STAIRVILLE BEL6 IP Bar HEX LED Bar User Manual

STAIRVILLE BEL6 IP Bar HEX LED Bar

Product Information

• Specifications
  • Product Name: BEL6 IP Bar HEX LED Bar
  • Date: 21.09.2023
  • ID: 471167 (V3)

Product Usage Instructions

• General Information
  • In this section, you will find an overview of the meaning of symbols and signal words that are used in this document.
• Symbols and Signal Words
  • This section provides the meaning of different symbols and signal words used in the user manual:

immediate dangerous situation that will result in death or serious
injury if it is not avoided.
WARNING!| This combination of symbol and signal word indicates a possible
dangerous situation that can result in death or serious injury if
it is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible
dangerous situation that can result in material and environmental
damage if it is not avoided.

Safety Instructions

• Intended Use
  • This device is intended for use as an electronic lighting effect using LED technology.
  • It is designed for professional use only and not suitable for households. Use the device strictly according to the instructions provided in this user manual.
  • Any other use or use under different operating conditions is considered improper and may result in personal injury or property damage.
  • The manufacturer does not assume liability for damages resulting from improper use.
  • This device should only be used by individuals with sufficient physical, sensory, and intellectual abilities, as well as corresponding knowledge and experience.
  • Other individuals may use this device only under supervision or instruction from a responsible person ensuring their safety.
  • To extend the operating life of the device, take regular breaks and avoid frequent switching on and off. The device is not suitable for continuous operation.
• Safety
  • DANGER! Risk of injury and choking hazard for children!
  • DANGER! Danger to life due to electric current! Inside the device, there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment, or optical components are missing or damaged.
  • DANGER! Danger to life due to electric current! A short circuit could lead to a fire hazard and risk of death. Always use a proper ready-made insulated triple-core mains cable with a safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect the power supply immediately and arrange for repair. If in doubt, seek advice from a qualified electrician.
• FAQ
  • Q: Can I use this device in my household?
  • A: No, this device is designed for professional use only and is not suitable for households.
  • Q: Can anyone use this device?
  • A: This device may only be used by individuals with sufficient physical, sensory, and intellectual abilities, as well as corresponding knowledge and experience. Other individuals may use this device only under supervision or instruction from a responsible person ensuring their safety.

General information

• This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future reference.
• Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this document.
• Our products and documentation are subject to a process of continuous development. They are therefore subject to change.
• Please refer to the latest version of the documentation, which is ready for download under www.thomann.de.

Symbols and signal words

• In this section you will find an overview of the meaning of symbols and signal words that are used in this document.

Safety instructions

Intended use

• This device is intended for use as an electronic lighting effect using LED technology.
• The device is designed for professional use only and is not suitable for use in households.
• Use the device only as described in this user manual.
• Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage.
• No liability will be assumed for damages resulting from improper use.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience.
• Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
• Extend the operating life of the device by regular breaks and by avoiding frequent switching on and off. The device is not suitable for continuous operation.

Safety

DANGER! Risk of injury and choking hazard for children!

• Children can suffocate on packaging material and small parts.
• Children can injure themselves when handling the device.
• Never allow children to play with the packaging material and the device.
• Always store packaging material out of the reach of babies and small children.
• Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervision.
• Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with.

DANGER!

• Danger to life due to electric current! Within the device, there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged.

DANGER!

• Danger to life due to electric current! A short circuit could lead to a fire hazard and risk of death. Always use proper ready-made insulated triple-core mains cable with a safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect immediately the power supply and arrange a repair. If in doubt, seek advice from a qualified electrician.

WARNING!

• Risk of eye damage caused by high light intensity! The device generates highly intense light radiation. Looking directly into the light source can damage the eyes. Never look directly into the light source.

WARNING!

• Risk of epileptic fit due to flashing lights! The device emits flashing lights (strobe effects). Flashing lights can trigger epileptic fits in specific people. If you are at risk of epilepsy, avoid spending longer periods subjected to flashing lights and looking into strobing lights.

WARNING!

