ANALOG DEVICES UG-2054 Wireless Development Boards User Guide
- June 16, 2024
- Analog Devices
Table of Contents
User Guide
EVAL-ADPA7009-2
UG-2054
Evaluating the ADPA7009-2 20 GHz to 54 GHz, GaAs, pHEMT, MMIC, 29 dBm (0.5 W)
Power Amplifier
ADPA7009-2-EVALZ EVALUATION BOARD PHOTOGRAPHS
FEATURES
- 2-layer Rogers 4350B evaluation board with heat spreader
- End launch 1.85 mm RF connectors
- Through calibration path
EVALUATION KIT CONTENTS
- 2-layer Rogers 4350B evaluation board with heat spreader
EQUIPMENT NEEDED
- RF signal generator
- RF spectrum analyzer
- RF network analyzer
- 5 V, 1.5 A power supply
- −1.5 V, 10 mA power supply
GENERAL DESCRIPTION
The ADPA7009-2-EVALZ consists of a 2-layer printed circuit board (PCB)
fabricated from 10 mil thick Rogers 4350B copper clad mounted to an aluminum
heat spreader. The heat spreader assists in providing thermal relief to the
ADPA7009-2 as well as mechanical support to the PCB. Mounting holes on the
heat spreader allow it to be attached to larger heat sinks for improved
thermal management. The RFIN and RFOUT ports are populated by 1.85 mm female
coaxial connectors, and their respective RF traces are of 50 Ω characteristic
impedance. The ADPA7009-2-EVALZ is populated with components suitable for use
over the entire operating temperature range of the ADPA7009.
RF traces are 50 Ω grounded coplanar waveguide. Package ground leads and the
exposed pad connect directly to the ground plane. Multiple vias are used to
connect the top and bottom ground planes, with particular focus on the area
directly beneath the ground paddle to provide adequate electrical conduction
and thermal conduction to the heat spreader.
The power supply decoupling capacitors shown in Figure 4 represent the
configuration that was used to characterize and qualify the device.
It is possible to reduce the number of capacitors; however, this reduction
varies by system. It is instead recommended to first remove
or combine the largest capacitors that are farthest from the device.
Consult the ADPA7009 data sheet in conjunction with this user guide when
working with the ADPA7009-2-EVALZ board.
OPERATING THE ADPA7009-2-EVALZ
The ADPA7009-2 operates by externally biasing the gate voltage.
Adjust VGG1 within the −1.5 V to 0 V range through J5 or VGG2 within the −1.5
V to 0 V range through the J6 header to set the target drain current.
See the ADPA7009-2 data sheet for the bias sequencing information.
Ground and gate control voltages are accessed through two 8‑pin headers (see
Table 1 for the header pinout).
Table 1. J5 and J6 Header Connections to the ADPA7009-2
| Header Pin No. | ADPA7009-2 Pin |
|---|
J5
8
4
2 3, 5, 6, and 7¹| VGG1
VDD1
VREF
GND¹
J6
7
3
1 4, 5, 6, and 8¹| VGG2
VDD2
VDET
GND¹
1 These header pins are connected to all GND pins, and the exposed pad of the ADPA7009-2 on the evaluation board.
THROUGH CALIBRATION PATH
To calibrate out board trace losses, a through (thru) calibration path is
provided between J3 and J4. J3 and J4 must be populated with RF connectors to
use the through calibration path.
Figure 3 shows the plot of the data in Table 2 of the through calibration path
(J3 to J4). See Figure 4 for the evaluation board
schematic.
Table 2. Insertion Loss and
Return Loss of Through Calibration Path
| Frequency (GHz) | Insertion Loss (dB) |
|---|
0.1
1
5
10
15
20
25
30
35
40
45
50
55| –0.03
–0.18
–0.49
–0.83
–1.08
–1.30
–1.53
–1.73
–1.92
–2.16
–2.40
–2.63
–3.01
EVALUATION BOARD SCHEMATIC AND ARTWORK
ORDERING INFORMATION
BILL OF MATERIALS
Table 3.
