Shuttle DS50U Fanless Mini PC Intel Raptor User Manual
- June 16, 2024
- Shuttle
Table of Contents
User Manual
For the: DS50U
DS50U Fanless Mini PC Intel Raptor
Shuttle®
XPC Installation Guide
Copyright
©2023 by Shuttle
Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a
retrieval sys- tem, translated into any language, or transmitted in any form
or by any means such as electronic, mechanical, magnetic, optical, chemical,
photocopy, manual, or otherwise, without prior written permission from
Shuttle® Inc.
Other brands and product names used herein are for identification purposes
only and may be trademarks of their respective owners.
Disclaimer
Shuttle® Inc. shall not be liable for any incidental or consequential
damages resulting from the performance or use of this product.
Shuttle® Inc. makes no representation or warranty regarding the contents of
this ma- nual. Information in this manual had been carefully checked for
accuracy;however, no guarantee is given as to the correctness of the contents.
For continuing product improvement, Shuttle® Inc. reserves the right to revise
the manual or make changes to the specifications of this product at any time
without notice and obligation to any person or entity regarding such change.
The information contained in this manual is provided for general use by
customers.
This device complies to Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
- This device may not cause harmful interference.
- This device must withstand any background interference including those that may cause undesired operation.
Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel and Pentium are registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice
Other brand and product names used herein are for identification purposes only
and may be trademarks of their respective owners.
Safety Information
Read the following precautions before setting up.
CAUTION
Incorrectly replacing the battery may damage this co-mputer. Replace only with
the same or equivalent type recommended by the manufacturer. Disposal of used
batteries according to the manufacturer’s instructions.
Installation Notices
Do not place this device underneath heavy loads or in an unstable position.
Do not expose this device to high levels of direct sunlight, high-humidity or
wet conditions.
Do not use or expose this device around magnetic fields as magnetic
interference may affect the performance of the device.
Do not block the air vents to this device or impede the airflow in any way.
Driver and Software Installation
• Motherboard Driver DVD
The DVD contents attached in DS50U Series motherboard are subject to change
without notice.
The Motherboard Driver DVD contains all the motherboard drivers necessary to
optimize the performance of this Shuttle Xvision in a Windows® OS. Install
these drivers after installing Microsoft® Windows®.
Insert the attached DVD into your DVD-ROM drive. The DVD AutoRun screen should
appear. If the AutoRun screen does not appear, double click on Autorun icon in
My Computer to bring up Shuttle Mainboard Software Setup screen.
Navigation Bar Description:
Auto Install Driver.
Install Intel Rapid Storage Tech. Driver.
User Manuals – Motherboard Manual, Quick Guide.
Link To Shuttle Website – Link to shuttle website homepage.
Browse This DVD – Allows you to see contents of this DVD.
• User Manuals
Install Adobe Reader 9.5
MotherBoard Manual
Quick Guide
www.shuttle.com
Appendix
Starting BIOS
AMIBIOS has been integrated into many motherboards for over a decade. In the
past, people often referred to the AMIBIOS setup menu as BIOS, BIOS setup, or
CMOS setup.
American Megatrends refers to this setup as BIOS. Specifically, it is the name
of the AMIBIOS BIOS setup utility. This chapter describes the basic navigation
of the BIOS setup screens.
Enter the BIOS
To enter the BIOS setup screens, follow the steps below:
Step1. Power on the motherboard.
Step2. Press the
Step3. After you press the
You can access the other setup screens from the main BIOS setup menu, such as
the Chipset and Power menus.
This manual describes the standard look of the BIOS setup screen. The
motherboard manufacturer has the ability to change any and all of the settings
described in this manual. This means that some of the options described in
this manual do not exist in your motherboard’s AMIBIOS.
In most cases, the
BIOS Setup Menu
The main BIOS setup menu is the first screen that you can navigate. Each main
BIOS setup menu option is described in this user’s guide.
