Shuttle DS50U Series Fanless Mini PC With Intel Raptor User Guide

June 16, 2024
Shuttle

Shuttle-LOGO

Shuttle DS50U Series Fanless Mini PC With Intel Raptor

Specifications

  • USB 3.2 Gen 2 Ports
  • USB 3.2 Gen 1 Ports
  • Power LED
  • Hard Disk Drive LED
  • Power Button
  • MIC-in
  • Headphones
  • HDMI Port
  • DisplayPort
  • COM Port (RS232/RS422/RS485) (BIOS Setting)
  • USB 2.0 Ports

Memory Module Installation

  1. Locate the SO-DIMM and paste the thermal pad (50*15 mm) on the motherboard, which can effectively reduce its temperature.

  2. Install the 1st memory module into the DIMMA1 slot.

    • DIMMB1 (Top)
    • DIMMA1 (Bottom)
  3. Align the notch of the memory module with the one of the relevant memory slot.

    • SO-DIMM slot Notch
    • Cutout
    • Thermal Pad (50*15 mm)
  4. Gently insert the module into the slot in a 45-degree angle.

  5. Carefully push down the memory module until it snaps into the locking mechanism and put the mylar back in place.

  6. Install the 2nd memory module into the DIMMB1 slot (proceed with steps B3 to B5) and paste the thermal pad, as shown.

    • DIMMB1 (Top)

Hardware Installation

Begin Installation:

  1. For safety reasons, please ensure that the power cord is disconnected before opening the case.
  2. As shown, unscrew the four screws of the chassis cover and remove the cover.

M.2 Device Installation

Notice for M.2 slots: When CN3 is occupied by NVME device, CN2 only supports SATA interface.

  1. Locate the M.2 key slots on the motherboard.
    • M.2 2280 M key slot
  2. Install the M.2 device into the M.2 slot and secure with the screw.

HDD or SSD Installation

  1. Remove the rack.
  2. Mount the HDD or SSD into the bracket with four screws.

Complete

  1. Replace and affix the case cover with four screws. Turn your DS50U upside down.
  2. Connect the power cord.
  3. Complete.
    • Connect the Serial ATA and power cable to the HDD or SSD.
    • Install the HDD or SSD & bracket in the chassis.

FAQ

How many USB ports does the DS50U series have?

The DS50U series has a total of 5 USB ports. 2 USB 3.2 Gen 2 ports, 2 USB 3.2 Gen 1 ports, and 1 USB 2.0 port.

What type of memory modules does the motherboard support?

The motherboard supports 1.1 V DDR5 SO-DIMM memory modules.

What is the purpose of the thermal pad in memory module installation?

The thermal pad is used to effectively reduce the temperature of the memory module.

More information on this product can be found at: https://bit.ly/DS50USERIES

Product Overview

  1. USB 3.2 Gen 2 Ports
  2. USB 3.2 Gen 1 Ports
  3. Power LED
  4. Hard Disk Drive LED
  5. Power Button
  6. MIC-in
  7. Headphones
  8. HDMI Port
  9. DisplayPort
  10. COM Port (RS232/RS422/RS485) (BIOS Setting)
  11. USB 2.0 Ports
  12. Giga LAN Port
  13. 2.5Giga LAN Port
  14. Power Jack (DC IN)
  15. COM/VGA Port (RS232 only) (Option)
  16. Connector for WLAN antenna
  17. External Power SW & Clear CMOS
  18. Kensington® Lock Hole

Hardware Installation

A. Begin Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

  1. As shown, unscrew the four screws of the chassis cover and remove the cover.
    The product’s colour and specifications may vary from the actually shipped product.

B. HDD or SSD Installation

  1. As shown, remove the rack.
  2. Mount the HDD or SSD into the bracket with four screws.Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-FIG-3
  3. Connect the Serial ATA and power cable to the HDD or SSD.
  4. Install the HDD or SSD & bracket in the chassis.Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-FIG-4

C. Memory Module Installation

This motherboard does only support 1.1 V DDR5 SO-DIMM memory modules.

  1. Locate the SO-DIMM and paste the thermal pad (50*15 mm) on the motherboard, which can effectively reduce its temperature.
  2. Install the 1st memory module into the DIMMA1 slot.Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-FIG-5
  3. Gently insert the module into the slot in a 45-degree angle.
  4. Align the notch of the memory module with he one of the relevant memory slot.
  5. Carefully push down the memory module until it snaps into the locking mechanism and put the mylar back in place.
  6. Install the 2nd memory module into the DIMMB1 slot (proceed with steps B3 to B5) and paste the thermal pad, as shown.

D. M.2 Device Installation

Notice for M.2 slots: When CN3 is occupied by NVME device, CN2 only support SATA interface.

Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-
FIG-9

DS50U only support one NVME device.

  1. Locate the M.2 key slots on the motherboard.
    M.2 2280 M key slot

  2. Install the M.2 device into the M.2 slot and secure with the screw.
    Pasting a thermal pad on the M.2 SSD can effectively reduce its temperature.

E. Complete

  1. Please replace and affix the case cover with four screws. Turn your DS50U upside down.
  2. Connect the power cord.
  3. Complete.Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-FIG-12
    Please press the “Del” key while booting to enter BIOS. Here, please load the optimised BIOS settings. Operation Position: Please make sure to use either the supplied feet or the VESA mount.

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries in accordance with the laws of your country.

All bundled parts, power cord included, shall not be used without this product.

WARNING
THIS PRODUCT CONTAINS A BUTTON BATTERY

  • If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours.
  • Keep batteries out of reach of children.
  • If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device meets the requirements for the EU conformity in accordance to the currently valid EU directives.

Product Overview

  1. USB 3.2 Gen 2 Ports
  2. USB 3.2 Gen 1 Ports
  3. Power LED
  4. Hard Disk Drive LED
  5. Power Button
  6. MIC-in
  7. Headphones
  8. HDMI Port
  9. DisplayPort
  10. COM Port (RS232/RS422/RS485) (BIOS Setting)
  11. USB 2.0 Ports
  12. Giga LAN Port
  13. 2.5Giga LAN Port
  14. Power Jack (DC IN)
  15. COM/VGA Port (RS232 only) (Option)
  16. Connector for WLAN antenna
  17. External Power SW & Clear CMOS
  18. Kensington® Lock Hole

Hardware Installation

A. Begin Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

  1. As shown, unscrew the four screws of the chassis cover and remove the cover.

B. HDD or SSD Installation

  1. As shown, remove the rack.
  2. Mount the HDD or SSD into the bracket with four screws.
  3. Connect the Serial ATA and power cable to the HDD or SSD.
  4. Install the HDD or SSD & bracket in the chassis.

C Memory Module Installation

This motherboard does only support 1.1 V DDR5 SO-DIMM memory modules.

  1. Locate the SO-DIMM and paste the thermal pad (50 x15 mm) on the motherboard, which can effectively reduce its temperature.
    The product’s colour and specifications may vary from the actually shipped product.

  2. Install the 1st memory module into the DIMMA1 slot.

  3. Align the notch of the memory module with the one of the relevant memory slot.

  4. Gently insert the module into the slot in a 45-degree angle.

  5. Carefully push down the memory module until it snaps into the locking mechanism.

  6. Install the 2nd memory module into the DIMMB1 slot (proceed with steps B3 to B5) and paste the thermal pad, as shown.

D. M.2 Device Installation

Notice for M.2 slots: When CN3 is occupied by NVME device, CN2 only support SATA interface.

DS50U only support one NVME device.

  1. Locate the M.2 key slots on the motherboard.
  2. Install the M.2 device into the M.2 slot and secure with the screw.
    Pasting a thermal pad on the M.2 SSD can effectively reduce its temperature.

E. Complete

  1. Please replace and affix the case cover with four screws. Turn your DS50U upside down.
  2. Connect the power cord.
  3. Complete.
    Please press the “Del” key while booting to enter BIOS. Here, please load the optimised BIOS settings.
    Operation Position: Please make sure to use either the supplied feet or the VESA mount.

Motherboard Illustration

Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-
FIG-13

  1. USB 3.2 Gen 2 Ports
  2. USB 3.2 Gen 1 Ports
  3. Power LED
  4. Hard Disk Drive LED
  5. Power Button
  6. MIC-in
  7. Headphones
  8. DDR5 SO-DIMM Slots
  9. Processor
  10. SATA 3.0 6Gb/s connector
  11. M.2 2280 M key slot
  12. M.2 2280 M key slot
  13. M.2 2230 E Key Slot
  14. Battery Connector
  15. USB 2.0 Ports
  16. DisplayPort
  17. HDMI Port
  18. COM Port
  19. Giga LAN Port
  20. 2.5Giga LAN Port \ 2.5Giga
  21. Power jack (DC IN) \ DC

Jumper Settings

  1. Connector for SD Card Reader Daughter Board (CR005)

  2. AC Back Auto Power ON

  3. COM 2 Port \ COM 2

  4. COM 1 & COM 2 Power Switch

COM PORT Pin 9 “Ring Indicator” (RI) configuration:

Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-
FIG-18

  1. VGA connector \ VGA

Shuttle-DS50U-Series-Fanless-Mini-PC-With-Intel-Raptor-
FIG-20

  1. External Power SW & Clear CMOS

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals