ADuM1252S Evaluation Kit Evaluates: ADuM1252, ADuM1253,
ADuM1254, ADuM1255

General Description

The ADuM1252S evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the features of the ADuM1252, a 2-channel bidirectional reinforced digital isolator with ultra-low standby current in an 8-pin narrow SOIC surface-mount package. The ADuM1252S EV kit can be used to evaluate the functionality and electrical performance of the ADuM1252. The EV kit is powered by two independent power supplies.
The ADuM1252S EV kit can also be used to evaluate the ADuM1253, ADuM1254, or ADuM1255

Features and Benefits

• Data Transfer Rates from DC to 2MHz
• Wide Voltage Supply Range from 1.71V to 5.5V
• Convenient Four-Point I2 C Bus Connection
• Guaranteed up to 3.0kV RMS Isolation for 60s
• Support Onboard Supply-Current Measurement
• -40°C to +125°C Temperature Range
• Proven PCB Layout
• Fully Assembled and Tested

Ordering Information appears at end of data sheet.

ADuM1252S EV Kit Photo

Quick Start
Required Equipment

• ADuM1252S EV kit
• Two DC power supplies with an output range of 1.71V to 5.5V
• Signal/function generator (or I 2 C compatible signals,SDA and SCL)
• Oscilloscope

Procedure
The ADuM1252S EV kit is fully assembled and ready for evaluation. Use the following steps to verify board operation.

1. Verify jumper settings. See Table 1.
2. Connect one DC power supply between the EV kit’s VDD1 and AGND1 test points; connect the other DC power supply between VDD2 and AGND2 test points.
3. Set both DC power supply outputs at 3.3V, and then enable the power supply outputs.
4. Connect a signal/function generator (or I 2 C compatible signals, SDA and SCL) to SDA1 or SCL1 test points and observe the isolated signal on side 2 using an oscilloscope.

Table 1. Jumper Connection Guide

*Default options

Considerations for evaluating the ADuM1253, ADuM1254 or ADuM1255
The ADuM1253 and ADuM1255 have a unidirectional clock channel, which only allows a signal flow from SCL1 to SCL2.
Therefore, they do not support clock stretching and require that the I 2 C controller be located on the side 1 bus. For the ADuM1253, all other features and parameters are similar to the ADuM1252.
The ADuM1254’s features and parameters are similar to the ADuM1252, with the primary difference that the ADuM1254 offers a lower level of guaranteed performance. The ADuM1255 is the unidirectional clock variant of the ADuM1254.
Hence, it comes with a similarly lower guaranteed performance comparted to the ADuM1252 (or ADuM1253).
The ADuM1253 or ADuM1255 may be substituted for the installed ADuM1252 when the unidirectional clock is to be evaluated.

Detailed Description of Hardware

The ADuM1252S EV kit evaluates the features of the ADuM1252, 2-channel bidirectional galvanic digital isolators in an 8-pin narrow SOIC package for I2C applications. The EV kit is powered by two individual power supplies from 1.7V to 5.5V.
Jumper Connection
Jumpers J1 and J2 are provided for easy current meter connections. To measure the supply current from either side 1 or side 2, remove the shunt on the jumper and connect a current meter to the respective jumper directly.
Jumpers J3 and J4 give users options for current measurement or disconnecting SDA2 and SCL2 pins from on-board pull-up resistors R3 and R4. To verify the Hot Swap precharged voltage on pins SDA2 and SCL2, be sure no shunt on J3 and J4.
The ADuM1252S EV kit allows multi access for signal connections, see Table 2. Jumper J9 provides a convenient location for a four-point I 2C bus connection allowing the EV kit to communicate with an I 2 C bus with either twisted wire or a 4-pin header.
Decoupling Capacitor
Each power supply is decoupled with 0.1µF and 1000pF ceramic capacitors, which are placed close to V DD1 and V DD2 pins.
Pullups
SDA and SCL are connected to its corresponding VDD with a 1kΩ pull-up resistor. The EV kit is optimal at 3.3V operation. The user can change the pull-up resistors for different supply voltages.
Output Load
Each SDA and SCL_ signal trace is provided with unpopulated 0805 case surface mount footprints (C7 to C10) to allow different loads on customer requirements.
Table 2. Signal Connections

J7 pins 2 and 3
J5 pins 2 and 3
J9 pin 2
SCL1| test point SCL1| SCL2| test point SCL2
J8 pins 2 and 3
J6 pins 2 and 3
J9 pin 2

Ordering Information

Denotes RoHS compliance.

ADuM1252S EV Kit Bill of Materials

REFERENCE
DESIGNATOR| QTY| DESCRIPTION| MANUFACTURER| PART NUMBER
---|---|---|---|---
AGND1(3x), AGND2(2x), SCL1, SCL2, SDA1, SDA2, VDD1, VDD2| 11| SMT test point| Keystone| 5017
C1, C2| 2| 10pFt 10%, 16V X7R ceramic capacitor (0805)| Samsung
Murata
CAL-CHIP| CL21B106KOONNN
GRM21BZ71C106KE15
GMC21X7R106K16NT
C3, C4| 2| 0.l pF ±10%, 25V X7R ceramic capacitor (0603)| TDK
KEMET
AVX| C1608X7R1E104K080AA,
C0603C104K3RAC
06033C104KAT2A
C5, C6| 2| 1000pF ±5%, 50V COG ceramic capacitor (0402)| Murata
TDK| GRM1555C1H102JA01
C1005COG1H102J050
C7, C8| DNI| 20 pF ±5%, 100V COG ceramic capacitor (0805)| N/A| NIA
C9, C10| DNI| 390 pF ±5%, 100V COG ceramic capacitor (0805)| N/A| NIA
J1 J4| 4| 2-pin header, straight through hole male connector| Sullins| PCCO2SAAN
J5-J8| 4| 3-pin header, straight through hole male connector| Sullins| PCCO3SAAN
J9| DNI| 4-pin header, straight through hole male connector| N/A| NIA
R1 R4| 4| 1k0 ±1%, % W thick film chip resistor (0805)| Vishay Dale
Panasonic| CRCW08051 KOOFK
ERJ-6ENF1001
U1| 1| ADuM1252 (8-pin Narrow SOIC)| Analog Device Inc.| ADuM1252ASA+
None| 1| ADuM1252S EV kit Rev A board| N/A| NIA
None| 4| Round through hole spacer| Keystone| 9032
None| 4| Shunt| Samtec Inc.| SNT-100-BK-G

ADuM1252S EV Kit Schematic Diagram

ADuM1252S EV Kit PCB Layout

Revision History

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

www.analog.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>