MERKURY MI-CW055-199W Smart Wi-Fi Outdoor Camera User Guide
- June 16, 2024
- Merkury
Table of Contents
MERKURY MI-CW055-199W Smart Wi-Fi Outdoor Camera
Specifications
- Product Name: Smart Wi-Fi Outdoor Camera
- Supported Platforms: iOS 13, Android 10
- Wi-Fi Network Compatibility: 2.4GHz (not compatible with 5GHz networks)
- Storage: Supports microSD card for recorded footage (not required)
Get Ready
Before setting up the camera, make sure you have the following:
- Smart Wi-Fi Outdoor Camera
- 3 x USB Cables
- Mounting Kit (Screws + Wall Anchors)
- Power Adapter
- User Manual
- Know your Wi-Fi network name and password
Product Usage Instructions
Download & Register
- Download the Merkury Smart App from the App Store or Google Play.
- Register an account on the app using your email address.
- Enter the verification code and create a password.
- Log in to the app using your account credentials.
Plugin
To reset the camera, press and hold the reset button for 10 seconds.
- If you’re using the included installation mount kit, screw the base of the camera to the desired location using the provided screws and anchors. Refer to the drawing for guidance.
- Unfold the included antenna and point it upwards for optimal signal reception.
- Mount the camera to the desired wall using the 3 screws and wall anchors.
- Adjust the camera to the desired angle and direction.
- Plug the camera into a power source using the included USB cable. The indicator will initially remain solid red during startup and will start blinking red when connected. If the indicator does not blink, please reset the camera using the reset button located on the USB cable.
Add Device (QR Code)
Make sure to reset the camera by pressing the reset button for 10 seconds before proceeding.
- In the Merkury Smart App, go to the Devices tab at the bottom and tap the “+” button in the top corner of the Devices screen.
INSTRUCTION
Thank you for purchasing your MERKURY smart home product.
Get started using your new devices by downloading the Merkury Smart App,
one convenient app that manages everything straight from your phone or tablet.
Easily connect to your home Wi-Fi, and control multiple devices from the touch
of your fingertips.
What’s in the Box
STEP 1
Download the Merkury Smart App from App Store or Google Play.
- Register an account on your App.
- Enter your email address.
- Enter the verification code and create a password.
- Log in to the App.
Resetting Device
Reset the Camera by pressing the reset button for 10 seconds.
STEP 1
Setup Camera
- If you would like to use the included installation mount kit, you can screw in the base of the camera using the included screws and anchors. Refer to the drawing.
NOTE : Before installing, be sure the desired location is accessible to a power source.
Plug-In
- Unfold the included antenna so that it is pointing upwards for an optimal signal.
- Use the included 3 screws and wall anchors to mount the camera to the desired wall.
- Adjust the camera to the desired angle and direction.
- Plug the camera into the power source using the included USB cable. The indicator will remain solid red when starting up but will begin to blink red when connected. If it does not blink, please reset the camera using the reset button located on the USB cable.
STEP 2
Add device:
-
Be sure to reset the camera by pressing the reset button for 10 seconds.
-
In the app, tap the “Devices” tab on the bottom and tap “+“ in the top corner of the Devices screen.
-
Choose “Wi-Fi Camera” and enter your Wi-Fi details.
-
Scan the QR code with the camera. When you hear the camera beep, select ‘I heard the sound’ and it will add your camera.
Connect Wi-Fi & QR scan -
The indicator light will turn solid blue when the device has connected successfully!
NOTE: This camera can’t connect to 5GHz networks.
Pairing Device
The app will attempt to connect. This may take a few moments.
STEP 3
Add tiles:
- Upon successful pairing, a tile for the camera will automatically be added to the dashboard. You can add tiles with the “+” on the Home page or resize, organize, and remove tiles by tapping “Edit”.
- Press the camera tile to view a live stream from the camera.
SETTINGS
Access Camera Settings
From your main device list, click the camera you want to edit, then click
Device Settings.
Device Name
Device Name to rename your camera to something like “Family room” or “Back
hallway”, then click Save.
Motion Zones
Click Motion Zones and then click on each square to deactivate or activate
that zone from detecting motion, then click Save.
Rotate image
If you mount your camera upside down, toggling this switch will rotate the
image so that it’s right side up.
Remove Device
Delete the camera from your account. Until it’s deleted, it will always be
linked to your account.
RULES
Create Motion & Sound Detection Rules
- Select the “Rules” tab on the bottom navigation bar and tap the “+” at the top corner of the screen.
- You can use a recommended rule, like “Record video and get notifications when motion is detected”, or create your own.
Frequently Asked Questions
-
How can I share videos with family and friends?
Select the “Activity” tab on the bottom navigation bar and view an activity to share with others. Use the “Share” button to choose how you want to share the activity event. -
How do I customize my dashboard?
Select the “Edit” option on the top of the “Home” page. Create additional pages on your dashboard by dragging tiles to the right and organizing devices to fit how you use them. -
How Many Devices Can I Control?
Merkury Smart app can control an unlimited amount of devices in an unlimited amount of locations. Your router may have a limit on how many devices can be connected to one router. -
How do I rename my device?
From your main device list, click on the device you want to rename, then click “Device Settings”, then click on “Device Name”. Rename your device to a more familiar name like “Bedroom” or “Living Room” and then click Save. -
The device appears offline or unreachable, what should I do?
Make sure your Wi-Fi router is online and in range. Make sure your device is plugged in and paired. You may also try restarting the device or if needed, re-pairing it. -
What’s the Wireless Range?
The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data. -
If my Wi-Fi/Internet goes down, will my devices still work?
Merkury products need to be connected to Wi-Fi to use them remotely.
Troubleshooting
Cannot connect to your Wi-Fi network.
Make sure you enter the correct Wi-Fi password during the Wi-Fi setup. Check
whether there are any Internet connection problems. If the Wi-Fi signal is too
weak, try moving the device closer to the router or reset your Wi-Fi router
and try again.
Reset the device
Reset the Camera by pressing & holding the reset button until the LED
blinks alternating slowly and quickly.
System Requirements
- Mobile device running iOS® 13 or higher or Android™ 10 or higher
- Existing Wi-Fi Network
Technical Specifications
- Camera: up to 1080p (1920 x 1080) at 15 frames/sec. H.264 encoding
- Field of View: 135° diagonal
- Audio: Internal Speaker and Microphone
- Storage: supports up to 128GB microSD card (not included) Wi-Fi not compatible with 5GHz Wi-Fi networks.
VOICE CONTROL GUIDE
Thank you for purchasing your Merkury Smart home product. Make sure your
devices are already set up using the app, then follow these steps.
Name and Control Each Device by Voice
To control your Merkury Smart home products, just say “OK Google,“ or “Hey Google,“ and ask. Make sure your devices are already set up using the app.
Things you can say Stream to
- Open the Google Home app and go to Home Control in the menu.
- Tap the “+“ button.
- Choose Merkury Smart from the list of Home Control partners
- Authorize your account with Google Assistant using the username and password from your app Now your Google Home app and Merkury devices are linked! You’re now able to say “Hey Google“ and control your Merkury devices.
- At any time, go into the “Home Control“ section of the Google Home app to set nicknames and rooms for your devices. You can rename your devices in the Merkury Smart app, and Google Assistant will refer to them by the same name.
So if you rename a camera to ‘Living Room Camera’ or ‘Baby’s Room,“ then Google Assistant will use that same name later on. You can always give it a nickname using the Google Home app as well.
To control your Merkury smart home products, just ask Alexa. Make sure your devices are already set up using the Merkury Smart app.
Things you can say Stream to:
Some commands require compatible devices.
- Open the Alexa app and go to Skills in the menu.
- Search for Merkury Smart Cam then tap Enable.
- Authorize your account with Smart Home Skills using the username and password from your Merkury Smart app.
- Choose “Discover Devices.“ After a few seconds, your Merkury devices will be displayed under Smart Home in the Alexa app.
- You can rename your devices in the app, and Alexa will refer to them by the same name. So if you rename a smart Cam to “Living Room“ or a nickname like a smart camera to “Living Room Camera” or “Baby’s Room,”
Alternatively, you can create an Alexa group, like “Bedroom“ or “Downstairs,“ and add the device to the group. Alexa will recognize the group name in the Alexa app, or the device name in the Merkury Smart app.
FAQ
Frequently Asked Questions (FAQ)
- Q: Can I use this camera with a 5GHz Wi-Fi network?
- A: No, this camera is only compatible with 2.4GHz Wi-Fi networks.
- Q: Do I need to use a microSD card for recording footage?
- A: No, a microSD card is not required for recording footage. However, it can be used if you want to save recorded videos.
- Q: How do I reset the camera?
- A: To reset the camera, press and hold the reset button located on the USB cable for 10 seconds.
- Q: Where can I find additional support?
- A: If you encounter any issues, please visit support.merkurysmart.com for assistance.
FCC
FCC Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, under part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
- The device has been evaluated to meet general RF exposure requirements.
- The device can be used in portable exposure conditions without restriction.
QR SCAN
Scan code for the latest manual online
Support
If you encounter any issues, please contact us at support.merkurysmart.com for help.
© 2023 Merkury Innovations 45 Broadway 3rd FL, New York NY 10006. The
illustrated product and specifications may differ slightly from those
supplied. iPhone, Apple, and the Apple logo are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is a service mark of
Apple Inc. Google, Google Play, and related marks and logos are trademarks of
Google LLC. iOS is a registered trademark of Cisco in the U.S. and other
countries and is used under license. Amazon, Alexa, and all related logos are
trademarks of Amazon.com, Inc. or its affiliates. All
other trademarks and trade names are those of their respective owners.
Made in Chin
Can’t connect? Need help?
DO NOT
RETURN THIS PRODUCT TO THE STORE
support.merkurysmart.com or tap ‘support‘
for help in the
Merkury Smart App.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>