KORGOL 59 x 24 In Electric Single Motor Standing Desk Instruction Manual

June 16, 2024
KORGOL

Instruction Manual Electric Single Motor Standing Desk

MADE IN CHINA
Important-Please read these instructions before assembly.
If you encounter any problems during installation, please feel free to contact us!
IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.

GENERAL GUIDELINES

  • Please read the following instruction carefully and use the product accordingly.
  • Please keep this manual and hand it over when you transfer the product.
  • This summary may not include every detail of all variations and considered steps.
    Please contact us when further information and help are needed.

NOTES

  • Please follow the assembly instructions precisely and only use the product as intended.
  • If an odor is present when first opening the package. please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
  • Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use product as damage or injury may occur;
  • Please contact us for assistance and replacement.
  • During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
  • It is suggested you regularly check the products bolts and connections to ensure safe use.
  • Assemble the item on a soft flat and clean surface to avoid scratches and damage.

WARNING

  • During assembly, keep parts and packaging materials away from children and pets as there could cause injury and are a potential choking hazard.
  • Avoid sharp objects or corrosive chemicals to prevent damage to the product.
  • Please open the item slowly and cautiously to avoid pinching your hands by metal joints. especially children.

Components

Please check you have all the pieces listed below

Part List

Reference| Description| Part| Quantity| Material
1| Desktop-a| | 1| MDF
2| Desktop-b| | 1| MDF
3| Desktop-c| | 2| MDF
4| Left Leg| | 1| Steel
5| Right Leg| | 1| Steel
6| Support Beam| | 2| Steel
7| Side Bracket| | 2| Steel
8| Base| | 2| Steel
9| Sync Rod| | 1| Aluminium

KORGOL 59 x 24 In Electric Single Motor Standing Desk -
FigKORGOL 59 x 24 In Electric
Single Motor Standing Desk - Component Notice!
When the screw is tightened, do not continue to tighten it forcefully, otherwise the screw may be damaged.

KORGOL 59 x 24 In Electric Single Motor Standing Desk - Component
1| KORGOL 59 x 24 In Electric
Single Motor Standing Desk - Component 2
---|---
KORGOL 59 x 24 In Electric Single Motor Standing Desk - Component
3| KORGOL 59 x 24 In Electric
Single Motor Standing Desk - Component 4
KORGOL 59 x 24 In Electric Single Motor Standing Desk - Component
5| KORGOL 59 x 24 In Electric
Single Motor Standing Desk - Component 6

CONTROLLER INSTRUCTION

IMPORTANT You must RESET the desk prior to use.
RESET Setting Method 1: Press and hold “/V and “V” buttons on the handset at

the same time for seconds until you hear the beep. Release the buttons. The desk will goes automatically until It shows 69, and the reset Is successful.
Height Adjustment| Up: Press Up”‘∧” Down: Press Down “V”
Switch Display| Press 2 tlmes”V”when the desk at the lowest position to switch cm to Inch
Memory Height| Press and hold any of memory buttons (1,2,3 or 4) until you hear a beep.Release the button, and this position height will be stored In memory.
When the worl<ing height of memory needs to be used, press the memory position button and the desk will automatically adjust to the memory height.
Note:This standing desk has 4 different height memories. The memory positions stored are still valid after power off. You can use the up and down buttons to adjust the standing desk to the height you need to work.

Troubleshooting Gulde:

If your standing desk does not worl< property, you may need to reset It. If any error codes appears, you need to reset It.

Maintenance and Consideration:

  1. During dally maintenance, use a clean soft cloth to remove surface dust. Do not use a wet cloth or hard material to wipe the surface of the table.
    Avoid contacting the surface with acid-based chemicals.

  2. For slight scratches, gently wipe with a soft cloth, you can smooth out scratches.
    Avoid attaching tape directly to the outer surface of the metalfeet to prevent paint from peeling

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals