CRUISE CRPP-2.6 Plug and Play Speaker Set Instruction Manual
- June 4, 2024
- CRUISE
Table of Contents
CRRPP-2.6
User manual
Seat / Skoda / VW
DLS CRUISE
CRPP-2.6
CRPP-2.6 Plug and Play Speaker Set
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-2.6. For us, it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you fully
read this manual, preferably before you start your installation. Keep the
manual in a safe and accessible place for future
reference.
Your speakers must be installed correctly in order to work as intended. Make
sure you have all the necessary tools nearby before starting and that you are
completely confident in how to process. If you feel the slightest uncertainty;
feel free to take the help of an experienced installer or a car audio dealer.
Warranty
This component kit is covered by warranty, depending on the conditions in the
country where it is sold. If the speaker is returned for service, please
include the original dated
receipt with the product.
General
Some sound systems may vary in size of the door speaker. Make sure that your
vehicle has the same size as this kit, before you start the assembly
This is a generic mounting instruction. The approach is similar to all of the
described car models. Some screws and clips may be placed differently and
depending if the tweeter
is placed in the A-pillar or side mirror, the course of action may vary.
Declaration of conformity
DLS plug-and-play speakers for vehicles are manufactured in accordance with
the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with the WEEE-directive 2012/19/EC.
The products are also produced in accordance with the EU RoHS directive
2015/863/EU.
Included products:
2pcs Woofer
2pcs Tweeter
2pcs Crossover
Included in box:
2pcs Tweeter connection
4pcs Adhesive foam for wrapping
4pcs Terminal crimp connectors
2pcs Four-leaf clover foam for the tweeter
10pcs Blind rivet
1pcs Rivet Tool
1pcs Manual
Pre-installation
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure the
negative terminal from your battery/power source. This will prevent the risk
of damaging yourself or the products. Place the disconnected terminal in a
secure and isolated location away from any possible connection belonging to
the battery/power source system.
General info
Some sound systems may vary in size of the door speaker. Make sure that
your vehicle has the same size as this kit before you start the assembly This
is a generic mounting instruction. The approach is similar to all of the
described car models. Some screws and clips may be placed differently and
depending if the tweeter is placed in the A-pillar or side mirror, the course
of action may vary.
Installation
Start the dismount
Dismount the front door by removing the cover of the door panel.
Hint: Use plastic PRY tools to avoid marks on the panels and destroy the
plastic clips.
Usually, the clips/screws are placed by red marks. It may be different in your vehicle.
Be careful when removing the panels and lids, so there will be no
marks.In most cases the screws used are Torx T30.
Unscrew them and store them in a safe position, to re-use when re-mounting the
door panel.
Usually, a wrench, size 10, will be needed. Normally- ally the bolt is located
at the underside of the door. When the door panel is loose, start with softly
lifting it straight up, to remove the panel.
There are several electric and mechanical connectors on the backside of the
panel.
Release the door lock cable Disconnect the window control panel, cables for
lightning, speaker cable harness, and any other connections.
The door speakers are fixed with rivets.
Use a 4mm drill to remove the rivets. Make sure all remains from the old rivets are removed from the inside of the door.
Mounting the DLS drivers
Place the new DLS driver in the hole for the speaker. Use the included rivets
and the rivet tool to safely mount the driver.
(Step 3 might be done several times)
-
Insert rivet
-
Plug in the rivet tool
-
Press handles
-
Remove the pin
Connect the speaker harness.
Start the assembly of the door panel.
Reconnect all wires harnesses.
Connect all plugs to the door cover, reconnect the unlocking device, place the
door cover from the top, by the window seal and push it gently down.
Make sure the clips are in place and can engage. Give the door panel a push by
the hand to attach to the clips. Mount and fasten all screws to the correct
places.
Change Tweeter
Locate the tweeter – Either in the A-pillar, by the side mirror or in the same case in the door by the handle.Dismount over and remove the covers. Use Plastic PRY tools and be careful, there can be airbags behind the A-pillar. The first clip can be really hard to remove. Take it easy and use minimal force. (This shows how to unmount the A-pillar tweeter) Un-clip the speaker connector from the tweeter
Remove the old tweeter
Use a cutting nipper or a Snap-off blade knife to remove the top of the
plastic pin that holds the tweeter.
Don’t remove the whole pin, just the top!Change the tweeter, and place
it where the OEM tweeter used to be. Make sure that the DLS tweeter is
properly fixed. Remove the protecting plastic sheet from the adhesive four-
leaf clover and use it to hold the new tweeter in place. Make sure the tweeter
is fixed in a safe way.For some models, the four-leaf clover needs to be
adapted. Use a sharp scissor to modify it. Connect the crossover with the PnP
connector. Use the other adhesive foam to secure the crossover and
cablesThe yellow cables are a jumper for
decreasing the tweeter level 4dB
Finally
Start assembling the covers again to finish the work. Make sure that no screws
or clips are left over, Reconnect the battery/power source terminal.
Finally, it´s time to play some good music and enjoy!
Running-in time
Allow the component kit to play for at least 15-20 hours in order to perform
at its possible best. This run-in can be made with tone sweep or with just
music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in the session, the performance
and characteristics will be in the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold
or the distributor in your country. You can always contact the DLS Helpdesk in
Sweden at
e-mail: info@dls.se. Information can also be found on
our WEB- site www.dls.se. We follow a policy of
continuous advancement in development. For this reason, all or part of the
specifications and designs may be changed without prior notice.
Specifications
Art. no CK-CRPP-2.6
Woofer 6.5” /165 mm with glass fiber cone
Tweeter 1” / 25 mm silk dome tweeter with accessories
RMS Power 100 W
MAX Power 200W
Impedance 3 Ohm
Sensitivity 90dB 1W/1M
Freq. range 55Hz-25kHz
Crossover 4.8kHz 12dB/Oct with Mundorf caps
Attenuation Tweeter -4db/0db
DLS DRIVE CRPP-2.6 Tweeter
Technical Specification:
Size 1” /2.54 mm
RMS Power 50 W
MAX Power 100W
Voice Coil Material CCAW voice coil/ Aluminium former
Frame Glass Fiber Reinforced ABS
Magnet Neodymium/Copper shorting ring
Cone Natural silk dome
Impedance 4 ohm
Freq. range 2000Hz-25kHz
Electro-Acoustic Parameters:
Re 3.5 Ohm
Fs 1992 Hz
SPL 94 dB 1W/1M DLS DRIVE CRPP-2.6 Woofer
Technical Specification
Size | 6,5” /165 mm |
---|---|
RMS Power | 100 W |
MAX Power | 200W |
Voice Coil Size | 1” /25mm |
Voice Coil Material | CCAW voice coil/ Kapton former |
Basket | Glass Fiber Reinforced ABS |
Magnet | Ferrite |
Cone | Glass Fiber |
Suspension | Rubber |
Impedance | 3 ohm |
Freq. range | 55Hz-5kHz |
Electro-Acoustic Parameters
Re | 2.4 Ohm |
---|---|
Fs | 68.4 Hz |
MMS | 12.6 gr |
Cms | 0.427 |
Vas | 11.6L |
Qty | 0.74 |
Qes | 0.85 |
Qms | 6.3 |
Bl | 3.96 T.m |
Spl | 88.5 dB 1W/1M |
Sd | 132 cm² |
Impedance VS Frequency
DLS Cruise CRPP-2.6 compatible car models
Car | Model | Year | Front kit | Rear kit |
---|---|---|---|---|
VW | AMAROK | 2010-2021 | CRPP-2.6 | CRPP-2.6* |
VW | NEW BEETLE | 1997-2011 | CRPP-2.6 | |
VW | BORA | 1998-2005 | CRPP-2.6 | CRPP-2.6* |
VW | BORA VARIANT | 1999-2005 | CRPP-2.6 | CRPP-2.6* |
VW | C-Trec | 2016-2021 | CRPP-2.6 | CRPP-2.6* |
VW | CADDY | 2020-2021 | CRPP-2.6 | |
VW | CRAFTER II | 2017-2021 | CRPP-2.6 | |
VW | GOLF IV | 1997-2004 | CRPP-2.6 | CRPP-2.6* |
VW | GOLV VI | 2008-2014 | CRPP-2.6 | CRPP-2.6* |
VW | GOLF VII | 2012-2020 | CRPP-2.6 | CRPP-2.6* |
VW | GOLF VIII | 2020-2021 | CRPP-2.6 | CRPP-2.6* |
VW | ID 3 | 2020- | CRPP-2.6 | |
VW | ID 4 | 2021- | CRPP-2.6 | |
