CRUISE CRPP-VO1.6 Adapted Kit System for Volvo User Manual
- June 9, 2024
- CRUISE
Table of Contents
CRUISE CRPP-VO1.6 Adapted Kit System for Volvo
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-VO1.6. For us, it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you fully
read this manual, preferably before you start your installation. Keep the
manual in a safe and accessible place for future reference.
Your speakers must be installed correctly in order to work as intended. Make
sure you have all necessary tools nearby before starting and that you are
completely confident in how to proceed. If you feel the slightest uncertainty;
feel free to take the help of an experienced installer or a car audio dealer.
Warranty
This component kit is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product.
General
Some sound systems may vary in size of the door speaker. Make sure that your
vehicle has the same size as this component kit, before you start the assembly
This is a generic mounting instruction. The approach is similar to all of the
described car models. Some screws and clips may be placed differently and
depending on your car model.
Declaration of conformity
DLS plug and play speakers for vehicles are manu- factured in accordance with the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval number. They are also marked in accordance with the WEEE-directive 2012/19/EC. The products are also produced in accordance with the EU RoHS directive 2015/863/EU.
DLS speakers are engineered by DLS Sweden, a part of:
Winn Scandinavia AB
Elementvägen 15 – SE-702 27 Örebro – Sweden Tel: +46 19 20 67 65 – E-mail
: info@dls.se www.dls.se
Included products
- 2pcs Woofers
- 2pcs Tweeters
- 2pcs crossovers
Included in box:
- 2pcs 3M adhesive foams for tweeter
- 4pcs Adhesive foams for wrapping
- 4pcs Terminal crimp connectors
- 2pcs Sound optimized tweeter brackets
- 8pcs Blind rivets
- 1pc Rivet tool
- 1pc Pry tool
- 1pc Manual
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure the
negative terminal from your battery/power source. This will prevent the risk
of damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from
any possible connection belonging to the battery/power source system.
General info
- Some sound systems may vary in size of the door speaker. Make sure that your vehicle has the same size as this component kit, before you start the assembly
- This is a generic mounting instruction. The approach is similar to all of the described car models. Some screws and clips may be placed differently and depending on your car model.
Installation
Start the dismount
-
Dismount the front door by removing the cover of the door panel.
Hint: Use plastic PRY tools to avoid marks on the panels or damaging the plastic clips.
-
If your door has a corner cover, you need to remove them first and also remove the cover for the tweeter.
Corner cover is attached with 2 clips and the tweeter cover is normally attached with 2 or 3 clips. -
Remove the electric window panel and disconnect the plug on the back side of the panel. Always use plastic PRY tools when removing panels and interior, to avoid marks on the panels and leather.
Remove the door lock knob before removing the door panel. -
Depending on the car model, the amount of screws and placement can vary. In most cases the screws used are Torx T25.
-
Be careful when removing the door panels and lids. Use PRY tools.
-
Some newer models don’t have plastic clips to hold the door in place. Just remove the screws and gently press the door panel up. Be careful with the door lock knob. Just move the panel straight up.
-
There are several electric and mechanical connectors on the backside of the panel. Release the door lock cable.
-
Disconnect all cables for lightning, speaker cable harness and any other connections.
Remove woofer
- The door speakers are either fixed with rivets or screws. Make sure you have correct tools for each operation.
RIVETS
- Use a 4mm drill to remove the rivets. Make sure all remains from the old rivets are removed from the inside of the door.
- Just drill enough to remove the top of the rivets. Remember to disconnect the speaker harness before unmounting the speaker.
SCREWS
Speakers fixed with screws. Make sure to use correct tools to unscrew. Save
the screws for reattachment of the new DLS speaker.
Mounting speakers
RIVETS (Mounting new speakers)
If the speakers were fixed with rivets. DLS recommends using a rivet tool to
fix the new DLS speakers.
Place the new DLS driver in the hole for the speaker. Use the included rivet
tool and rivets to safely mount the driver. (Step 3 might be done several
times)
SCREWS (Mounting new speakers)
If the speakers were fixed with screws. DLS recommends using the OEM screws to
secure the new DLS speakers. Use the correct screw bit.
Place the new DLS driver in the hole for the speaker and use the screws to fix
the speaker.
Connect the speaker harness. Start the assembly of the door panel. Reconnect
all wires harness.
Hint : Don’t forget to connect the tweeter cable (with crossover) to the
OEM harness, before reassembling the door panel. The crossover needs to be
placed behind the door panel. Use foam pads to wrap cables/crossover to
prevent rattling.
