SEALEY MAC10S 12V Tyre Inflator Emergency Puncture Sealant Kit Instructions

SEALEY MAC10S 12V Tyre Inflator Emergency Puncture Sealant Kit

Product Information

12V Tyre Inflator + Emergency Puncture Sealant Kit

Specifications

• Model No: MAC10S
• Original Language Version: MAC10S Issue 1 31/10/19

Safety Instructions

• Stop somewhere safely away from other traffic. Try to avoid causing an obstruction to others.
• Make sure your handbrake is on and the car ignition is off.
• Turn on the vehicle’s hazard lights.
• Ensure you are visible to other road users while using the equipment.
• If available, wear a high-vis vest and set up a warning triangle.
• Keep the compressor clean and in good condition.
• Replace or repair damaged parts. Use recommended parts only.
• Unauthorized parts may be dangerous and will invalidate the warranty.
• Keep children and non-essential persons away from the work area.
• Do not inflate any item beyond its maximum specified pressure.
• The 12-volt accessory plug must not be replaced with any other type of plug or electrical supply.
• Do not use flammable solids, liquids, or gases.
• Do not direct the inflation hose connector head at yourself, others, or animals.
• Do not leave the compressor operating unattended. Always monitor it and the inflation pressure.
• Do not carry by the hose or yank the hose from an inflation valve.
• Do not pull the plug from the accessory socket using the lead.
• Do not get the compressor wet or use it in the rain.
• Do not use the compressor for a task that it is not designed for.
• Do not operate the compressor when you are tired or under the influence of alcohol, drugs, or intoxicating medication.
• Do not operate the compressor if any parts are missing or the compressor is damaged, as this may cause failure and/or personal injury.
• Do not open the unit.

Product Usage Instructions

General Notes

• Before using the tyre inflator and puncture sealant kit, please ensure that you have read and understood the safety instructions provided above.
• Check the tyre for physical signs of damage. If the hole or tear is greater than 6mm, it is probably too big to fix and you should consider seeking assistance.
• Do not pull out any objects stuck in the tyre, as this might repair harder to achieve. If possible, work on the tyre with the hole/tear near the lowest point of the tire, as the sealant will work better that way.

Operation

Step 1: Preparation

1. Stop the vehicle somewhere safely away from other traffic to avoid causing obstructions.
2. Ensure the handbrake is engaged and the car ignition is turned off.
3. Turn on the vehicle’s hazard lights to alert other road users.
4. If available, wear a high-vis vest and set up a warning triangle for added safety.

Step 2: Connect the Tyre Inflator

1. Locate the tire valve on the flat or deflated tire.
2. Connect the tire valve connector from the inflator kit to the valve securely.

Step 3: Inflate the Tyre

1. Turn on the tire inflator using the On/Off switch.
2. Monitor the pressure gauge and inflate the tire to the recommended pressure level.
3. Do not exceed the maximum specified pressure for the tire.

Step 4: Deflate and Seal

1. If necessary, use the deflation valve on the inflator kit to adjust the pressure.
2. Once the desired pressure is reached, turn off the inflator.
3. The emergency puncture sealant will automatically seal any small holes or tears in the tire.

Step 5: Final Checks

1. After sealing, check the tire for any remaining signs of damage.
2. If there are no visible signs of damage, you can safely drive your vehicle to a repair shop for further inspection and permanent repair.

Frequently Asked Questions (FAQ)

Q: Can I use the tire inflator in the rain?

• A: No, it is not recommended to use the tire inflator in wet conditions or the rain.
• Keep the inflator dry and in a protected area.

Q: Can I use the tire inflator for other tasks?

• A: No, the tire inflator is specifically designed for inflating tires. Do not use it for any other purposes.

Q: What should I do if the tire damage is too big to fix?

• A: If the hole or tear in the tire is greater than 6mm, it is likely too big to be repaired with the puncture sealant.
• In such cases, it is recommended to seek professional assistance.