| Reference Designator | Description | Manufacturer | Part Number |
|---|
C1, C2, C7, C8, C13, C14 (do not install, DNI) C3, C4, C9, C10 (DNI) C5, C6,
C11, C12 J3, J4 (Not Installed) RFIN, RFOUT J5, J6
R1, R2 U1
Not applicable| 100 pF ceramic capacitors, 0402 0.01 μF ceramic capacitors,
0603 Tantalum capacitors, 4.7 µF, 20 V, 10%, 3216-18 CONN-PCB, 1.85 mm, coax,
50 Ω, 67 GHz CONN-PCB, 1.85 m coax, 50 Ω, 67 GHz Connectors, PCB header,
vertical, dual row, 8‑position,
2 mm pitch
100 kΩ resistors, SMD, 5%, 1/10 W, 0402 20 GHz to 54 GHz, gallium arsenide
(GaAs),
pseudomorphic high electron mobility transfer
(pHEMT), monolithic microwave integrated circuit
(MMIC), 29 dBm (0.5 W) power amplifier
Aluminum heat spreader, 02.51 in. × 1.9 in.| Not applicable Not applicable AVX
HIROSE ELECTRIC CO. HIROSE ELECTRIC CO.
Molex
Panasonic
Analog Devices, Inc.
Not applicable| Not applicable
Not applicable
TAJA475K020RNJ
HV-LR-SR2(12)
HV-LR-SR2(12)
87759-0814
ERJ-2GEJ104X
ADPA7009-2ACEZ
Not applicable
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit
boards can discharge without detection. Although this product features
patented or proprietary protection circuitry, damage may occur on devices
subjected to high energy ESD. Therefore, proper ESD precautions should be
taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools,
components documentation or support materials, the “Evaluation Board”), you
are agreeing to be bound by the terms and conditions set forth below
(“Agreement”) unless you have purchased the Evaluation Board, in which case
the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not
use the Evaluation Board until you have read and agreed to the Agreement. Your
use of the Evaluation Board shall signify your acceptance of the Agreement.
This Agreement is made by and between you (“Customer”) and Analog Devices,
Inc. (“ADI”), with its principal place of business at Subject to the terms and
conditions of the Agreement, ADI hereby grants to Customer a free, limited,
personal, temporary, non-exclusive, non-sublicensable, non-transferable
license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer
understands and agrees that the Evaluation Board is provided for the sole and
exclusive purpose referenced above, and agrees not to use the Evaluation Board
for any other purpose. Furthermore, the license granted is expressly made
subject to the following additional limitations: Customer shall not (i) rent,
lease, display, sell, transfer, assign, sublicense, or distribute the
Evaluation Board; and (ii) permit any Third Party to access the Evaluation
Board. As used herein, the term “Third Party” includes any entity other than
ADI, Customer, their employees, affiliates and in-house consultants. The
Evaluation Board is NOT sold to Customer; all rights not expressly granted
herein, including ownership of the Evaluation Board, are reserved by ADI.
CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be
considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other
party for any reason. Upon discontinuation of use of the Evaluation Board or
termination of this Agreement, Customer agrees to promptly return the
Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not
disassemble, decompile or reverse engineer chips on the Evaluation Board.
Customer shall inform ADI of any occurred damages or any modifications or
alterations it makes to the Evaluation Board, including but not limited to
soldering or any other activity that affects the material content of the
Evaluation Board. Modifications to the Evaluation Board must comply with
applicable law, including but not limited to the RoHS Directive. TERMINATION.
ADI may terminate this Agreement at any time upon giving written notice to
Customer. Customer agrees to return to ADI the Evaluation Board at that time.
LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED
“AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH
RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS,
GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE,
FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY
RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S
POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST
PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY
FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US
DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or
indirectly export the Evaluation Board to another country, and that it will
comply with all applicable United States federal laws and regulations relating
to exports. GOVERNING LAW. This Agreement shall be governed by and construed
in accordance with the substantive laws of the Commonwealth of Massachusetts
(excluding conflict of law rules). Any legal action regarding this Agreement
will be heard in the state or federal courts having jurisdiction in Suffolk
County, Massachusetts, and Customer hereby submits to the personal
jurisdiction and venue of such courts. The United Nations Convention on
Contracts for the International Sale of Goods shall not apply to this
Agreement and is expressly disclaimed.
Downloaded from Arrow.com.
analog.com
©2022 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
One Analog Way, Wilmington, MA 01887-2356, U.S.A.
Rev. 0 | 4 of 5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>