The Main BIOS setup menu screen has two main frames. The left frame displays
all the options that can be configured. “Grayed-out” options cannot be
configured.
Options is blue can be.
The right frame displays the key legend. Above the key legend is an area
reserved for a text message. When an option is selected in the left frame, it
is highlighted in white.
Often a text message will accompany it.
AMIBIOS has default text messages built into it. The motherboard manufacture
retains the option to include, leave out, or change any of these text
messages. They can also add their own text messages. Because of this, many
screen shots in this manual are different from your BIOS setup screen.
The BIOS setup/utility uses a key-based navigation system called hot keys.
Most of the BIOS setup utility hot keys can be used at any time during the
setup navigation process. These keys include
| Hot Key | Description |
|---|
→ Left
← Right| The Left and Right
↑ Up
↓ Down| The Up and Down
+- Plus/ Minus| The Plus and Minus
Tab| The
Fl| The
F4| The
ESC| The
Enter| The
Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup
screen.
You can always return to the Main setup screen by selecting the Main tab.
There are two Main Setup options. They are described in this section. The Main
BIOS Setup screen is shown below. System Time/System Date
Use this option to change the system time and date. Highlight System Time or System Date using thekeys. Enter new values through the keyboard. Press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00.
Advanced
Select the Advanced tab from the BIOS setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item.
You can display an Advanced BIOS Setup option by highlighting it using thekeys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages. **TPM Configuration** **Security Device Support** This item allows you to enable or disable fTPM. ****The choice: Enabled, Disabled. ****Power Management Configuration **Wake Up By USB (S3)** This item allows you to enable or disable system wake up by USB (S3). ****The choice: Enabled, Disabled. **EuP Function** This item allows you to enable or disable system EuP function in S4/S5. ****The choice: Enabled, Disabled. **Power-On after Power-Fail** This item allows you to set system power on automatically after AC power restored. ****The choice: Power On, Former-sts, Power Off, Power On by LAN, Power On by RTC. **PowerOn by RTC Alarm** When enabled, System will wake on the hr::min::sec specified. ****The choice: Enabled, Disabled. **Wake Up By LAN** This item allows you to enable or disable system wake on by onboard LAN chip. ****The choice: Enabled, Disabled. **CPU Configuration** You can use this screen to select options for the CPU Configuration Settings. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown below. The CPU Configuration setup screen varies depending on the installed processor. **Active Efficient-cores** This item allows you to enable E-cores in each processor package. ****The choice: All, 0, 1, ~n-1. **Intel(R) V. T.** When enable, a VMM can utilize the additional hardware capabilities provided by vanderpool Technology. ****The choice: Enabled, Disabled. CPU support, item appear. **C State Support** This item allows you to enable or disable CPU C State. ****The choice: Enabled, Disabled. **EIST** This item allows you to enable or disable Enhanced lntel SpeedStep(R) Technology. ****The choice: Enabled, Disabled. **Intel(R) Speed Shift Technology** This item allows you to enable or disable Intel(R) Speed Shift Technology(ISST). ****The choice: Enabled, Disabled. **Turbo Mode** This item allows you to enable or disable Turbo Mode. ****The choice: Enabled, Disabled. The CPU Configuration setup screen varies depending on the installed processor. **Intel(R) HT Technology** This item allows you to enable or disable Intel(R) HT Technology. ****The choice: Enabled, Disabled. **SATA Configuration** **SATA Mode Selection** This item allows you to set the SATA Mode Selection. ****The choice: AHCI, RAID. **OnBoard Device Configuration** High Definition Audio
This item allows you to enable or disable system High Definition Audio.
**The choice: Enabled, Disabled.
CNVi Function
This item allows you to enable or disable CNVi module.
**The choice: Enabled, Disabled.
M.2 Device Select
M.2 PCIe and SATA device selection.