Q: Can I replace the 12-volt accessory plug with a different type?

• A: No, the 12-volt accessory plug should not be replaced with any other type of plug or electrical supply.
• Doing so may cause damage and invalidate the warranty.
• Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
• IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Stop somewhere safely away from other traffic. Try to avoid obstructing others.
• Make sure your handbrake is on and the car ignition is off.
• Turn on the vehicle’s hazard lights.
• Ensure you are visible to other road users whilst using the equipment.
• If available, wear a high-vis vest and set up a warning triangle.
• Keep the compressor clean and in good condition.
• Replace or repair damaged parts. Use recommended parts only. Unauthorized parts may be dangerous and will invalidate the warranty.
• Keep children and non-essential persons away from the work area.
• WARNING! This compressor is capable of producing a high pressure. DO NOT inflate any item beyond its maximum specified pressure.
• The 12-volt accessory plug must not be replaced with any other type of plug or electrical supply.
• DO NOT use near flammable solids, liquids, or gases.
• DO NOT direct the inflation hose connector head at yourself, others, or animals.
• DO NOT leave the compressor operating unattended. Always monitor it and the inflation pressure.
• DO NOT carry by the hose, or yank the hose from an inflation valve.
• DO NOT pull the plug from the accessory socket using the lead.
• DO NOT get the compressor wet or use it in the rain.
• DO NOT use the compressor for a task that it is not designed for.
• DO NOT operate the compressor when you are tired or under the influence of alcohol, drugs, or intoxicating medication.
• DO NOT operate the compressor if any parts are missing or the compressor is damaged, as this may cause failure and/or personal injury.
• DO NOT open the unit.

INTRODUCTION

• The emergency kit includes a 12V compressor, 450ml sealant bottle, accessories for inflatables, instructions, and a zipped storage bag fitted with hook and loop fastening for smart storage.

• Can seal a puncture up to Ø6mm at the roadside in under 10 minutes. Sealant
  is manufactured from natural rubber, meaning the tire can be washed out at the point of a professional repair.

• This very simple-to-use kit requires no tools, no need to remove the valve core and is TPMS safe. Plugs into a 12V vehicle accessory socket.

• Replacement sealant bottle available, Sealey Model No. MAC10SR. Suitable for cars, vans and 4x4s.

SPECIFICATION

• Model no.: ………………………………………………………MAC10S
• hose length (Compressor)………………………………….. 600 mm
• Hose length (Sealant bottle)……………………………….. 500 mm
• Operating voltage…………………………………………………….12V
• Maximum current……………………………………………………..10A
• Power cord length……………………………………………………..3m
• Maximum pressure…………………………………………….. 100 psi
• Typical inflation time…………………………………………..  195/55/R15 – 0-35psi in 270 seconds
• 450ml Replacement Tyre Sealant + Hose……………………. MAC10SR

CONTENTS

7

| Tyre valve Connector
4| Pressure gauge

Operation

GENERAL NOTES

• WARNING! Ensure you have read and understood the safety instructions.

Check the tire for physical signs of damage.

• NOTE: If the hole or tear is greater than 6mm it is probably too big to fix. Consider seeking assistance.
• DO NOT pull out any objects stuck in the tire, this might repair harder to achieve.
• NOTE: If possible, work on the tire with the hole/tear near the lowermost point of the tire. The sealant will work better that way.
• NOTE: When inflating/repairing a flat tire still fitted on a vehicle, there should not be any weight on it. The vehicle must, therefore, be jacked up to take the weight off the tire.
• Review jack safety instructions and vehicle manufacturer’s guidelines for jacking.
• Position the compressor on a firm, flat surface and located so that the air hose reaches the tire valve.
• IMPORTANT: Inflation will only be effective if the connectors are fully fitted.
• WARNING! The compressor must be switched off for twenty minutes after each twenty minutes of continuous operation to prevent excessive heat build-up.