• Incorrect handling of lithium batteries can result in injury! In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries. Handle lithium batteries correctly and professionally. Store lithium batteries in a cool and dry place in their original packaging. Keep lithium batteries away from sources of heat. Never open lithium batteries. Only charge rechargeable lithium batteries with a suitable charger. Remove the lithium batteries before disposing of the device. Cover the poles of used lithium batteries with adhesive tape to prevent short circuits. Electrolytes can escape from damaged lithium batteries. Put the damaged lithium battery in air-tight packaging. Collect the electrolyte with absorbent paper. Wear rubber gloves while doing so.

NOTICE!

• Risk of fire due to covered vents and neighbouring heat sources! If the vents of the device are covered or the device is operated near other heat sources, the device can overheat and burst into flames. Never cover the device or the vents. Do not install the device near other heat sources. Never operate the device near naked flames.

NOTICE!

• Damage to the device if operated in unsuitable ambient conditions! The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the ambient conditions specified in the “Technical specifications” chapter of this user manual. Avoid operating it in environments with direct sunlight, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature fluctuations. If temperature fluctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in operation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by qualified specialists at regular intervals to prevent damage due to overheating and other malfunctions.

NOTICE!

• Damage to the device due to high voltages! The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess voltages can also cause a risk of injury and fires. Make sure that the voltage specification on the device matches the local power grid before plugging in the device. Only operate the device from professionally installed main sockets that are protected by a residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or the device will not be used for a longer period.

NOTICE!

• Risk of fire by exceeding the maximum current The device can supply power to other devices of identical design and connected in series. If too many devices are connected, the power consumption can exceed the maximum permitted power consumption, which can cause the device to overheat and burst into flames. Only connect devices of identical design to the device. When deciding how many devices you can connect in series, make sure that the maximum permitted power consumption as stated on the device is not exceeded. Also, refer to the specifications in the technical specifications for the device. Only use power cords with a cable cross-section designed for the required current intensity when connecting the devices in series.

NOTICE!

• Risk of fire due to incorrect polarity! Incorrectly inserted batteries may cause fires and destroy the device and the batteries. Observe the markings on the batteries and the device. Ensure that proper polarity is observed when inserting batteries.

NOTICE!

• Possible damage due to leaking batteries! Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period.

NOTICE!

• Possible staining due to plasticiser in rubber feet! The plasticiser contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor.

NOTICE!

• Possible damage to lithium-ion batteries through incorrect storage! Deep discharge can permanently damage lithium-ion batteries or cause them to lose some of their capacity. Charge the lithium-ion batteries before longer breaks in use and before storage. Ensure that the device is switched off for storage. Store the device at room temperature or cooler in an environment as dry as possible. Recharge the lithium-ion batteries about every three months if they are stored for a longer period to avoid permanent damage due to too deep self-discharge. Fully charge the lithium-ion batteries only shortly before use at room temperature.

NOTICE!

• Possible damage due to moisture penetrating open connectors! Moisture entering open connectors (plugs and couplings) of DMX and power supply cables can cause short circuits and damage to connected fixtures. Always seal unused connectors with end caps intended for this purpose (www.thomann.de).

Features

Special features of the device:

• Six six-colour LEDs (RGBAWUV, each 15 W)
• Battery-operated LED bar for outdoor use
• Integrated W-DMX-G5 receiver
• Operable in stand-alone or DMX mode
• Control via DMX, via W-DMX, with the supplied infrared remote control and via the HD colour display with touch-sensitive buttons on the device
• 36 selectable mixed colours and effects programmes
• Sound control via built-in microphone
• Various mounting options
• Built-in receiver module for wireless control, compatible with Wireless Solution 5G
• W-DMX transmitter optionally available (item number 573998)

For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperatures. You can extend the service life of the illuminates by providing adequate ventilation and operating the LEDs with the lowest possible brightness.

Installation

• Unpack and check carefully there is no transportation damage before using the unit.
• Keep the equipment packaging.
• To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your packaging material suitable for transport or storage, respectively.

Information about protection class IP65

• Equipment with protection class IP65 is dust-tight and completely protected against contact (first code number).
• They are also protected against splash water from any angle (second code digit).
• That is why this equipment can also be used outdoors. Event technology equipment is generally only designed for temporary use, however (event lighting) and not for permanent use outdoors.
• The specified protection class does not make a statement about the weather resistance of the equipment (resistance to changing ambient conditions as well as against the effects of sunlight and UV rays).
• The seals and screw connections of the equipment must be checked regularly to ensure a fault-free operation. In cases of doubt, consult a specialist workshop in due time.

