CRUISE CRPP-UW64 Mid Bass Speakers User Manual
- June 13, 2024
- CRUISE
Table of Contents
CRPP-UW64
User manual
Universal 4 ohm woofer
CRPP-UW64 Mid Bass Speakers
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-UW64. For us, it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you read
this manual, preferably before you start your installation. Keep the manual in
a safe and accessible place for future reference.
Your speakers must be installed correctly in order to work as intended. Make
sure you have all necessary tools nearby before starting and that you are
completely confident in how to process. If you feel the slightest uncertainty;
feel free to take the help of an experienced installer or a car audio dealer.
Warranty
This speaker is covered by warranty, depending on the conditions in the
country where it is sold. If the speaker is returned for service, please
include the original dated receipt with the product.
General
Some sound systems may vary in size of the door speaker. Make sure that your
vehicle has the same size as this speaker, before you start the assembly
DECLARATION OF CONFORMITY
DLS Cruise speakers for vehicles are manufactu-red in accordance with the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval number. They are also marked in accordance with the WEEE-directive 2012/19/EC. The products are also produced in accordance with the EU RoHS directive 2015/863/EU.
Included parts
Included products:
2pcs Woofers
Included in box:
8pcs M4 screws
4pcs Fork terminals
4pcs Flat pin connectors
1pc PRY tool
1pc Manual
Pre installation
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure the
negative terminal from your battery/power source. This will prevent the risk
of damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from
any possible connection belonging to the battery/power source system.
Installation
General installation
Mount the speakers in the door or in the rear shelf of your car. They may fit
in the factory pre-made mounting holes, if not you might have to modify the
fitting. If you want to improve the sound reinforcement you can use a baffle
of MDF-board or similar. For door placements, there are normally speaker rings
that have to be used to make the speaker fit to the door panel.
NOTE! It is important to fasten the speakers properly in order to avoid
bad sound or rattling.
Custom baffle installation
It is very important that the custom baffle are stable and fasten properly,
but it is just as important that it´s shaped in a way that the driver is
allowed to “breathe” correctly. Bass reproduction will be enhanced when the
air flow is free and not obstructed.
Speaker connection
Make sure you connect the cables with correct polarity on the speaker terminals. Observe the markings and size differences on the connectors.
Speaker phasing
To be sure that the CRPP-UW64 woofer are using the correct polarity (phase)
after installation, it is possible to check this easily by using a 1.5 volt
battery.
Connect the battery’s positive and negative pole to the speaker cable. If the
speaker is correctly connected the cone should move outwards. This need to be
tested on all left/ right pairs to make sure all drivers are in phase with
each other.
Note!
Don´t use this testing method on tweeters or other low excursion drivers
without a correct connected high pass crossover.
Crossover settings
DLS recommend using active crossover settings for the UW64 speaker to get
increased power handling and durability.
High pass filter: 60-100 Hz
Low pass filter: 3500-5000Hz
Door insulation
DLS recommends using insulation and/or sound deadening in the car doors. It
lowers the noise from the road/tires and prevent rattles and other noises from
plastic details in the doors.
If you need help deciding what type of door insulation you should use, ask
your DLS distributor for info and guidance.
Running-in time
Allow the tweeters to play for at least 15-20 hours in order to perform at its
possibly best. This run-in can be made with tone sweep or with just music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in session the performance and
characteristics will be in the correct condition. DLS support
For technical assistance, ask your car audio dealer where the product was
sold or the distributor in your country. You can always contact DLS Helpdesk
in Sweden at e-mail: info@dls.se.
Information can also be found on our WEB-site www.dls.se.
We follow a policy of continuous advancement in development. For this reason,
all or part of specifications and designs may be changed without prior notice.
Wiring diagram
Specifications
Art. no | CD-CRPP-UW64 |
---|---|
Woofer | 6.5” / 165mm |
RMS Power | 100W |
MAX Power | 200W |
Impedance | 4 Ohm |
Sensitivity | 86.8dB 1W/1M |
Freq. range | 55-5000Hz |
Technical specifications
Voice coil size | 1” / 25mm |
---|---|
Voice coil material | Copper voice coil / Kapton® former |
Basket | Euro-DIN ventilated reinforced steel frame |
Magnet | High grade ferrite / Ventilated back plate |
Cone | Laminated glass fibre cone |
Dust cap | Santoprene® rubber dust cap |
Spider | Nomex® with woven tinsel leads |
Terminal | Twin terminal |
Electro-Acoustic Parameters
Re | 3.2 Ohm |
---|---|
Fs | 63.2Hz |
Mms | 15.8gr |
Cms | 0.399 |
Vas | 10.9L |
Qts | 0.66 |
Qes | 0.89 |
Qms | 2.512 |
Bl | 4.74T.m |
SPL | 86.8dB 1W/1M |
Sd | 139cm² |
Dimensions Impedance VS Frequency
Product markings
The
crossed-out wheelie bin symbol means that the product, literature and
packaging included must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.
**** This product has been granted with the CE certification mark to show
that the product follows the health, safety, and environmental protection
standards for products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS Directive for
the European Union. In common with all Electrical and Electronic Equipment
(EEE) the product should not be disposed of as household waste. Alternative
arrangements may apply in other jurisdictions. DLS is a global partner of the
European Mobile Media Association, an organisation that focus on promoting the
custom made mobile media installations to consumers.
We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.
DLS
speakers are engineered by DLS Sweden, a part of:
Winn Scandinavia AB
Elementvägen 15 – SE-702 27 Örebro – Sweden
Tel: +46 19 20 67 65 – E-mail: info@dls.se
www.dls.se
Designed & Sound tuned in Sweden.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>