand the basic safety
precautions to be taken.
-
The NVR is only suitable for mounting at heights s 2m; The camera is suitable for mounting at heights >2m
-
For desktop mounting, the NVR must be horizontally mounted for safe use.
-
PoE power supply does not meet the LPS, connect the power supply products must meet the fire shell requirements.
-
Please use the included power adapter.
-
Mains plug is used as the disconnect device, and shall remain readily operable.
-
The power socket shall be installed near the device and easily accessible.
-
Operating temperature:
Power adapter: 0C – 40°C.
N6P-4H & N6P-8H: 0C -40C.
IC7: -10C-50C.
IT7: -20°C – 60°C. -
Keep the device away from water, fire, high electric field, high magnetic field, and inflammable and explosive items.
-
Do not use the power adapter if its plug or cord is damaged.
-
If such phenomena as smoke, abnormal sound or smell appear when you use the device, immediately stop using it and disconnect its power supply, unplug all connected cables, and contact the after-sales service personnel.
-
Disassembling or modifying the device or its accessories without authorization voids the warranty, and might cause safety hazards.
For latest safety precautions, see Safety and Regulatory Information on www.tendacn.com.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. (2) To avoid
unnecessary radiation interference, it is recommended to use a shielded RJ45
cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the device is in
compliance with Directive 2014/35/EU and 2014/30/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://www.tendacn.com/download/list-9.html
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the
environment.
User has the choice to give his product to a competent recycling organization
or to the retailer when he buys a new electrical or electronic equipment.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
Floor 6-8, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen,
China. 518052
Website: www.tendacn.com
E-mail: tendasecurity@tenda.cn
support.us@tenda.cn (North America)
support.uk@tenda.cn (United Kingdom)
Copyright
© 2023 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co.,
Ltd. Other brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders.
Specifications are subject to change without notice.
V1.1 Keep for future reference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>