Lucci decor 011842 Akira 1LT Tall Pendant Instruction Manual
- June 4, 2024
- Lucci decor
Table of Contents
Lucci decor 011842 Akira 1LT Tall Pendant
Warranty
- This luminaire is covered by a 12-month warranty. The warranty is from the date of purchase, not the date of installation.
- If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
- Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Requirements
- This luminaire must be assembled and installed by a licensed electrician.
- All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
- E. g AS/NZS 3000 Electrical Installations.
- This luminaire is a Class I product and must be earthed during wiring and installation.
- Do not exceed the maximum wattage rating.
- Select a suitable location for installation:
- This luminaire is suitable for indoor use only.
- The mounting point must support 2 times the weight of the luminaire.
- Ensure the luminaire is not installed in the direct line of an air vent/system.
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required.
- Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure no components are missing before assembling.
- If parts are missing, return the complete product to the place of purchase for inspection or replacement.
- Check whether the luminaire has been damaged during transport.
- Do not operate/install any product which appears damaged in any way.
- Return the complete product to the place of purchase for inspection, repair or replacement.
- Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Installation Directions
- Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
- Remove the mounting bracket (B) from the canopy (F) by loosening the screws (E) on the side.
- Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
- Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (C) and anchors (A).
- Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
- Determine the suspension length required for your installation location. If the length of the suspension cord (H), requires adjustment, loosen the cord anchorage (G) and adjust to the desired length.
- When completed, tighten the cord anchorage (G), take care not to overtighten and damage the cord (H).
- Connect the mains supply wire to the terminal block (D).
- Ensure the wires are secure, and no bare wires are exposed.
Mains Supply Wire Earth
- Yellow/Green Neutral –
- Blue or Black Live
- Brown or Red
Luminaire Wire / Terminal Block
- Yellow/Green
- Blue or N
- Brown or L
NOTE
This luminaire is a Class I product and must be earthed during wiring and
installation. Ensure the earth wire from the mounting bracket (B) and canopy
(F) are connected to the earth terminal on the terminal block (D). Install the
canopy (F) onto the mounting bracket (B) and secure it by tightening the
screws (E) on the side. Install a GX53 lamp (J – not included) into the lamp
holder (I). Do not exceed the maximum wattage rating. Lucci LEDlux SKU# 121354
or SKU# 121359 lamp is recommended. After the installation is complete, switch
on the luminaire to test and enjoy your new lighting product.
Installation Instructions
Safety Tips
Always ensure the power is OFF and the luminaire has cooled down before
performing any maintenance, cleaning, changing the lamp or making any
adjustment to the luminaire.
- To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
- Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
SKU #| 011842| 011843
Colour| Black| White
Rated Voltage| 220-240V~ 50Hz
Rated Wattage| 12W Max.
Lamp Holder| GX53
Weight| 2.0kg
Canopy
Dimensions
|
H:25mm Dia:100mm
Luminaire
Dimensions
| H:345mm Dia:315mm Susp:2000mm Max.
Lucci LEDlux SKU# 121354 or SKU# 121359 lamp is recommended.