**The choice: Auto, PCIE, SATA.
Onboard LAN1/2 Function
This item allows you to enable or disable LAN1/2 Function.
**The choice: Enabled, Disabled.
Onboard LAN BOOT ROM
This item allows you to enable or disable Onboard LAN BOOT ROM.
**The choice: Enabled, Disabled.
IGD Memory Size Select
Allows you to select the size of system memory used by the internal graphics device.
**The choice: 32MB, 64MB, 128MB, 256MB, 512MB.
Intel(R) VT-d
This item allows you to enable or disable Intel(R) VT-d.
**The choice: Enabled, Disabled.
Serial Port Configuration
Option are in its sub-menu.
Pressto enter the sub-menu of detailed options. Serial Port 1/2
Enalbed/Disabled Serial Port(COM).
**The choice: Enabled, Disabled.
Change Mode
COM mode select.
**The choice: RS232, RS422, RS485.
Termination(120ohm)
This item allows you to enable or disable the termination for RS422 and RS485.
**The choice: Enabled, Disabled.
Change Settings
This item allows you to set Serial Port1/2 address.
**The choice: 3F8h, 2F8h, 3E8h, 2E8h.
Hardware Health Configuration** Product Information
Insert Serial Number
This item allows you to insert Serial Number.
Insert UUID
This item allows you to insert UUID.
Boot
Select the Boot tab from the BIOS setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Settings Configuration, to go to the sub menu for that item.
You can display an Boot BIOS Setup option by highlighting it using thekeys.
All Boot BIOS Setup options are described in this section.
The Boot BIOS Setup screen is shown below. The sub menus are described on the following pages.
Bootup Num-Lock
Select NumLock state after system bootup.
**The choice: Enabled, Disabled.
Boot from USB device/Card-Reader
Enabled/Disabled onboard USB storage/Card-Reader boot function.
**The choice: Enabled, Disabled.
Fast Boot Function
This item allows you to enable or disable Fast Boot Function.
**The choice: Enabled, Disabled.
Boot Device Priority (Boot Option #1/2/3/….)
Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu.
Security
Select the Security tab from the BIOS setup screen to enter the Security BIOS Setup screen. You can display an Security BIOS Setup option by highlighting it using thekeys. All Security BIOS Setup options are described in this section. Supervisor Password
The Security Setup screen is shown below. The sub menus are documented on the following pages.
Indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
User Password
Indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
Change Supervisor Password**
Select Change Supervisor Password from the Security Setup menu and press. **Enter New Password:** Type the password and press . The screen does not display the char- acters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes. **Change User Password** Select Change User Password from the Security Setup menu and press . **Enter New Password:** Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes. **Password Login control** This item allows user to adjust Password Login control. ****The choice: Setup, Boot, Both. **Flash Write Protection** Choose [Enabled] to avoid virus destroy BIOS. If you want to flash BIOS, you must set it [Disabled]. ****The choice: Enabled or Disabled. **Exit** Select the Exit tab from the BIOS setup screen to enter the Exit BIOS Setup screen. You can display an Exit BIOS Setup option by highlighting it using the keys. All Exit BIOS Setup options are described in this section. The Exit BIOS Setup screen is shown below.  **Save Changes and Exit** When you have completed the system configuration changes, select this option to leave BIOS Setup and reboot the computer so the new system configuration parameters can take effect. Select “Save Changes and Exit” from the Exit menu and press . Save Configuration Changes and Exit Now? [Ok] [Cancel] appears in the window. Select Ok to save changes and exit. **Exit Without Saving Changes** Select “Exit without Saving Changes” from the Exit menu and press . Select Ok to discard changes and Exit. **Load Defaults Settings** BIOS automatically sets all BIOS Setup options to a complete set of default settings when you Select this option. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal BIOS Setup options if your computer is experiencing system configuration problems. Select Load Optimal Defaults from the Exit menu and press . Select Ok to load optimal defaults.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>