YUEYINPU P33-1 Pedal Wireless Foot Pedal Double Switch Music User Manual

YUEYINPU P33-1 Pedal Wireless Foot Pedal Double Switch Music

P33-01 Pedal
USER MANUAL

Product description

Thank you for purchasing our wireless pedal. This product can be used on Android, Windows, iOS system by fixed button to achieve wireless & silently switching pages by stepping on the pedal. By this way, you can play music without using your hands to switch pages of sheet music. Hope this product can bring you convenience and happiness.

How to connect

Power Switch:

1. When you turn the power to “ON” , the pedal will into statue of waiting for pairing. Firstly, the signal light flashes green which means that it is searching for the connected device last time. And if yes, they will be connected automatically. If without success connection after 10 seconds, the signal light will flash Red-Green-Blue alternately which means that it is waiting to be paired to new device. For the first use, after the signal light flashes green for 10 seconds and begin to flash Red-Green-Blue alternately, then you can turn on the Bluetooth of your device and wait until “P33-01 Pedal” shows, click it to connect.
2. When you turn the power to “OFF” , means to turn off the pedal.

Description of function

1. After connecting to your device successfully, the pedal is on default setting mode 1 and mode 1 will light blue. There are five switch buttons below five modes. You can press the switch button to change to corresponding mode.
2. There are five working modes on this pedal, different mode correspond different function out­put(refer to chart below)
3. PS: It works like wireless keyboard, PgUp & PgDn, left and right, up and down, left and right mouse buttons, space and enter.
4. Repeat Switch:
5. When the “Repeat” is OFF, step on the pedal once to switch one page, no matter long press or short press.
6. When the “Repeat” is ON, long press the pedal and the pages will keep switching. If that is the case, make sure to set “Repeat” to the OFF posi­tion.

Indication for signal light

Signal light and power light are the same light, it will automatically switch the function according to the needs of the scene.

1. Signal light:
2. Battery indicator light

Dormant time and way to wake up

1. Dormant
2. If you turn on the power button, but can not connected successfully, then it turns into the state of dormant.
3. A device that was originally connected suddenly turns off Bluetooth, then it turns into the state of dormant.
4. Wake Up
   Only need to step on anyone of the pedals to wake up the pedal again.

iOS connection tip
When to connect with iOS system, the virtual key­board of the original iOS system will be locked. At that time, only need to press on the left and right pedals at the same time, then it can be unlocked, and release the iOS virtual keyboard.

Charging

1. Use the provided Type-C charging cable and select the 5V USB adapter, it takes about 3 hours to full charge.
2. When charging, the middle light will light up red, and when it is full, the light will turn to green.

Reset Switch
There is a small reset pin hole next to the charging port. When the pedal is connected with any device, use a small pin and stick it into the hole, press the switch inside for 2~3 seconds, the pedal will be reset and back to the original statue. The signal light will flashes red-green-blue alternately and wait to pair to device.

Product Specification

Support many apps:
PM Reader, Goodnotes, Apple Books, Teleprompt+3, Foxit Reader, IMSLP, NextPage3, Newzik, DD Gigbook, PDF Expert, forScore, Kindle, OnSong, WPS Office, Document, Tabs, MusicReader PDF, Piascore, Musicnotes, Paperless Music, SongBook, unrealbook, MobileSheets, etc.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired op­eration.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pur­suant to Part 15 of the FCC Rules. These limits are de­signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre­quency energy, and if not installed and used in accor­dance with the instructions, may cause harmful inter­ference to radio communications.
• However, there is no guarantee that interference will not occur in a par­ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV tech­nician for help.

Made in China

Documents / Resources

| YUEYINPU P33-1 Pedal Wireless Foot Pedal Double Switch Music [pdf] User Manual
P33-1 Pedal Wireless Foot Pedal Double Switch Music, P33-1, Pedal Wireless Foot Pedal Double Switch Music, Wireless Foot Pedal Double Switch Music, Pedal Double Switch Music, Double Switch Music, Switch Music
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>