WARNING!

• Risk of injury from falling devices that were inadequately secured!
  • If devices are not properly secured during assembly, they can cause severe injury and considerable damage by falling.
  • When installing and operating, make sure to follow the standards and regulations that apply in your country.
  • Always secure the device with a secondary safety attachment, such as a safety cable or a safety chain.

NOTICE!

• Risk of overheating due to bad ventilation!
  • If the device is badly ventilated, the device can overheat.
  • Do not operate the unit at ambient temperatures outside the specified temperature range (see chapter “Technical data” of the user manual).
  • Always ensure sufficient ventilation at the operating location.

NOTICE!

• Potential property damage due to unsuitable stands!
  • If the device is mounted on an unsuitable stand, there is a risk that the stand will fall over and cause damage.
  • Only use stands whose maximum bearing capacity is at least as high as the weight of the device. Always ensure that the stand is stable.

NOTICE!

• Data transfer errors due to improper wiring!
  • If the DMX connections are wired incorrectly, this can cause errors during the data transfer.
  • Do not connect the DMX input and output to audio devices, e.g. mixers or amplifiers.
  • Use special DMX cables for the wiring instead of normal microphone cables.

Notes on radio transmission

• This equipment uses a frequency range that is free of charge and registration within the European Union.
• For more information, please visit http://www.thomann.de.
• Make sure that no metal objects are located between the transmitter and receiver.
• Avoid interference by other radio and in-ear systems.

Mounting options

• You can install the device in a hanging or standing fashion or on a stand.
• When in use, the device must always be attached to a solid surface or an approved mount.
• Use the threads provided for mounting.
• Always work from a stable platform whenever installing, moving or servicing the device.
• While you do this, the area underneath the device must be cordoned off.
• The safety cable must be threaded through the safety eyelet.
• Please note that this device must not be connected to a dimmer.

Infrared sensor for the remote control

• The infrared sensor for the remote control signals is located between the LEDs on the front panel of the device. Make sure it is not obstructed.

Inserting the battery into the remote control

• Push the lock of the battery holder towards the centre of the housing and pull out the battery holder like a drawer.
• Insert the batteries.
• The battery is correct if the positive pole points to the housing base of the remote control.
• Slide the battery holder back into the remote until it clicks into place.
• When shipping, the battery is already installed in the remote and protected against discharge by a transparent plastic film.
• Remove the plastic film before initial use.

NOTICE!

• Risk of fire due to incorrect polarity!
  • Incorrectly inserted batteries may cause fires and destroy the device and the batteries.
  • Observe the markings on the batteries and the device.
  • Ensure that proper polarity is observed when inserting batteries.

NOTICE!

• Possible damage due to leaking batteries!
  • Batteries can leak and cause permanent damage to the device.
  • Take the batteries out of the device if it is not going to be used for an extended time.

Starting up

• Create all connections while the device is off.
• Use the shortest possible high-quality cables for all connections.
• Take care when running the cables to prevent tripping hazards.

Connections in DMX mode

• Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device.
• Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain.
• Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 Ω, ¼ W).

Connections and controls

power supply.
---|---
6| [PRESSURE VALVE] | Pressure compensation valve (prevents condensation inside the device)
7| Safety eyelet for attaching the safety cable
8| [ON / OFF] | Main switch. Turns the device on and off
9| [POWER OUT] | Lockable output socket (Seetronic Power Twist TR1) for powering a further device.
10| [DMX OUT] | DMX output
11| HD colour display
12| Touch-sensitive buttons
| Activates the main menu and toggles between menu items. Closes an opened submenu
/   | Toggle between the menu items of a menu level, increase or decrease the displayed value by one
 | Selects an option of the respective operating mode, confirms the set value
13| [DMX IN] | DMX input