PUNCTURE REPAIR

• NOTE: Review Section 5.1 before beginning this process.
• Unpack the unit and check that all items are present and in good working condition.
• Check that the compressor On/Off switch is in the OFF position and plug the 12V plug into the vehicle’s accessory socket.
• Gently shake the sealant bottle to mix it thoroughly.
• IMPORTANT: Repair will only be effective if the connectors are correctly fitted.
• Connect air hose (fig.1.6) to sealant air inlet connector (fig.1.1)
• Invert the sealant bottle and locate it into the face of the compressor (fig.1.2). Rotate clockwise to lock it in place.
• Connect sealant outlet (fig.1.7) to tire valve.
• Turn the compressor on to begin the process. Once the tire reaches the required pressure turn the compressor off.
• NOTE: If the tire has not inflated after approximately 10 minutes check all connections for leakage/blockage. If none is evident consider seeking assistance.
• NOTE: If the tire is accidentally over-inflated, use the relief valve on the air hose (fig.1.6) to allow air out of the tire.
• WARNING! After repairing the tire, the air hose and its connectors may be hot. Leave to cool for 2 to 3 minutes before removing.
• Remove all fittings and the power supply. Stow the items in a carry case and place the used sealant bottle in a leak-proof bag if available.
• Drive for about 2 miles (~3km) so that sealant can seal the damaged area. Stop and check tire pressure, and top up tire pressure if required.
• DO NOT drive faster than 50mph (80kph) on the repaired tire.
• DO NOT drive further than 125 miles (200km) on the repaired tire.
• DO NOT continue driving if any vibrations, unsteady steering, or noises occur. Consider seeking assistance.

TYRE / INFLATABLES INFLATION

• NOTE: Review Section 4.1 before beginning this process.
• Check that the compressor On/Off switch is in the OFF position and plug the 12V plug into the vehicle’s accessory socket.
• Remove the valve dust cap and screw the connector onto the valve stem.
• IMPORTANT: Inflation will only be effective if the connector is fully fitted onto the valve.
• Press the compressor On/Off switch to the ON position and the compressor will begin to operate.
• Inflate the tire to the desired pressure and turn off the compressor by pressing the switch to the OFF position.
• NOTE: The gauge may be subject to fluctuation whilst pumping.
• Remove the air hose from the tire valve by unscrewing the connector from the tire valve, taking care to minimize air loss in the process. Replace the dust cap.

Disconnect the 12V plug from the vehicle’s accessory socket

• NOTE: The pressure gauge is not a calibrated instrument. It is recommended to use a calibrated tire pressure gauge for an accurate final reading.
• NOTE: The compressor may also be used on items such as inflatable dinghies, sports balls, air beds, etc. using one of the two adaptors supplied.
• NOTE: If the tire/inflatable is accidentally over-inflated, use the relief valve on the air hose (fig.1.6) to allow air out.
• CAUTION: Some items may not indicate the pressure required or the safe maximum pressure. Be very careful not to over-inflate.

Maintenance

• Before each use check all hoses and fittings are sound and serviceable.
• Wipe down the unit with a damp cloth and dry thoroughly if soiled. DO NOT get the unit wet.
• Replace all hoses into relative compartments in the compressor body and place

Environment Protection

• Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment.
• When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

We Regulations

• Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE).
• When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and parts without prior notice.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.
• Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
• 01284 757500 01284 703534sales@sealey.co.uk www.sealey.co.uk
• © Jack Sealey Limited Original Language Version MAC10S Issue 1 31/10/19

Documents / Resources

| SEALEY MAC10S 12V Tyre Inflator Emergency Puncture Sealant Kit [pdf] Instructions
MAC10S 12V Tyre Inflator Emergency Puncture Sealant Kit, MAC10S, 12V Tyre Inflator Emergency Puncture Sealant Kit, Inflator Emergency Puncture Sealant Kit, Emergency Puncture Sealant Kit, Puncture Sealant, Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>