DLS CRUISE CRPP-2.6CX Fanatic Audio User Manual
- June 13, 2024
- DLS CRUISE
Table of Contents
- DLS CRUISE CRPP-2.6CX Fanatic Audio
- Product Usage Instructions
- Included products
- Pre-installation
- Installation
- Remove door speaker
- Mount door speakers
- Connect the speaker harness
- Specifications
- Impedance VS Frequency
- Product markings
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DLS CRUISE CRPP-2.6CX Fanatic Audio
Product Information
Welcome to DLS! Thank you for buying a DLS Cruise CRPP-2.6CX. DLS is
committed to providing a superior sound experience and ensuring high
construction quality. To optimize your experience, it is important to fully
read this manual before installation. Keep the manual in a safe and accessible
place for future reference.
Product Usage Instructions
Installation
Dismount door panel:
- Remove the cover of the door panel. Use plastic PRY tools to avoid marks on the panels and damage to the plastic clips.
Pre-installation:
- Disconnect and secure the negative terminal from your battery/power source before replacing speakers. This prevents the risk of damaging yourself or the products. Place the disconnected terminal in a secure and isolated location away from any possible connection belonging to the battery/power source system.
General info:
- Ensure that your vehicle has the same size as the coaxial speaker (DLS CRPP-2.6CX) before starting the assembly.
- This mounting instruction is generic and applicable to all described car models. However, screws and clips placement may vary depending on your car model.
- The DLS CRPP-2.6CX can be installed instead of DLS CRPP-2.6, but the OEM tweeter will still be connected.
Note: In most cases, Torx T30 screws are used.
Unscrew them and store them in a safe place to reuse when re-mounting the door
panel. Use a wrench, size 10, to turn the bolt located at the underside of the
door by 90 degrees.
User manual
Seat / Skoda / VW
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-2.6CX. For us,it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you fully
read this manual, preferably before you start your installation. Keep the
manual in a safe and accessible place for future reference.
Your speakers must be installed correctly in order to work as intended. Make
sure you have all necessary tools nearby before starting and that you are
completely confident in how to proceed. If you feel the slightest uncertainty;
feel free to take the help of an experienced installer or a car audio dealer
Warranty
This coaxial speaker is covered by warranty, depending on the conditions in
the country where it is sold. If the speaker is returned for service, please
include the original dated receipt with the product.
Declaration of conformity
DLS plug-and-play speakers for vehicles are manufactured in accordance with
the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with the WEEE-directive 2012/19/EC.
The products are also produced in accordance with the EU RoHS directive
2015/863/EU.
Included products
- 2pcs Coaxial speakers
Included in box:
- 4pcs Adhesive foams for wrapping
- 4pcs Terminal crimp connectors
- 10pcs Blind rivets
- 1pc PRY Tool
- 1pc Manual
Pre-installation
Disconnect Battery
Before you start the process of replacing speakers,disconnect and secure the negative terminal from your battery/power source. This will prevent the risk of damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from any possible connection belonging to the battery/power source system.
General info
Some sound systems may vary in size of the door speaker. Make sure that your
vehicle has the same size as this coaxial speaker, before you start the
assembly.
This is a generic mounting instruction. The approach is similar to all of the
described car models. Some screws and clips may be placed differently and
depending on your car model.
The DLS CRPP-2.6CX can be installed instead of DLS CRPP-2.6 but the OEM
tweeter will in this case, still be connected
Installation
Dismount door panel
Dismount the door by removing the cover of the door panel.
- Hint: Use plastic PRY tools to avoid marks on the panels and destroy the plastic clips.
Usually the clips/screws are placed by the white rings. It may be different in your vehicle.
In most cases the screws used are Torx T30. Unscrew them and store them in a safe place, to re-use when re-mounting the door panel.
Use a wrench, size 10. Normally the bolt is located at the underside of the door. Turn bolt 90 degrees.
Be careful when removing the panels and lids, so there will be no marks.
When the door panel is loose, start with softly lifting it straight up, to
remove the panel.
There are several electric and mechanical connectors on the backside of the
panel. Release the door lock cable.