VW | JETTA VII | 2015-2021 | CRPP-2.6 | CRPP-2.6* |
VW | LAVIDA | 2008-2018 | CRPP-2.6 | CRPP-2.6* |
VW | LAVIDA PLUS | 2018-2021 | CRPP-2.6 | CRPP-2.6* |
VW | LUPO | 1998-2005 | CRPP-2.6 | |
VW | MOGOTAN | 2013-2016 | CRPP-2.6 | CRPP-2.6* |
VW | NIVUS | 2020-2021 | CRPP-2.6 | |
VW | PASSAT | 1996-2005 | CRPP-2.6 | |
VW | PASSAT | 2005-2015 | CRPP-2.6 | |
VW | POLO IV | 2001-2009 | CRPP-2.6 | |
VW | POLO V | 2009-2016 | CRPP-2.6 | |
VW | POLO VI | 2017-2021 | CRPP-2.6 | |
VW | NEW SANTANA | 2012-2021 | CRPP-2.6 | |
VW | SCIROCCO | 2008-2017 | CRPP-2.6 | |
VW | T-CROSS | 2019-2021 | CRPP-2.6 | |
VW | T-ROC CAB | 2020-2021 | CRPP-2.6 | |
VW | T-ROC | 2017-2021 | CRPP-2.6 | |
VW | T6.1 MULTIVAN | 2020-2021 | CRPP-2.6 | |
VW | TAREK | 2018-2021 | CRPP-2.6 | |
VW | THARU | 2018-2021 | CRPP-2.6 | |
VW | TIGUAN | 2007-2016 | CRPP-2.6 | CRPP-2.6* |
VW | TIGUAN II | 2016-2021 | CRPP-2.6 | CRPP-2.6* |
VW | UP E-UP! | 2011-2021 | CRPP-2.6 | |
VW | VENTO | 2010-2020 | CRPP-2.6 | |
SKODA | FABIA I | 1999-2007 | CRPP-2.6 | |
SKODA | FABIA II | 2007-2014 | CRPP-2.6 | CRPP-2.6* |
SKODA | FABIA III | 2015-2021 | CRPP-2.6 | CRPP-2.6* |
SKODA | OCTAVIA I | 1996-2004 | CRPP-2.6 | |
SKODA | ROOMSTER | 2006-2015 | CRPP-2.6 | CRPP-2.6* |
SKODA | YETI | 2009-2017 | CRPP-2.6 | CRPP-2.6* |
SKODA | KAMIQ | 2019-2021 | CRPP-2.6 | |
SKODA | RAPID | 2012-2021 | CRPP-2.6 | |
SEAT | ALTEA | 2004-2015 | CRPP-2.6 | |
SEAT | ALTEA XL | 2004-2015 | CRPP-2.6 | |
SEAT | ARONA | 2018-2021 | CRPP-2.6 | |
SEAT | AROSA | 1997-2004 | CRPP-2.6 | |
SEAT | CORDOBA II | 2002-2009 | CRPP-2.6 | |
SEAT | IBIZA III | 2001-2008 | CRPP-2.6 | |
SEAT | IBIZA IV | 2008-2017 | CRPP-2.6 | |
SEAT | IBIZA V | 2018-2021 | CRPP-2.6 | CRPP-2.6* |
SEAT | LEON | 2000-2005 | CRPP-2.6 | |
SEAT | LEON II | 2006-2012 | CRPP-2.6 | |
SEAT | MII | 2012-2021 | CRPP-2.6 | |
SEAT | TOLEDO II | 1994-2004 | CRPP-2.6 | |
SEAT | TOLEDO III | 2004-2009 | CRPP-2.6 | |
SEAT | TOLEDO IV | 2012-2019 | CRPP-2.6 |
*Disclaimer
DLS CRPP-2.6 is not compatible if your vehicle is with the original Premium
Hi-fi system.
The component system fits in rear doors if there is a location for a tweeter.
Product markings
The crossed-out wheelie bin symbol means that the product, literature, and
packaging included must be taken to a separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.
This product has been granted the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products comply with the relevant provisions of the RoHS Directive for the
European Union. In common with all Electrical and Electronic Equipment (EEE)
the product should not be disposed of as household waste. Alternative
arrangements may apply in other jurisdictions.
DLS is a global partner of the European Mobile Media Association, an
organization that focuses on promoting custom-made mobile media installations
to consumers.
We follow a policy of continuous advancement in development. For this reason,
all or part of specifications & designs may be changed without prior notice.
We reserve for possible typos, and factual or numeric errors that may have
been printed on any products, package designs, user manuals and/or other
included accessories.
DLS CRUISE
CRPP-2.6
DLS speakers are engineered by DLS Sweden, a part of: Winn Scandinavia AB
Elementvägen 15 – SE-702 27 Örebro – Sweden
Tel: +46 19 20 67 65 – E-mail: info@dls.se
www.dls.se
Designed & Sound tuned in Sweden.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>