Remote control

14| [BLACK OUT] | Enables or disables blackout.
---|---
15| [AUTO] | Starts or stops the “automatic” mode.
16| [SOUND] | Starts the sound-controlled automatic show.
17| [STROBE] | Starts or stops the strobe effect with the last selected colour.
---|---
18| [SPEED] | Allows you to set the speed of the automatic programs with the [+] and [–] buttons.
19| [SENSITIVITY] | Allows you to set the sensitivity of sound control with the [+] and [–] buttons.
20| [%] | Resets the displayed value to zero during the setting of values (speed of the automatic programs, sensitivity of sound control).
21| [MANUAL] | Activates the display of a constant colour, which you can either mix individually from primary colours using [R] , [G] and [B] , or select directly with one of the coloured buttons.
22| [FADE] | Allows you to choose between the two automatic options by pressing repeatedly.
23| [R] , [G] , [B] | Sets the intensity of the three primary colours red, green and blue when a constant colour is displayed.
24| [A] , [UV] , [W] | Sets the intensity of the colours amber, white and UV when a constant colour is displayed.
25| [+] , [–] | Increases or decreases the set value.
26| Buttons for directly selecting a mixed colour.

Operating

Starting the device

• Connect the device to the power supply to start operation.
• After a few seconds, the display indicates that a reset is in progress.
• The device is then ready for use.
• The display shows the operating mode that was selected when the unit was last powered off.

Main menu

Press to activate the main menu. Use or to select a submenu. When the display shows the desired submenu press to open it up. To close the main menu, press . The stored values are displayed in white in the display. Changed values are displayed in red until they are confirmed with .  All previously made settings are retained even when you disconnect the device from the power grid. To restart with default values, use the function ‘Factory Reset’ (see Ä Chapter 7.3 ‘Reset to factory default setting’ on page 34). The following table shows the setting options.

Meaning
‘DMX Address’| 001…512| Setting the DMX address
‘Mode’| ‘DMX’| Selecting a DMX mode| Highest possible DMX address
‘ 6Ch’| 6-channel DMX mode| 507
‘10Ch’| 10-channel DMX mode| 503
‘Auto’| Auto run with fade effect
‘Fade’| ‘Sp00’ … ‘Sp99’| Speed of the fade effect
Main menu| Menu level 2| Menu level 3| Menu level 4
---|---|---|---
Meaning
| ‘Sound’| Sound-controlled autorun
‘Step’| ‘Se00’ … ‘Se99’| Sensitivity of the built-in microphone
‘Static’| ‘Dimmer’| 0…255| Setting the overall brightness
‘Strobe’| 0…255| Stroboscope effect with adjustable speed
‘C-Macro’| 1…36| Selection of a mixed colour (see ‘¼ ‘Selectable mixed colours’

on page 32)

‘Red’| 0…255| Intensity red (0 % to 100 %)
‘Green’| 0…255| Intensity green (0 % to 100 %)
‘Blue’| 0…255| Intensity blue (0 % to 100 %)
‘White’| 0…255| Intensity white (0 % to 100 %)
Main menu| Menu level 2| Menu level 3| Menu level 4
---|---|---|---
Meaning
| | ‘Amber’| 0…255| Intensity amber (0 % to 100 %)
‘UV’| 0…255| Intensity UV (0 % to 100 %)
‘Slave’| ‘Slave’| Operating mode ‘Slave’
‘Settings’| ‘W-Dmx’| Wireless DMX control
‘On’| Disabled
‘ Off ’| Enabled
‘Display’| Automatic display shutdown when not in use
‘On’| Enabled
‘ Off ’| Disabled
‘Display Rev’| Display inversion
‘On’| On, the display is rotated by 180°
‘ Off ’| Off, normal display
‘Limiter’| Lowering the maximum brightness to extend battery life
Main menu| Menu level 2| Menu level 3| Menu level 4
---|---|---|---
Meaning
| | ‘On’| Enabled
‘ Off ’| Disabled
‘DMX Fail’| Device behaviour on DMX signal failure
‘Blackout’| Blackout
‘Sound’| Sound-controlled autorun
‘Auto’| Auto run with fade effect
‘Hold’| Retaining last settings
‘Dimmer Curve’| Dimmer curve selection
‘Linear’| Linear
‘Exp’| Exponential
‘Log’| Logarithmic
‘S Curve’| S-shaped
‘System Info’| ‘Firmware’| Show the firmware version of the device
‘Time info’| Operating hours display
‘Temperature’| Show device temperature

Selectable mixed colours

Reset to factory default setting

• Press and hold and simultaneously until the display shows ‘Reset’. Confirm with to reset the device to factory defaults.
• Press to cancel the procedure.