Disconnect the window control panel, cables for lights, speaker cable harness and any other connections.
Remove door speaker
The door speakers are fixed with rivets.
Use a 4mm drill to remove the rivets. Make sure all remains from the old rivets are removed from the inside of the door.
Just drill enough to remove the top of the rivets.
Mount door speakers
Place the new DLS driver in the hole for the speaker. DLS recommends using a rivet tool (not included in CRPP-2.6CX) and rivets to safely mount the driver. (Step 3 might be done several times)
Connect the speaker harness
Start the assembly of the door panel.
Reconnect all wires harness.
Connect all plugs to the door cover, reconnect the unlocking device, place the
door cover from the top, by the window seal and push it gently down. Make sure
the clips are in place and can engage. Give the door panel a push by the hand
to attach to the clips. Mount and fasten all screws to the correct places.
Finally
Start assembling the covers again to finish the work. Make sure that no screws
or clips are left over, reconnect the battery/power source terminal.
Finally, it’s time to play some good music and enjoy!
Running-in time
Allow the coaxial speaker to play for at least 15-20 hours in order to perform
at its possibly best. This run-in can be made with tone sweep or with just
music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in session the performance and
characteristics will be in the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your country. You can always contact the DLS Helpdesk in Sweden at e-mail: info@dls.se. Information can also be found on our WEB- site www.dls.se. We follow a policy of continuous advancement in development. For this reason, all or part of the specifications and designs may be changed without prior notice.
Specifications
Art. no CK-CRPP-2.6CX
- Woofer 6.5” / 165 mm with glass fiber cone
- Tweeter 1” / 25 mm silk dome tweeter with accessories
- RMS Power 90 W
- MAX Power 180 W
- Impedance 3 Ohm
- Sensitivity 90dB 1W / 1M
- Freq. range 65 Hz – 25 kHz
- Crossover 4.8 kHz 6dB / Oct with Mundorf caps
DLS Cruise CRPP-2.6CX Tweeter
Technical Specification:
- Size 1” / 25.4 mm
- Voice Coil Material CCAW voice coil / Aluminium former
- Frame Glass Fiber Reinforced ABS
- Magnet Neodymium / Copper shorting ring
- Cone Natural silk dome
DLS Cruise CRPP-2.6CX Woofer
Technical Specification
- Size 6.5” / 165 mm
- Voice Coil Size 1” / 25mm
- Voice Coil Material CCAW voice coil / Kapton former
- Basket Glass Fiber Reinforced ABS
- Magnet Ferrite
- Cone Glass Fiber
- Suspension Rubber
Electro-Acoustic Parameters
- Re 2.7 Ohm
- Fs 74.4 Hz
- Mms 10.7 gr
- Cms 0.426
- Vas 11.1L
- Qts 0.87
- Qes 0.97
- Qms 9.0
- Bl 3.96 T.m
- Spl 88.7 dB 1W/1M
- Sd 139 cm²
Impedance VS Frequency
DLS Cruise CRPP-2.6CX
The DLS coaxial speaker is developed to be installed in the back door of your car. However, you can install it as a front speaker in your system even if an OEM component kit is installed in your car. The tweeter level will be different due to the placement of the tweeter in the coaxial speaker and your OEM tweeter will still be connected, by default to your stereo.
