VEVOR AX-ZNGZD-001 LED Work Light Instruction Manual

: June 16, 2024
: VEVOR

Table of Contents

VEVOR AX-ZNGZD-001 LED Work Light
Product Information
Product Usage Instructions
IMPORTANT SAFETY INSTRUCTIONS
Switch Button Manual (AX-ZNGZD-003)
PACKAGE LIST
NEED HELP? CONTACT US!
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VEVOR AX-ZNGZD-001 LED Work Light

Product Information

Specifications

Model: AX-ZNGZD-001, AX-ZNGZD-002, AX-ZNGZD-003

Product Usage Instructions

Important Safety Information

Before using the product, please read and understand the following safety rules:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Failure to observe the following safety rules may result in FIRE, ELECTRICAL SHOCK INJURY, or EXPOSURE TO EXCESSIVE ULTRAVIOLET RADIATION.

Tripod Work Light

The tripod work light comes with a two-color controller program and a remote control manual. Follow the steps below to operate the work light:

Step 1: Powering On

After connecting the work light to a power source, turn on the red switch of the left lamp.
Long press the left (ON/OFF) button on the remote control for 5 seconds.

Step 2: Adjusting Brightness

To adjust the brightness of the lamp:

Press the lamp brightness + button to increase the brightness by 10%.
Press the lamp brightness – button to decrease the brightness by 10%.
The maximum brightness is 100%, and the minimum brightness is determined by the initial setting.

Step 3: Controlling Color Temperature

To control the color temperature of the lamp:

Press the color temperature button to cycle through cold light, warm light, and neutral light.

Step 4: Clearing Code

To clear the code and reset the remote control:

Long press the C button on the remote control for 5 seconds.
The lamp will blink to indicate that the code has been cleared.
After clearing the code, the lamp can only be controlled using the switch, not the remote control.

Step 5: Scene 1-3

Scene 1-3 refers to controlling multiple lamps with one remote control. For detailed instructions, please refer to the user manual.

Tips

One remote control can control more than one lamp, but multiple remotes cannot control a lamp simultaneously.
Press the remote control buttons using the finger side of your finger, not your fingernail.
The AX-ZNGZD-003 model cannot be used while charging to minimize battery life degradation due to cyclic charging.

FAQ

Q: Where can I find technical support and an e-warranty certificate?
A: You can find technical support and an e-warranty certificate at www.vevor.com/support.
Q: Can I save half compared to top major brands when buying tools from VEVOR?
A: The expression “Save Half, Half Price” used by us represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands. However, it does not necessarily cover all categories of tools offered by us. We recommend verifying carefully when placing an order to determine the actual savings.

Please read and understand this entire manual before attempting to assemble, operate or install the product

WARNING

Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
BE EXTREMELY CAREFUL WHEN USING THIS DEVICE. Improper use of this work light can result in injury or death. Follow all safeguards stated in this manual in addition to normal safety precautions in working with electrical devices.DO NOT attempt to service this device./SEA EXTREMADAMENTE CUIDADOSO AL USAR ESTE DISPOSITIVO
When using outdoor portable work lights, always follow basic safety precautions to reduce the risk of electric shock and personal injury.
Failure to observe the following safety rules may result in
Use only 3-wire UL-listed outdoor extension cords that have 3-prong grounded plugs and grounded receptacles that accept the work light’s plug.
Use only with an extension cord for outdoor use, such as with cord type SEW, SEOW SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
To avoid electrical shock, do not use near water or in areas where water may accumulate. Keep work light at least 16 ft. from pools or spas. Keep plugs dry. Use only Ground Fault Circuit Interrupter (GFCI) protecting receptacles when using this work light in wet or damp locations. Receptacles are available with built-in GFCI protection and are to be used for this measure of safety

IMPORTANT SAFETY INSTRUCTIONS

This portable luminaire has a polarized plug(one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug willﬁt in a polarized outlet only one way.lf the plug does notﬁt fully in the outlet, reverse the plug. lf it still does notﬁt, contact a gualiﬁed electrician. Never use an extension cord unless plug can be fully inserted. Do not alter the plug

SAVE THESE INSTRUCTIONS

VEVOR -AX-ZNGZD-001-LED-Work- Light-fig-1

Ensure the work light is not placed on a surface with a greater than 8° slope If the light heads are either too loose or tight after adjustment. tighten the screw in the shaft with the wrench (A4) /

Tripod work light two-color controller program
Remote Control Manual

The factory setting is in accordance with Scene 1, so you can directly follow Step 3 in Scene 1 to perform remote control.
Scene 1: One remote control to control 1 set (1 left and 1 right) of left and right lamps, respectively

Step 1: After powering on, turn on the red switch of the left lamp, long press the left (ON/OFF) of the remote control for 5 seconds, then the lamp starts to blink; that is, the code is successful.
Step 2: Turn on the red switch of the right light, long press the left ON/OFF of the remote control for 5 seconds, then the light starts to blink; that is, the code is successful.
Step 3: Use the ON/OFF button of successful code pairing to control the light separately.

Scene 2. One remote control-control 1 set of lights (1 left and 1 right)

Step 1: After powering on, turn on the red switch of the left and right lamps so that 1 set of lamps will be on at the same time;
Step 2: Pair code. Long press either left or right side ON/OFF for 5 seconds. At this time, the lights start to blink, that is, pair code successfully.
Step 3: Use the corresponding ON/OFF key for switch control

Scene 3: One remote control to control multiple sets of lights

Step 1: After powering on, turn on all the red switches of the left and right side lights of the multiple sets of lights.
Step 2: Pair code. Long press the left and right side ON/OFF for 5 seconds. At this time, the lights start flashing, that is, pair code successfully.
Step 3: Use the corresponding ON/OFF key for on or off control. General function
Brightness +/- :Maximum brightness:100%. Minimum Brightness: 10%.
Color temperature : cold light – warm light – neutral light. Cycle control
Clear code : Long press the C button for 5 seconds to clear the code; the light will blink. Blinking means that the clear code is completed. At this time, the remote control can not be operated and can only be controlled by the switch. If you want to control it by remote control, please refer to Scenes 1-3.
Neutral color temperature and brightest mode, LED white light, and warm light bulb on at the same time

Tips

****| 1. One remote control can control more than one lamp. Multiple

remotes cannot control a lamp at the same time.

---|---
****| 2. The remote control needs to be pressed with the finger side of

your finger, not your fingernail.

****| 3. To minimize battery life degradation due to cyclic charging, the

AX-ZNGZD-003 cannot be used while charging.

Switch Button Manual (AX-ZNGZD-003)

When you choose not to use the remote control to operate the light, you can use the round on/off button to the left of the USB port

Turn on the light: With a single click, randomly light up one of the left and right lights.
Switching status: When one light is on, double click, switch the other light on (color temperature remains unchanged), double click again, and both lights are on. Cycle control.
Color temperature adjustment: When the light is on, click within 5 seconds after the last operation. Cycle control.
Turn off the light: single click at least 5 seconds after the last operation.

PACKAGE LIST

Data cable × 1（Battery version）
Remote control unit× 1
Wrench× 1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation

We continue to be committed to providing you tools with at competitive prices. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean covering all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us a technical Support and an E-Warranty Certificate This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.’