Change tweeter
Remove the tweeter cover. Usually it is fixed with 2 or 3 clips. Use a PRY
tool to remove it and be careful. Take it easy and use minimal force. When
loose, disconnect the speaker harness from the tweeter.
Use a Snap-off blade knife or a cutting nipper to remove the top of the
plastic pin that holds the OEM-tweeter. When the tweeter is dismounted, make
sure to remove all material from the pin that was used to fix the OEM-
tweeter.
Attach the 3M double-sided adhesive tape to the sound optimized tweeter
bracket. Mount the new DLS tweeter in the bracket. Remove the protection
plastic from the 3M tape and place the bracket in the OEM tweeter cover. Press
the bracket down, to attach to the OEM tweeter cover.
Connect the crossover with the PnP connector. Use the other adhesive foam to
secure the crossover and cables.
The yellow cable loop is tweeter level select, enabling fine tuning of the high frequencies
- Closed loop = -4dB (Shown in the picture)
- Open loop = Normal
Allow the component kit to play for at least 15-20 hours in order to perform
at its possibly best. This run-in can be made with tone sweep or with just
music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in session the performance and
characteristics will be in the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your country. You can always contact the DLS Helpdesk in Sweden at e-mail: info@dls.se. Information can also be found on our WEB- site www.dls.se. We follow a policy of continuous advancement in development. For this reason, all or part of the specifications and designs may be changed without prior notice.
Specifications
Art. no / CK-CRPP-VO1.6
- Woofer 6.5” / 165 mm with glass fiber cone
- Tweeter 1” / 25 mm silk dome tweeter with accessories
- RMS Power 100 W
- MAX Power 200 W
- Impedance 3 Ohm
- Sensitivity 90dB 1W / 1M
- Freq. range 55 Hz – 25 kHz
- Crossover 4.8 kHz 12dB / Oct with Mundorf caps
DLS Cruise CRPP-VO1.6 Tweeter
- Size 1” / 25.4 mm
- Voice Coil Material CCAW voice coil / Aluminium former
- Frame Glass Fiber Reinforced ABS
- Magnet Neodymium / Copper shorting ring
- Cone Natural silk dome
- Impedance 4 Ohm
- Freq. range 2 kHz – 25 kHz
Electro-Acoustic Parameters:
- Re 3.5 Ohm
- Fs 1992 Hz
- SPL 94 dB 1W/1M
DLS Cruise CRPP-VO1.6 Woofer
- Size 6.5” / 165 mm
- RMS Power 100 W
- MAX Power 200 W
- Voice Coil Size 1” / 25mm
- Voice Coil Material CCAW voice coil / Kapton former
- Basket Glass Fiber Reinforced ABS
- Magnet Ferrite
- Cone Glass Fiber
- Suspension Rubber
- Impedance 2 Ohm
- Freq. range 55 Hz – 5 kHz
Electro-Acoustic Parameters
- Re 1.9 Ohm
- Fs 68.2 Hz
- Mms 16.7 gr
- Cms 0.324
- Vas 8.7L
- Qts 0.84
- Qes 0.96
- Qms 6.6
- Bl 3.76 T.m
- Spl 86.6 dB 1W/1M
- Sd 139 cm²
Impedance VS Frequency
DIMENSION
DLS Cruise CRPP-VO1.6
The DLS component kit speaker is developed to be installed in the front door of your car.
DLS Cruise CRPP-VO1.6 compatible car models
- Car Model Year Front speaker Rear speaker
- Volvo C30 2007-2013 CRPP-VO1.6*
- Volvo S40 2008-2012 CRPP-VO1.6*
- Volvo S80 2007-2017 CRPP-VO1.6*
- Volvo S60 2011-2017 CRPP-VO1.6*
- Volvo V70 2008-2016 CRPP-VO1.6*
- Volvo V40 2012-2016 CRPP-VO1.6*
- Volvo V50 2004-2012 CRPP-VO1.6*
- Volvo V60 2011-2017 CRPP-VO1.6*
- Volvo V60 XC 2016-2017 CRPP-VO1.6*
- Volvo XC70 2008-2016 CRPP-VO1.6*
- Volvo XC60 2009-2017 CRPP-VO1.6*
Disclaimer
The coaxial speaker can be placed in the rear doors. (CRPP-VO1.6CX)
Product markings
- The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.
- This product has been granted with the CE certification mark to show that the product follows the health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).
- DLS products complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.
- DLS is a global partner of the European Mobile Media Association, an organisation that focus on promoting the custom made mobile media installations to consumers
We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>