DLS Cruise CRPP-2.6CX compatible car models
Car | Model | Year | Front speaker | Rear speaker |
---|---|---|---|---|
MAN | TGE | 2017-2022 | CRPP-2.6CX* | |
SEAT | ALTEA | 2004-2015 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | ALTEA XL | 2004-2015 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | ARONA | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | AROSA | 1997-2004 | CRPP-2.6CX* | |
SEAT | ATECA | 2016-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | CORDOBA II | 2002-2009 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | IBIZA III | 2001-2008 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | IBIZA IV | 2008-2017 | CRPP-2.6CX* | |
SEAT | IBIZA V | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | LEON | 2000-2005 | CRPP-2.6CX* | |
SEAT | LEON II | 2006-2012 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | MII | 2012-2021 | CRPP-2.6CX* | |
SEAT | TOLEDO II | 1994-2004 | CRPP-2.6CX* | |
SEAT | TOLEDO III | 2004-2009 | CRPP-2.6CX* | CRPP-2.6CX* |
SEAT | TOLEDO IV | 2012-2019 | CRPP-2.6CX* | |
SKODA | CITIGO | 2012-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | FABIA I | 1999-2007 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | FABIA II | 2007-2014 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | FABIA III | 2015-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | KAMIQ | 2019-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | KAROQ | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | KODIAQ | 2017-2022 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | OCTAVIA II | 2004-2013 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | OCTAVIA III | 2013-20 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | ROOMSTER | 2006-2015 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | RAPID | 2012-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | SCALA | 2019-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | SUPERB | 2008-2015 | CRPP-2.6CX* | |
SKODA | SUPERB | 2016-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | YETI | 2009-2017 | CRPP-2.6CX* | CRPP-2.6CX* |
SKODA | YETI II | 2018-2021 | CRPP-2.6CX* | |
SKODA | SUPERB | 2016-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
Car | Model | Year | Front speaker | Rear speaker |
--- | --- | --- | --- | --- |
VW | ARETON | 2017-2021 | CRPP-2.6CX* | |
VW | AMAROK | 2010-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | ATLAS | 2010-2021 | CRPP-2.6CX* | |
VW | NEW BEETLE | 1997-2011 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | BEETLE | 2011-2021 | CRPP-2.6CX* | |
VW | BORA | 1998-2005 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | BORA VARIANT | 1999-2005 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | C-Trec | 2016-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | CADDY | 2020-2021 | CRPP-2.6CX* | |
VW | CRAFTER II | 2017-2021 | CRPP-2.6CX* | |
VW | EOS | 2006-2011 | CRPP-2.6CX* | |
VW | GOLF IV | 1997-2004 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | GOLF V | 2004-2008 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | GOLV VI | 2008-2014 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | GOLF VII | 2012-2020 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | GOLF VIII | 2020-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | ID 3 | 2020- | CRPP-2.6CX* | |
VW | ID 4 | 2021- | CRPP-2.6CX* | |
VW | JETTA | 2005-2010 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | JETTA VII | 2015-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | LAVIDA | 2008-2018 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | LAVIDA PLUS | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | LUPO | 1998-2005 | CRPP-2.6CX* | |
VW | MAGOTAN | 2013-2016 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | MAGOTAN | 2017-2021 | CRPP-2.6CX* | |
VW | NIVUS | 2020-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | PASSAT | 1996-2005 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | PASSAT | 2005-2015 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | PASSAT | 2015-2021 | CRPP-2.6CX* | |
VW | POLO IV | 2001-2009 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | POLO V | 2009-2016 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | POLO VI | 2017-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | NEW SANTANA | 2012-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | SCIROCCO | 2008-2017 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | T6.1 MULTIVAN | 2020-2021 | CRPP-2.6CX* | |
VW | TAREK | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | TAYRON | 2019-2021 | CRPP-2.6CX* | |
VW | TERAMONT | 2018-2021 | CRPP-2.6CX* | |
VW | THARU | 2018-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | TIGUAN | 2007-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | TOURAN | 2003-2021 | CRPP-2.6CX* | |
VW | T-CROSS | 2019-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | T-ROC CAB | 2020-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | T-ROC | 2017-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | UP E-UP! | 2011-2021 | CRPP-2.6CX* | CRPP-2.6CX* |
VW | VENTO | 2010-2020 | CRPP-2.6CX* | CRPP-2.6CX* |
Product markings
The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.
This product has been granted with the CE certification mark to show that the product follows the health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.
DLS is a global partner of the European Mobile Media Association, an organisation that focus on promoting the custom made mobile media installations to consumers.
We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.
DLS speakers are engineered by DLS Sweden,a part of:
Winn Scandinavia AB
Elementvägen 15 – SE-702 27 Örebro – Sweden
Tel: +46 19 20 67 65 – E-mail: info@dls.se
www.dls.se
Designed & Sound tuned in Sweden.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>