Menu overview

Functions in 6-channel DMX mode

Functions in 10-channel DMX mode

Technical specifications

Light source

Optical properties

| 6 × RGBAWUV LED, each 15 W
---|---
Beam angle| 25°
Control| DMX
W-DMX
Infrared remote control
Number of DMX channels Input connections| 6, 10
Power supply| Lockable input socket (Seetronic Power Twist TR1)
DMX control| IP65 Seetronic XLR chassis socket, 3-pin
Output connections| Power supply

DMX control

| Lockable output socket (Seetronic Power Twist TR1)
IP65 Seetronic XLR chassis socket, 3-pin
Power consumption| 70 W
W-DMX| Frequency range| 2403 MHz…2479 MHz
Light source

Optical properties

| 6 × RGBAWUV LED, each 15 W
---|---
Beam angle| 25°
Control| DMX
W-DMX
Infrared remote control
Number of DMX channels Input connections| 6, 10
Power supply| Lockable input socket (Seetronic Power Twist TR1)
DMX control| IP65 Seetronic XLR chassis socket, 3-pin
Output connections| Power supply

DMX control

| Lockable output socket (Seetronic Power Twist TR1)
IP65 Seetronic XLR chassis socket, 3-pin
Power consumption| 70 W
W-DMX| Frequency range| 2403 MHz…2479 MHz
Ambient conditions| Temperature range| 0 °C…40 °C
---|---|---
Relative humidity| 20%…80% (non-condensing)

Plug and connection assignments

• Introduction
  • This chapter will help you select the right cables and plugs to connect your valuable equipment so that a perfect light experience is guaranteed.
  • Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or ‘just’ a not working light show!
• DMX connections
  • The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input.
  • Please refer to the drawing and table below for the pin assignment of a suitable XLR plug.

Troubleshooting

NOTICE!

• Data transfer errors due to improper wiring!
• If the DMX connections are wired incorrectly, this can cause errors during the data transfer.
• Do not connect the DMX input and output to audio devices, e.g. mixers or amplifiers.
• Use special DMX cables for the wiring instead of normal microphone cables.
• In the following, we list a few common problems that may occur during operation.

We give you some suggestions for easy troubleshooting:

proper connection.
2. Check the address settings and the DMX polarity.
3. Try using another DMX controller.
4. Check whether the DMX cables run near or parallel to high-voltage cables that may cause damage or interference to a DMX interface circuit.
The built-in battery can no longer be charged| Do not attempt to replace the built-in battery yourself. Please contact our service centre.

If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de.

Cleaning

Optical lenses

Clean the optical lenses, that are accessible from the outside, regularly to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device.

• Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).
• Always dry the parts carefully.

Fan grids

• The fan grids of the device must be cleaned of any contamination, such as dust, etc. regularly.
• Before cleaning, switch off the device and disconnect mains-operated devices from the mains.
• Only use pH-neutral, solvent-free and non-abrasive cleaning agents.
• Clean the unit with a slightly damp lint-free cloth.

Protecting the environment

Disposal of the packaging material

• For the packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
• Ensure that plastic bags, packaging, etc. are properly disposed of.
• Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling.
• Please follow the notes and markings on the packaging.

Disposal of batteries

• Batteries must not be thrown away or incinerated; they must be disposed of by local regulations for the disposal of hazardous waste.
• Use the existing collection points for this.
• Only dispose of lithium batteries when they are discharged.
• Remove replaceable lithium batteries from the device before disposal.
• Protect used lithium batteries against short circuits, for example by covering the poles with adhesive tape.
• Permanently built-in lithium batteries must be disposed of together with the device.
• Please inquire about an appropriate collection point.

Disposal of your old device

• This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.
• Do not dispose of your normal household waste.
• Dispose of this device through an approved waste disposal firm or your local waste facility.
• When discarding the device, comply with the rules and regulations that apply in your country.
• If in doubt, consult your local waste disposal facility.

CONTACT

• Thomann GmbH
• Hans-Thomann-Straße 1
• 96138 Burgebrach
• Germany
• Telephone: +49 (0) 9546 9223-0
• Internet: www.thomann.de.
• 21.09.2023, ID: 471167 (V3).

References

• Buy musical instruments online from the market leader – Thomann United States

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>